Got a little bit done today probably still won't have anytime to get the fun stuff in till next weekend.
Cavity routed and holes drilled
Cavity routed and holes drilled
Mike n Tibs DNA Mods!
- Thread starter Proetus
- Start date
- th_trl_thread_readers 0
- Status
Yeah he did a good job on all of the blocks I got, I'll make sure to take pics with a good camera once it's finished since my phone apparently only takes pics in shades of blue 
I stumbled onto this thread and couldn't help myself to order a box. Here is what I got so far..
1x Dome Button Set in Stainless Steel
1x Tibs mod - Dual 18650 - Battery Tray in White Strong & Flexible
1x Tibs Mod - Dual 18650 - Back in Black Strong & Flexible
1x Obround - Tibs Mod - Dual 18650 - FD510 - Case in Black Strong & Flexible
Atmistique has DNA30D boards in stock so I grabbed one (along with an EVIVA) and a charging board from Evolv.
Big question is what 510 should I use? I have some Chi clones that am thinking might be able to be modded to fit or should I wait for the one talked about in the Co-Op?
Am I missing anything and how long does it take to get the parts from Shapeway?
Can't wait to get everything and begin the building!
1x Dome Button Set in Stainless Steel
1x Tibs mod - Dual 18650 - Battery Tray in White Strong & Flexible
1x Tibs Mod - Dual 18650 - Back in Black Strong & Flexible
1x Obround - Tibs Mod - Dual 18650 - FD510 - Case in Black Strong & Flexible
Atmistique has DNA30D boards in stock so I grabbed one (along with an EVIVA) and a charging board from Evolv.
Big question is what 510 should I use? I have some Chi clones that am thinking might be able to be modded to fit or should I wait for the one talked about in the Co-Op?
Am I missing anything and how long does it take to get the parts from Shapeway?
Can't wait to get everything and begin the building!
Shapeways generally takes 2-4 weeks.
If you bought the Tibs Mod then it was made to use a Fat Daddy 510 talked about in the thread.
Do check out the Tibs Mod co-op interest thread.
You will need the special battery contacts for the battery holder.
Speaking of which, did you order the battery holder? I think it may be a separate part.
You will also want fuses.
Do check out these 2 threads, all the info you need can be found in them.
http://www.e-cigarette-forum.com/forum/coop-planning-discussion/541992-tibs2-bap.html
http://www.e-cigarette-forum.com/fo...ussion/549096-odds-ends-round-2-tibs-mod.html
Finished up Big Blu's smaller brother....
Fat Daddy 510 modified with spring loaded center pin!
Hammered Copper Paint
Blue faceplate
Red Faceplate
Together!
Fat Daddy 510 modified with spring loaded center pin!
Hammered Copper Paint
Blue faceplate
Red Faceplate
Together!
No doubt there will be, but are the dimensions the same as the original that the design is built around! I know the coop version will work Bap will make it
I think they will work with the existing Mod on Shapeways. Even better in fact, as the new FD510s wont need to be modified like the first ones were designed to be.No doubt there will be, but are the dimensions the same as the original that the design is built around! I know the coop version will work Bap will make it
The new FD510 will actually have a bigger diameter head, so it won't be a drop in replacement. I thought Dennis said he would be getting in some more of the original connectors, I will have to check with him on that.
But remember the original FD510 does need to be modified to fit in the Tibs mod.
Finished up Big Blu's smaller brother....
Blue faceplate
What battery are you using in this? Can I assume LiPo of some sort?
Yes small 1200mah 25c lipos. I was gonna use two and actually wired it up that way initially, but it was extremely tight fit and I didn't like the pressure being put on the screen/board when putting the faceplate on.
Last edited:
Finished up Big Blu's smaller brother....
Blue faceplate
For some reason,
"I Am NOMAD"
popped into my brain. But does look like a mighty small handful. lol. Maxed out would probably only gotten half the way to Alpha Centaury, and kirk never would of had to save earth.
Finally got this project together. I gave a sneak peak earlier, but here is the completed mod. DNA 30 from the first co-op and the body is Shapeways printed. I airbrushed with jet black acrylic and finished it with polyurethane. I used an unmodified Fatdaddy 510 and whole mess of cool parts to make the connections for the removable top. Its only a first prototype, but I'll post up details if anybody is interested.
I gave a sneak peak earlier, but here is the completed mod. DNA 30 from the first co-op and the body is Shapeways printed. I airbrushed with jet black acrylic and finished it with polyurethane. I used an unmodified Fatdaddy 510 and whole mess of cool parts to make the connections for the removable top. Its only a first prototype, but I'll post up details if anybody is interested.
Ok...had some time this morning to write-it up... http://www.e-cigarette-forum.com/fo...printed-dna30-bottom-feeder.html#post13055948
FYI the original Fat Daddy 510 will be available again, there is plenty of demand for it. In addition, I was told there would be two new versions up in the next 1-2 weeks, one of which should be the spring-loaded. Not clear what the other new one is.
- Status
Similar threads
