New Genesis type atomizer by DID!

[Matthew Shelbourn]

As I saw I have to do the lotery and open the Foto album
because I see all those fotos here!
Thank you
You know I love them!
DIDers.....(ha I like this)
Drip Tips/I had a finish problems with biger problem on satins
So I will run this asap!
I am learning from mistakes!
I will soon have the DID top caps with LOGO and SERIALS
and the 50% off will be given to the lucky first productions DIDers with no logo!
I give this because I wish all of you to have one!
I will do it for all the old ones!

Thank you

how do we know our did is from the first production?

Ben

 

[Jimi D.]

how do we know our did is from the first production?

Ben

How do we know if the air hole will match the wick?

 

[Darryll]

How do we know if the air hole will match the wick?

If you buy a top cap it comes with both parts.

 

[Jimi D.]

If you buy a top cap it comes with both parts.

Oh good! Thanks Darryll.

 

[fuzzione]

I use all mechanical and 3.7 w/IMR batts. One DID is wrapped with 30G and 4/5 wraps - the other is 32 G and 3/2 wraps - sometimes 4/3 wraps - no problem. Dont worry about ohms- I never check my ohms - I go by # of wraps and what tastes best. I think - IMO - people make too much of an issue on what their ohms are reading. It's all about the flavor first, vapor second. Just wrap the wire, check for shorts - if ok, then vape it.

You're probably right. Nonetheless, I seem to get a strange and unexplainable sense of comfort tapping my pv's ohm checker and seeing it's where it ought to be

 

[Unspokenzero]

Just ordered my DID I am excited! This will be my second RBA I have 2 smok vivi tanks wicked with ss mesh and they are awesome. I can't wait to tinker with this puppy and get it vaping like a champ..

Sent from my HTC Desire HD using Tapatalk 2

 

[yankeebobo]

Just ordered my DID I am excited! This will be my second RBA I have 2 smok vivi tanks wicked with ss mesh and they are awesome. I can't wait to tinker with this puppy and get it vaping like a champ..

Sent from my HTC Desire HD using Tapatalk 2

You'll go back for another....
Enjoy! And welcome to DID family!

 

[denali_41]

if i remember correctly ? the first run was only 75 units,jim had sent out an updated replacement center post

 

[barqs]

I was just about to ask about this as I didn't see it on the site as I was getting SS kit as well but will wait to pull the trigger when its up for 50% for top cap.

Thanks you pre answered my question!!

As I saw I have to do the lotery and open the Foto album
because I see all those fotos here!
Thank you
You know I love them!
DIDers.....(ha I like this)
Drip Tips/I had a finish problems with biger problem on satins
So I will run this asap!
I am learning from mistakes!
I will soon have the DID top caps with LOGO and SERIALS
and the 50% off will be given to the lucky first productions DIDers with no logo!
I give this because I wish all of you to have one!
I will do it for all the old ones!

Thank you

 

[barqs]

just to sure if I order a top cap with logo and serial # the serial # will be #1690 same as my order# correct?

All numbers start from 0101 but the owners will be as the order number! Fair!
the numbers of 0001 to 0100 will be soon in a Metal Box. All three together with the same number and on the box to!
100pcs Polished and 100pcs Satin.
The DID the Mini DID and the Gemini.
Do not know about signature.Will see your oppinion first!
Thank you

 

[tybin]

this will be soon? very cool

As I saw I have to do the lotery and open the Foto album
because I see all those fotos here!
Thank you
You know I love them!
DIDers.....(ha I like this)
Drip Tips/I had a finish problems with biger problem on satins
So I will run this asap!
I am learning from mistakes!
I will soon have the DID top caps with LOGO and SERIALS
and the 50% off will be given to the lucky first productions DIDers with no logo!
I give this because I wish all of you to have one!
I will do it for all the old ones!

Thank you

 

[Tonytiger1]

Better to pop the bottom teflon insert out and put the o-ring on the little end and then re-insert. I put one just on the end of the pin and didn't realize it was compressing every time I screwed it on which raised the bottom nut in the top cap enough to let condensation down the center tube. I noticed because I got a little leakage out the bottom. This will definitely extend the pin on the bottom, but be sure to retighten the bottom nut in the top can when it is on a device so it is tight even when compressed.

Great job. My post on my omega is ss. Im with you on the corrosion. That would be the reasons I would switch mime out. Now we are talking sense. The copper poisoning is just silly when it comes to the post issue. I breath jet fuel all day. Have ray tubes in front of me and sit at 37000 ft for 6-7 hours. Eat pink slime the list go on and on. You rock. The Did rocks. I get nic highs from it its so good. Unless some builds an Atty without a wick that runs at real low amps. I sticking with the did
How about one the spins a small magneto the uses high voltage to spark on to the wick. .


Tony

 

[Jim Damianidis]

how do we know our did is from the first production?

Ben

There are no logo and serial

if i remember correctly ? the first run was only 75 units,jim had sent out an updated replacement center post

Yes

just to sure if I order a top cap with logo and serial # the serial # will be #1690 same as my order# correct?

No
if the order before yours is let say #2689 and he got serial #0231 you will take serial #0232

I learned multi quote! lolol

 

[tybin]

what time is it in Greece Jim? I was going to say good evening but perhaps it is good morning to you?

 

[Uma]

Mini Vapor from my Mini

 

[Tonytiger1]

Mini Vapor from my Mini
View attachment 131691

Nice.


Tony

 

[Uma]

Updated center post? I missed that one somehow. Speaking of Center Posts though, I forgot to order mine! I'll have to do that for sure next payday.

@Jim.. it would be nice if there were an o-ring illustration available on your site. I had a heck of time remembering where the 2nd little o-ring goes...

 

[DukeBlue]

Updated center post? I missed that one somehow. Speaking of Center Posts though, I forgot to order mine! I'll have to do that for sure next payday.

@Jim.. it would be nice if there were an o-ring illustration available on your site. I had a heck of time remembering where the 2nd little o-ring goes...

I had the same problem when I got mine. I watched the YouTube review again from Igetcha69 that Jim has on his home page to figure it out.

 

[denali_41]

Updated center post? I missed that one somehow. Speaking of Center Posts though, I forgot to order mine! I'll have to do that for sure next payday.

@Jim.. it would be nice if there were an o-ring illustration available on your site. I had a heck of time remembering where the 2nd little o-ring goes...

updates post is stainless


for assembly vid,,go to the first page of this thread,jim does a build there

 

[misplacedsooner]

hi everyone. i just bought a did on classifieds and im sure im going to need some help with it. the guy said its new and doesnt even have the orings in it yet. im very inexperienced with rebuildables. i have 2 phoenix ones and have yet to build any coils and wicks so i may bomb you with questions. thinking i should order a clear tank for this? im a little intimidated by getting this but i think the payoff will be well worth it.