Mike n Tibs DNA Mods!
- Thread starter Proetus
- Start date
- th_trl_thread_readers 0
- Status
I considered that as well, but assume the software would detect the chip in play...we shall see.
So maybe a new chip in the near future? An addition to the Escribe Family
Another Co-Op? A single or Dual 18650 60 to 75/100 watt TC chip would be nice
Or maybe both a single 18650 60 watt and a dual 18650 100 watt TC Chip?
IMO they should utilize the 18650's everybody has them and the chargers
Would round out the Evolv family nicely
Anyone looking for a Good Deal!
I paid way too much for a black one like this. I put a DNA40 in it and it's been a great little mod.
So for this price I will have a silver one to. I just happen to have one small screen DNA40 left over from the Co-Op before the 200's
$32.26 Infinite ZERO Modz Styled VW Variable Wattage APV Box Mod - 7-40W / 1*18650 / stainless steel / grey at FastTech - Worldwide Free Shipping
I paid way too much for a black one like this. I put a DNA40 in it and it's been a great little mod.
So for this price I will have a silver one to. I just happen to have one small screen DNA40 left over from the Co-Op before the 200's
$32.26 Infinite ZERO Modz Styled VW Variable Wattage APV Box Mod - 7-40W / 1*18650 / stainless steel / grey at FastTech - Worldwide Free Shipping
Morning Tibsnobody liked the grey? all other combos are twice as much
morning, steamer!
The fit and Finnish of the one I have is really good. It's real small to. The chip was a little inaccurate But I'm going to mod it any way
There is a small board that holds the fire and up down buttons with a common ground it all has to be re wired. I don't think it would be a big deal for any one hanging around in this thread
whats up guys n gals =)
I love this rta but got tired of using latex gloves when undoing the parts.
It needs some texture around top &bottom imo.
A little off topic But just had to show all of you this! I need one!
The tank section looks like plastic in the photo but it will be glass in the production modle
available end of August?
Did I mention I need 1 or 2 of these?
Cuthulu RTA V2
Features:
1. Cuthulu RTA Ⅱ Cuthulu RTA comes with two desks(single coil and dual coil);
2. Bigger airflow and bigger desk.
3. 2 posts and 4 holes design for dual coil desk;(super easy for coil building)
4. Access to the build deck without draining the tank
5. Juice flow control
6. Easier top fill system.
7. Lip around the oval air hole to prevent leaking
8. Bigger juice channels than V1
9. Easy to remove top fill cap.
10. Adjustable 510 pin
I love this rta but got tired of using latex gloves when undoing the parts.
It needs some texture around top &bottom imo.
OK, I know..... 
But they offer some neat stuff I thought some of you might like Unique Gifts & Innovative Products by Makers | The Grommet
ETA: Like this Liquid Bonder Kit by Bondic
But they offer some neat stuff I thought some of you might like Unique Gifts & Innovative Products by Makers | The Grommet
ETA: Like this Liquid Bonder Kit by Bondic
Not sure why you'd say "off topic" with that, Willy. That has lots of applications in a mod. Nice find!
I didn't see the plastic welder until after I posted. They have some really strange things too, who the hell would use one of these?
Power Nap Pillow - Ostrich Pillow
OK, I know.....
But they offer some neat stuff I thought some of you might like Unique Gifts & Innovative Products by Makers | The Grommet
ETA: Like this Liquid Bonder Kit by Bondic
I bought some off eBay not too long ago. Used it a few times for holding parts together until epoxy cures. Works well for that but it can be a bit fickle to work with at times. Cures in a few seconds with the UV light...I'll probably get more once I run out.
OK, I know.....
But they offer some neat stuff I thought some of you might like Unique Gifts & Innovative Products by Makers | The Grommet
ETA: Like this Liquid Bonder Kit by Bondic
Bondic works ok, adhesion is temporary to almost permanent depending on the substrate you are using. I found it acceptable to use for gluing a screen from the backside. The fact that it will come off with a little prying is a benefit there.
Good God almighty, what a PITA it was to order up a stock of silicone wire of various sizes in red and black! I spent so much time searching the net, every place I looked had so much out of stock that it was just ridiculous. Ended up having to order some off ebay, hobby king and amazon, the damn shipping for each order drove up the cost but at least I'll have some of each ranging from 12 to 22, I shouldn't need any for quite a while.
Then I go to order some more 510's, planned on biting the bullet and ordering a tap for them and SOB the taps are out of stock! UGH!!
Then I go to order some more 510's, planned on biting the bullet and ordering a tap for them and SOB the taps are out of stock! UGH!!
I had the shiny one in my cart for the longest time; I may just go for this one. Thanks Steamer!Anyone looking for a Good Deal!
I paid way too much for a black one like this. I put a DNA40 in it and it's been a great little mod.
So for this price I will have a silver one to. I just happen to have one small screen DNA40 left over from the Co-Op before the 200's
$32.26 Infinite ZERO Modz Styled VW Variable Wattage APV Box Mod - 7-40W / 1*18650 / stainless steel / grey at FastTech - Worldwide Free Shipping
Good God almighty, what a PITA it was to order up a stock of silicone wire of various sizes in red and black! I spent so much time searching the net, every place I looked had so much out of stock that it was just ridiculous. Ended up having to order some off ebay, hobby king and amazon, the damn shipping for each order drove up the cost but at least I'll have some of each ranging from 12 to 22, I shouldn't need any for quite a while.
Then I go to order some more 510's, planned on biting the bullet and ordering a tap for them and SOB the taps are out of stock! UGH!!
If anyone else needs some, I got 12 AWG silicone insulated red/black from Amazon. It was only about 4 bucks all in. Shipped directly from . . . you guessed it . . . China. I'm not positive if this was it but likely: http://www.amazon.com/niceeshop-TM-...261349&sr=8-3&keywords=12+gauge+silicone+wire
I'd guess since it shipped from China they'd ship anywhere free.
For the low current stuff, just about any 22 AWG wire will do.
You can do the dual 18650 now, I`m pushing for a DNA40 like new chipSo maybe a new chip in the near future? An addition to the Escribe Family
Another Co-Op? A single or Dual 18650 60 to 75/100 watt TC chip would be nice
Or maybe both a single 18650 60 watt and a dual 18650 100 watt TC Chip?
IMO they should utilize the 18650's everybody has them and the chargers
Would round out the Evolv family nicely
Speaking the 12, that's what I originally bought along with some 16 weeks ago for my first build. I wanted to use the 12 on the 510 as recommended but there was no way the jacket of the wire would fit through he hole in the bottom spring retaining cap of the VT 510 so I used the 16. I thought about making the hole in the cap larger but it would have been too big of a hole in the cap for that huge wire to fit through. Even though I'll never push it beyond what the 16 will handle I still want to change it out to the 12 later. I think I figured a way to do that by soldering a solid brass post into the 510 pin, have it extend down beyond the bottom cap then solder the wire to the pin. I may make the pin bigger where it extends out and either drill a hole in the bottom like the 510 pin hole or drill a hole through the side. Would most likely cover it with heat shrink, depending if there is any chance of it hitting something and shorting. I need to get more 510's to play with before I know for sure if the idea will work well.
I had ordered the BRD Squonk,,, twice and both times Sculpteo canceled the order. They said the size of something was not right. I PM'ed to @BlueridgeDog,, who promptly made changes on the design. But I had already ordered the one from Shapeways, and I was not gonna order from them again until the refunds made it back into my account. Funny thing about Sculpteo was that each time I ordered the item the price went up! Checked the price since BRD made the changes and it went up again. Really would like to hear about how the Sculpteo one turns out. I will post my findings on the Shapeways one, as it is supposed to ship tomorrow. With as slow as the parts co-op thing is moving who knows when mine will all come together!
Shapeways BRD squonk shipped was $72.09.
- Status
Similar threads
