That bullet cut drip tip is really good lookin'! About to pull the trigger on a 3rd!
- Status
That bullet cut drip tip is really good lookin'! About to pull the trigger on a 3rd!
Thanks. It normally lives on my eBaron Dripper Pro but when I'm dripping with the Killer it's a perfect match.
I personally put a new one in every 3-4 days or when I change the juice, whichever comes first. Sometimes I only have a coil and wick in there for half a day before it gets replaced. They take me about 6-7 min to rebuild and I make sure that usually have at least 5 on the ready. Same thing with my eBaron so they share a supply of about 18 cups. It usually means that once every two weeks I sit down for an hour or so and build a bunch of them.
Just like any other RBA. If it loses flavor or vapor then it's time to replace. You are probably use a juice that is easy on coils.
mucho gracias gentlmen. One final q - has anyone tried rebuilding without the non resistance wire and what are your results?
Sent from my Galaxy Nexus using Tapatalk 4 Beta
Sent from my Galaxy Nexus using Tapatalk 4 Beta
Mine came pre built with no no-resistance wire, it worked just fine for 3 weeks, no problems at all. Yesterday I built it with no-resistance wire because I think it may save battery
The non resistant wire may have been there but the soldier connection is so tiny that you may have missed it.
i ran mine for about 2.5 weeks before it gunked up so bad that i couldn't clean any of it off. i used a dark sweet juice that i'm sure was the reason why it stuck so badly. i did wash it out twice with hot water without recoiling it. Now i'm waiting for materials to rebuild. I think i'll need more ceramic cups...
I just got the Vaperfexion Killer Cartomator VX tank. I have had loads of trouble getting a Killer 705 to be an enjoyable experience for me. The only thing that has worked for me is a GG UFS. So I was skeptical while setting up the VX. Holy smokes, the end caps where in there tight. Really tight. But once I had carefully removed them and used some e-juice around the glass it was no longer a big deal. I installed the Killer used it all last night and this morning. The Killer and the VX were made for each other... Well at least the VX is made specifically for the Killer and works flawlessly. Not one problem. Just a good vape each and ever toot!
I am a happy camper..... finally
I am a happy camper..... finally
Hah, yup you and me both. It left LA on the 24th. If you count only week days it's been 9 days in transit. LA is not that far from Vancouver BC which is pretty close to me.
Last edited:
So the last two days of vape mail have been fantastic. My Lexi and my ibtanked showed up.
First off, I love the look of this tank. The stock I rings are almost the perfect tightness and I can get the bottom cap off super easy to fill it. It doesn't hurt that it's paper thin and amazing. There were some other o rings included of different size that I might play with. Maybe really tight on the top cap and lose on the bottom one. As of now I like them just how they are. I had the tube custom cut and its pretty much exactly the right size , super happy with that. The only down side is that because the caps are so thin it raises the juice flow hole pretty far above the bottom. Oh well a tiny bit of wasted juice is worth it.
First off, I love the look of this tank. The stock I rings are almost the perfect tightness and I can get the bottom cap off super easy to fill it. It doesn't hurt that it's paper thin and amazing. There were some other o rings included of different size that I might play with. Maybe really tight on the top cap and lose on the bottom one. As of now I like them just how they are. I had the tube custom cut and its pretty much exactly the right size , super happy with that. The only down side is that because the caps are so thin it raises the juice flow hole pretty far above the bottom. Oh well a tiny bit of wasted juice is worth it.
The Killer very rarely fails to impress me. Though yesterday I had wicking issues for the first time and it was annoying. But blocking the air flow and giving a long pull to suck some juice in helped.
Killer tank from Vaperfexion has arrived....
Is the full port on the top cap one of the options to choose from, I only see the one with a fill port in the tube. Thanks.
Guys did anybody try to fit the Killa into the X8 tank?
$7.47 Authentic X8 2.5ml Electronic Cigarette Atomizer at FastTech - Worldwide Free Shipping
Thanks a lot in advance.
$7.47 Authentic X8 2.5ml Electronic Cigarette Atomizer at FastTech - Worldwide Free Shipping
Thanks a lot in advance.
- Status
Similar threads
