Teemu (maker of the Boxer) was working on a single cell SX box similar to the Boxer.Tired of the black burnt Wick? I'm keeping my SX350j. I would really like a single 18650 3D printed enclosure for it. No luck finding a nice one Yet
I'm going to remove it from taking to work detail and bring my BRD 1300 to work instead
Mike n Tibs DNA Mods!
- Thread starter Proetus
- Start date
- th_trl_thread_readers 0
- Status
Has to be 2mm based on the volume. Only way to get a cheaper print. I do think that 2mm should be fine with gusseting.
Found It S-26J Battery Holder (RTGF54Q8U) by teemu_kangas
It's over 100 bucks for all 3 pieces needed
What's He thinking? I could sell my SX mod and put in the 100 plus dollars and get a mini for that much. I need some thing good for half that price.
I have 2 Zephyrus's. There nice tanks. Definitely lung hitters, the RBA deck is a little small to work on. The top fill works nicely, I still never tried the pre built coils for it.
I think it's a nice option, If your out and about for long periods of time you can bring a spare pre built coil just in case
The tank capacity is a little small, it goes through juice like crazy.
Over all it's a pretty good tank
Well I've been using the Zephyrus for a couple days, really LOVE the flavor! But.... the leaking from the prebuilt heads is disappointing, I tried both the kanthal and the nickle, I vape 80 VG- 20 PG. The air flow is massive, if you put a hose one the air intake you could subba dive and easily breath through this thing! But the flavor really kicks in at the half way mark for the juice, coil ad wattage I'm using. I haven't tried building the RBA deck yet and most likely won't until I need to replace the head, the prebuilt nickle head is very impressive! Although I hate the thought of dishing out $4-5 for a head, if it last long enough I just might consider it. I don't plan on making this my all day vaping atty so we'll see, I'm not a fan of building coils and wicking anymore then I have too.
It amazes me where vaping has taken me and I still find it hard to believe I'm using a DAN200 with a sub-ohm tank with nickle coils, never ever dreamed that would happen. Yesterday I stopped by the local shop I been frequenting the last few years, there is one young guy there I kind of got to be friendly with and asked him if he had seen the 200 yet. Well he flipped out over it, he went and brought the owner out to check it out, he went nuts over it, before I knew it everyone was standing around checking it out. They wanted to see the inside, they brought me a screw driver and I let them check it out, the owner asked me if I would build some for them to sell, the whole response by everyone really took me by surprise but I think they were all surprised to see me, this old guy, walk in with something like that after being a pro tank and isitck customer.
It's about $80 for the 3 parts for that mod but I was talking about this one (not available anywhere):
Ouch, $80... But it is a very nice looking setup!
$80 bucks for this:Ouch, $80... But it is a very nice looking setup!
The green one is the mod I was originally talking about, not the S26-J (in the video above).
It's about $80 for the 3 parts for that mod but I was talking about this one (not available anywhere):
Well thats a freaking nice mod! not available any were? Man that sucks
Can I email the guy? you think it would help?
I want one of those
Sent him an email on SW finger crossed he replies and I can get one.
Last edited:
Leaking from the pre built heads? disappointing
I have never tried the ones I got with mine. I do how ever like the RBA section and no leaking from that
Glad to hear you like the Zephyrus
Enjoy your celebrity status at the B&M
Gusseting would help with strength and stability, but not external fire/puncture protection. Fine Polyamide PA 2200 (Shapeway's Strong and Flexible nylon plastic) has a melt temperature of 80°C and a flash point of 350°C. Ideally, walls should be thick enough to prevent external fire threats or punctures from quickly encroaching upon the battery compartment. Realistically I'm less concerned with the external fire issue, but a too thin wall is more of a concern for a battery puncture during a drop event. Most of my designs are using primarily 4mm walls (with some 3mm spots for fitment purposes) and I definitely notice the increased cost. For my own use, I won't go with anything less than 3mm...unfortunately the cost is dramatically increased as you've pointed out. However, the reduction in cost isn't worth it to me to go with 2mm walls since I am certain that I'll drop a mod at some point.
Last edited:
OK So I have been a bit slow on making mods but here you go.
From one (or more) of Mike's co-ops
DNA40 Big Screen Squonker and DNA200 with 3s 1300mah lipo using the on chip buttons
From one (or more) of Mike's co-ops
DNA40 Big Screen Squonker and DNA200 with 3s 1300mah lipo using the on chip buttons
OK So I have been a bit slow on making mods but here you go.
From one (or more) of Mike's co-ops
DNA40 Big Screen Squonker and DNA200 with 3s 1300mah lipo using the on chip buttons
Nice job! Love the two tone wood, the black face lends well and the brass buttons just finish it off nicely.
Nice job! Love the two tone wood, the black face lends well and the brass buttons just finish it off nicely.
Those are from Floris Delfino in Italy. The squonker has a veneer applied to the faceplate he provides. The DNA200 is one of the two faceplates he provided with it. Those both just have a few coats of Danish Oil on them. I have several more that I am doing with alcohol based stains then danish oil and wax. Good price for the enclosures. in the 20 to 30$ range on them.
I talked to him thru email a couple weeks ago, he said he was working on dna200 boxes.... I didnt know he actually had them yet.. what did you use for buttons?
He did a run of 5 wanting feedback. Wire routing was an issue on these I drilled some not so pretty holes in it to show him where to holes need to go. New run coming soon. If you facebook look at his product page he announces info there. They are designed to use vamo button actuators. You can get them from UK mod supply houses. Or you can do like I did and give the picture from stealth vape with the dimensions to a machinist and ask nicely for buttons
Poasted with my DNA30 Toaster using Sorcery
Pics of the inside where I drilled ugly holes in his otherwise fantastic design.
Poasted with my DNA30 Toaster using Sorcery
Poasted with my DNA30 Toaster using Sorcery
Pics of the inside where I drilled ugly holes in his otherwise fantastic design.
Poasted with my DNA30 Toaster using Sorcery
Were the holes too small or were they non-existent?
The little round holes were his. I think for some reason he assumed the mounting holes on the board were for power in and out. The holes for the landing pads for power were non-existent. All in all it was no biggie. I had the drill press set up for something else at work or I would have done a neater job. I have a cross slide for the drill press. One hour for lunch does not give me a lot of time for retooling, plus it was friday, the danish oil was dry and I wanted to vape it this weekend
- Status
Similar threads
