Killer 705 atty

[MikeA5]

When adjusting the killer juice control with the AGR I take the AGR base off adjust the juice control then put the AGR base back on and away I go.
Here's the link for Todd's killer in the AGR: http://www.youtube.com/watch?v=InzA4G6xT9Y

 

[tmcase]

When adjusting the killer juice control with the AGR I take the AGR base off adjust the juice control then put the AGR base back on and away I go.
Here's the link for Todd's killer in the AGR: AGR2 SS Carto Tank (Killer tested) - YouTube

Thanks for the link. I know see why it wouldn't work on my vmax.

 

[beebopnjazz]

My floating post comes out...easily Have to be careful not to lose it......didn't have that issue until I had that horrible time with the ceramic.......is there a way to seat it better so that it floats but not down to the floor?

And I tried to use the AGR without the adapter from the killer - have no idea how you did it - the stem wasn't long enough to make the connection....

 

[SheerLuckHolmes]

I'm using the AGR on a Vamo. No issues. The air flow adjustment has to be done with your fingers on the threads of the Killer bottom section since the tanks bottom cap screws into place and stays there. So each time you need to refill the tank you have to take it off of your device close the juice control with your fingers. Fill the tank. Reopen the juice control with your fingers then put it back onto the device. But other than that it works really well.

 

[tmcase]

My floating post comes out...easily Have to be careful not to lose it......didn't have that issue until I had that horrible time with the ceramic.......is there a way to seat it better so that it floats but not down to the floor?

And I tried to use the AGR without the adapter from the killer - have no idea how you did it - the stem wasn't long enough to make the connection....

I don't know if this will help what you are talking about but before I seat the ceramic cup I screw the killer onto an ego battery so that floating pin won't come out. It seems to be working fine for me this way.

I don't have any mods with those airholes on the top cap so I have to use the bottom locking adapter.

 

[beebopnjazz]

Yours comes out easily too then?

I don't know if this will help what you are talking about but before I seat the ceramic cup I screw the killer onto an ego battery so that floating pin won't come out. It seems to be working fine for me this way.

I don't have any mods with those airholes on the top cap so I have to use the bottom locking adapter.

 

[tmcase]

Yours comes out easily too then?

Yes, everytime.

 

[FogHawg]

Aah, so there is a pin that comes loose when the ceramic pc is taken out. Good to know cause I bet that little rascal would be hard to replace if it were lost.

 

[tmcase]

Aah, so there is a pin that comes loose when the ceramic pc is taken out. Good to know cause I bet that little rascal would be hard to replace if it were lost.

Actually the pin comes out when you push the ceramic cup on.

 

[FogHawg]

Actually the pin comes out when you push the ceramic cup on.

Hmmm, that sounds sorta counter-intuitive to me, what holds the pin in place once everything is assembled? I guess I'll figure it out once I tear into it. I'll def be keeping an eye on that pin now tho. Thanks again!

 

[Koman]

When adjusting the killer juice control with the AGR I take the AGR base off adjust the juice control then put the AGR base back on and away I go.
Here's the link for Todd's killer in the AGR: AGR2 SS Carto Tank (Killer tested) - YouTube

Good video, thanks man!

 

[Absintheur]

I have rewicked mine several times...never noticed the pin moving...

 

[MikeA5]

So far I've been lucky when installing the ceramic cup the center pin has not come out on me, but if it did no problem just push it back in.
Here's a video of Bishop Heals building a dual coil on the Killer where the center pin comes out on him. He puts the 510 adaptor on (the juice control one) which holds the 510 pin in place while inserting the ceramic cup.
Leo's Killer with UFS .6 Ohms Dual Highlander Style 4.2 volts - YouTube

Edit: it's about 19min into the video

 

[JJOOHHNN]

Dang this is a long thread. It seems like people are liking these.

 

[JJOOHHNN]

I read enough to convince me that I needed this. I now see they are out of stock.

 

[benosa562]

I read enough to convince me that I needed this. I now see they are out of stock.

Theres a couple in the classifieds

 

[Natural]

Is there any posts or lists that show which tanks people have used the killer on and any special considerations when using those specific tanks?

I am hoping my killers, when i get them, will work on my prives, traps, and phiniac tanks without any issues.

 

[grindle]

Is there any posts or lists that show which tanks people have used the killer on and any special considerations when using those specific tanks?

I am hoping my killers, when i get them, will work on my prives, traps, and phiniac tanks without any issues.

From a thread on UKVapers

YES List

Wee Boaby( needs different rings)
Siam tank
Kazulinho mods
Phiniac ( using ss end caps)
Kir Fanis, Prive/Trap/Angel/tripolitis
AGR version 2? (The one with 2 bottom pieces)
DCT Olympian
Phiniac

 

[IraSurefire]

Does anyone know if the killer works on the big daddy or Lil mama tanks? I suspect that it does...

Sent from my SCH-I535 using Tapatalk 2

 

[tmcase]

From a thread on UKVapers

From the list above it says (Phiniac...using ss end caps). The killer works in Phiniac tanks with the Derlin (sp) top caps also.