Probably Tobeco. They're the most prominent Veritas cloner, by far! And as we have learned, they don't have a stellar reputation.
Let's Talk Hardware
- Thread starter Pappy
- Start date
- th_trl_thread_readers 0
- Status
Probably Tobeco. They're the most prominent Veritas cloner, by far! And as we have learned, they don't have a stellar reputation.
I checked , one guy said he contacted Eccigity about it and they're carrying both versions , the timeline doesn't allow for it to be the Ehpro version .Probably Tobeco. They're the most prominent Veritas cloner, by far! And as we have learned, they don't have a stellar reputation.
I'm guessing I don't have much to worry about. I don't pour 50 watts into my Veritas and chain vape them like those boys do. LOL!
vape mail today! Unfortunately, the Ehpro Veritas has to go back. The one I got has the top cap utterly fused to the deck base. It is impossible to spin (as you would to adjust airflow) or to lift it off. I put it on my MVP (used for builds and coil burns) to hold the deck, and pulled on the top - nothing! Not budging.
Is there some trick I am missing?
I even soaked it in hot soapy water thinking there might be some machine grease in there. Didn't help.
I've emailed Vivid Smoke to see about getting a replacement.
Is there some trick I am missing?
I even soaked it in hot soapy water thinking there might be some machine grease in there. Didn't help.
I've emailed Vivid Smoke to see about getting a replacement.
Try putting it in the freezer for awhile after you get some water in it , it might force things apart when you take it out , it's probably stuck on an o-ring
probably the new oring is stuck due to sticktion I would do a hot water dip/boil to make the oring soft and pliable to remove the top.... freezing just might make the oring too hard to flex...
The freezer did not help. I'm heading out now. I think this RDA is defective. Later!
They were cheap...so far no issues but I only put it on last night...I will let you know after a week if I have any issues...I like being able to use a couple of my favorite drip tips that just look goofy with the original top.
they even have ones that can be filled from the top..
BK invented a new word (again)!
Love the top IG. I have those coming too. Where's the drip tip from? looks red, very nice.
LA vs. the Veritas - Round 2
Returned with food and beer consumed and a new mind to conquer. Used a small screwdriver wedged between the deck and the cap to leverage it up all around. Victory is mine! The cap is off.
BK had it nearly right (though I didn't see his post until after I fixed it). Half of the top o-ring had been pushed down. It was resting over the bottom o-ring making a double layered seal on one side. Made for a tight seal of top cap to bottom deck.
It's apart and soaking for a good cleaning before I try my first build. Gonna go for a 28ga horizontal micro coil aiming for around 1 ohm.
Can't send it back now thanks to twice slipping with the screwdriver for a couple of shallow scratches on the outside of the top cap. Meh. For $25 and something to play with, I can live with it.
Thanks again, gents!
Returned with food and beer consumed and a new mind to conquer. Used a small screwdriver wedged between the deck and the cap to leverage it up all around. Victory is mine! The cap is off.
BK had it nearly right (though I didn't see his post until after I fixed it). Half of the top o-ring had been pushed down. It was resting over the bottom o-ring making a double layered seal on one side. Made for a tight seal of top cap to bottom deck.
It's apart and soaking for a good cleaning before I try my first build. Gonna go for a 28ga horizontal micro coil aiming for around 1 ohm.
Can't send it back now thanks to twice slipping with the screwdriver for a couple of shallow scratches on the outside of the top cap. Meh. For $25 and something to play with, I can live with it.
Thanks again, gents!
Bull box mods....used it on my Zens...it's always been one of my favorites
- Status
Similar threads
- Locked
- Locked
