I'm using a different charging board. Someone plz double check my logic? In step iv, I'll wire red to in+ and black to in-... Since i'm wiring the batter directly to the dna board, bat+/- won't be used on this charging board... Correct?
- Status
I'm using a different charging board. Someone plz double check my logic? In step iv, I'll wire red to in+ and black to in-... Since i'm wiring the batter directly to the dna board, bat+/- won't be used on this charging board... Correct?
View attachment 230637
I'm using a different charging board. Someone plz double check my logic? In step iv, I'll wire red to in+ and black to in-... Since i'm wiring the batter directly to the dna board, bat+/- won't be used on this charging board... Correct?
I'm using a different charging board. Someone plz double check my logic? In step iv, I'll wire red to in+ and black to in-... Since i'm wiring the batter directly to the dna board, bat+/- won't be used on this charging board... Correct?
I think you have it backwards, I would assume the in is the same as the usb input. But I haven't used that board.
Chornbro....great to see you out and about....it's been a while since we crossed paths.....good to see you into modding.....and the dna20d.....
bapgood is correct...you had it backwards.....batt +/- are your connections.....can't wait to see your finished mod.....
bapgood is correct...you had it backwards.....batt +/- are your connections.....can't wait to see your finished mod.....
Dang....mamu.....you are a busy gal.....how do you keep up with building all your mods and still have time to tutor....he-he....good to see ya here too as I don't post on the other forum......but I still read things there.....
Man I want to do this.
I solder extremely well
http://m73.photobucket.com/albumlist/lirrachus
Here's some of my work I did on game consoles.
Where are y'all getting the DNA 20d at?
Sent from my SGH-T999 using Tapatalk 2
I solder extremely well
http://m73.photobucket.com/albumlist/lirrachus
Here's some of my work I did on game consoles.
Where are y'all getting the DNA 20d at?
Sent from my SGH-T999 using Tapatalk 2
Thank you sir.
What tools are y'all using? I don't have access to big nice power tools. I only have nice soldering irons due to I'm not very mechanical.
Sent from my SGH-T999 using Tapatalk 2
What tools are y'all using? I don't have access to big nice power tools. I only have nice soldering irons due to I'm not very mechanical.
Sent from my SGH-T999 using Tapatalk 2
This thread may help you decide what tools to use.....you need more than just the soldering items...good luck....
http://www.e-cigarette-forum.com/forum/battery-mods/407083-modders-toolkit.html
Thank you. Exactly what I was looking for.
I have a dremmel was trying to figure out how to cut the 510 connection.
Any suggestions on batts and best/cheapest place to get them?
Sent from my SGH-T999 using Tapatalk 2
I have a dremmel was trying to figure out how to cut the 510 connection.
Any suggestions on batts and best/cheapest place to get them?
Sent from my SGH-T999 using Tapatalk 2
Most modders use a drill and metal cutting drill bit to drill the hole for the 510 connector...
Following this guide do we have to use the small buttons? I like a larger button for the firing.
Good to see u too! Hope all is well my friend. Appreciate the help, had a brain fart...
Got everything assembled and found one of the epoxied tac buttons was DOA... Really sucks! Im also getting an intermitten issue... Board acts like the "up" button is being held down. The push button isnt being pressed, nothing is grounded out, all bare wires are free and clear. Issue was intermittent,went away, now its back for good. Any ideas? Dont say bad board... Please...
My best guess on your "up button issue" is the button could be sticking...I had one do that a while back....are you using the small tactile buttons? I also had the epoxy seep into one button to where it wouldn't fire (just in case you run onto a button that won't push at all..) ya might try just pushing the button rapidly for a few seconds to see if it will free itself, but usually this does no good... or you could de-solder the up button and just touch the wires together to see if it increases the wattage reading up as it should....with the wires not connected to the up button you could also see if the up readings move on their own which may help you narrow down the issue should it continue..since all you connections are good and clear and if the button is good and not sticking, you might just e-mail Brandon as he is great to help with issues....later my friend... hope this helps....
Last edited:
- Status
