Kayfun LITE - Part 2

[MattB101]

Completely off topic but I just finishing cleaning the clone V4 and am getting ready to wick it up. Wish me luck.


Sent with no malice and not a whole lot of forethought from my new Galaxy Tab 4. Thanks Santa!

 

[MattB101]

Darn things got some parts doesn't it?

Sent with no malice and not a whole lot of forethought from my new Galaxy Tab 4. Thanks Santa!

 

[MattB101]

Here's my KFL+ v2 with a Plasma tank from Trippy Tips. Love this glass tank.

I like it, gotta unique look to it. Might have to get me one. Is it just the bell and drip tip or the whole rig?

Sent with no malice and not a whole lot of forethought from my new Galaxy Tab 4. Thanks Santa!

 

[Grrrr]

It's a single piece of glass fused to the threaded metal part of a kayfun.

 

[qorax]

Vaping Postcard Time

Not a KFL, but a Kayfun nonetheless

 

[MKID]

If I am driving from low to high altitudes should I flip/turn over my kayfun so it does not leak even if I vape through the change of altitude? If so, should I have a cup or some container ready in case it leaks?

 

[Dusty_D]

If I am driving from low to high altitudes should I flip/turn over my kayfun so it does not leak even if I vape through the change of altitude? If so, should I have a cup or some container ready in case it leaks?

Traveling with my KFL's I usually take them off whatever device I have it from, wrap it in a tissue, and keep it upside down in a pocket of my backpack.

 

[MKID]

Traveling with my KFL's I usually take them off whatever device I have it from, wrap it in a tissue, and keep it upside down in a pocket of my backpack.

If I am driving through the change of altitude and want to vape as I drive, do I still need to keep it upside down?

 

[Dusty_D]

If I am driving through the change of altitude and want to vape as I drive, do I still need to keep it upside down?

No, you shouldn't have to, as long as you're vaping on it. It's when it's resting that it gets affected from my experience.

 

[MKID]

No, you shouldn't have to, as long as you're vaping on it. It's when it's resting that it gets affected from my experience.

I got to learn two things at once, Thanks

 

[LittleBird]

Good morning, all! I have an uneducated, noobie question. Please forgive if already asked and answered; I'm running low on energy, this morning

I can't unscrew the stainless middle section so that I can replace it with the clear plastic section. Brand new KFL+ 2nd batch, just assembled (used all stainless sections) yesterday. It's my very first one, so I might be missing something. But it's stuck! Is there a trick to this? Thanks!

 

[MKID]

Good morning, all! I have an uneducated, noobie question. Please forgive if already asked and answered; I'm running low on energy, this morning

I can't unscrew the stainless middle section so that I can replace it with the clear plastic section. Brand new KFL+ 2nd batch, just assembled (used all stainless sections) yesterday. It's my very first one, so I might be missing something. But it's stuck! Is there a trick to this? Thanks!

There is a hot cold method mentioned somewhere in this thread, I am pretty sure someone will help you!

 

[Bronze]

If I am driving through the change of altitude and want to vape as I drive, do I still need to keep it upside down?

I learned to vape standing on my head.

 

[Bronze]

Good morning, all! I have an uneducated, noobie question. Please forgive if already asked and answered; I'm running low on energy, this morning

I can't unscrew the stainless middle section so that I can replace it with the clear plastic section. Brand new KFL+ 2nd batch, just assembled (used all stainless sections) yesterday. It's my very first one, so I might be missing something. But it's stuck! Is there a trick to this? Thanks!

LB, some people throw it in the freezer for awhile and have had luck with that. Also, get yourself a pair of rubber gloves (or those rubbery jar grip thingies) to get a better grip. Going forward, get yourself some mineral oil and swab a thin film on the thread/o-rings with a q-tip. Just a thin film is all that is needed. It makes it much easier to unscrew. Just do the large exterior threads and rings (base, tank segments, top cap). Don't want to do the interior threads/rings on the chimney or inside top cap.

 

[LittleBird]

LB, some people throw it in the freezer for awhile and have had luck with that. Also, get yourself a pair of rubber gloves (or those rubbery jar grip thingies) to get a better grip. Going forward, get yourself some mineral oil and swab a thin film on the thread/o-rings with a q-tip. Just a thin film is all that is needed. It makes it much easier to unscrew. Just do the large exterior threads and rings (base, tank segments, top cap). Don't want to do the interior threads/rings on the chimney or inside top cap.

Thanks, Bronze. I just put it in the freezer. Can I use No-Ox?

 

[HDMontana]

I cut a wide rubber band in a few pieces. Wrap one of the pieces around each part of the tank that you are trying to seperate. It gives you a good gripping surface. Might help you.

HD

 

[ricks]

Good morning, all! I have an uneducated, noobie question. Please forgive if already asked and answered; I'm running low on energy, this morning

I can't unscrew the stainless middle section so that I can replace it with the clear plastic section. Brand new KFL+ 2nd batch, just assembled (used all stainless sections) yesterday. It's my very first one, so I might be missing something. But it's stuck! Is there a trick to this? Thanks!

This is hard to describe but I find that sometimes while trying to take these apart you have to try unscrewing it with a gentle grip. Meaning you can't squeeze it too tight. Just try to hold it in different positions and different grips while trying to take it apart. Does anyone know what I'm talking about??? It's kind of strange but it works for me.

 

[Bronze]

Thanks, Bronze. I just put it in the freezer. Can I use No-Ox?

No Ox is a forbidden topic on this thread!!!

 

[Bronze]

This is hard to describe but I find that sometimes while trying to take these apart you have to try unscrewing it with a gentle grip. Meaning you can't squeeze it too tight. Just try to hold it in different positions and different grips while trying to take it apart. Does anyone know what I'm talking about??? It's kind of strange but it works for me.

Yes, that will work for me at times too. I don't have much trouble with the parts where I use the mineral oil, but the chimney I don't use mineral oil (for obvious reasons). Sometimes that hat wont come off. I'll go from manhandling it to finessing it and the finesse will work. There is a sweet spot to find where it will unscrew easily.

 

[ricks]

Yes, that will work for me at times too. I don't have much trouble with the parts where I use the mineral oil, but the chimney I don't use mineral oil (for obvious reasons). Sometimes that hat wont come off. I'll go from manhandling it to finessing it and the finesse will work. There is a sweet spot to find where it will unscrew easily.

Happens with my cocktail shaker all the time.