- Status
Well, one could not possibly be enough now could it?Another 3D on the way since Vaperev just stocked up on them. No matter what RBA I try (Genny style, Kayfun style, etc.), the taste just never comes close to a well built RDA. Can't wait!
For me, the 3D is really the best of both worlds... dripper plus tank. I absolutely love it and have used it daily since I got them.
I commute 2.5 hours a day so this will probably be my next aquisistion. The 3D looks friggin awesome and I've been contemplating a new RDA lately. The Nimbus is ok but not ideal.
Sadly I've blown my vape budget for for a little while after the 69...which is sitting in Cincinati already! Could tomorrow be the day of delivery??
CW, are those the anodized tubes, or some other kind of after-market refinishing?
Those are Eric's Editions. Petros came out at about the same time that the Nemesis was released with 3 heat treating custom finishes. Since then, he has added 2 more finishes. These are the only after market finishes created and partnered with Atmomixani.
Like I said on another forum... 4 down, 1 to go.
Jealous...
Those finishes look amazing. Anywhere to pick them up?
Sent from my EVO using Tapatalk
Sent from my EVO using Tapatalk
Jealous! They look absolutely gorgeous!
Definitely. I was amazed at how long I was able to vape off a .6 ohm dual coil without having to refill. And even then, if you run out just press the cap, dump another ml or so + about .5 ml that fit on the deck, and you are set. Truly a great innovative RDA.
These are Eric's Editions. Petros maintains a list that you can sign up on to get one. These are 4 of the 5 available finishes. He does amazing work and is incredibly busy so, if he doesn't reply right away give him a few days - he will.
Best thing to do is use the Contact link on Atmomixani's site and get his email address. I am not sure how long the wait is but, I know it is longer than 6 months at the moment.
I may be off base, but I want to think that the 3D is almost like a more modern bottom-feeder. Don't squonk; pump.
So I finally got the GP Spheroid V2 in hand, and unfortunately, it's completely unusable in either the Nemi, Nemesis, or 69 due to the location of the air intake hole on the 510 connector and the way these mods are designed to allow air intake through the top cap. Sad, because the Spheroid looks so nice on the Nemi...
EDIT: Looks like I can get air flow by unscrewing the Spheroid off the top cap a little bit to allow a bit of air space between the base and the top cap. The downside to this is that it puts more stress on the 510 connector... and the unsightly gap.
I'll see if I can get my hands on a spare Nemi top cap or a Spheroid base cap to add air channels to it so that air can reach the base while fully screwed together.
EDIT: Looks like I can get air flow by unscrewing the Spheroid off the top cap a little bit to allow a bit of air space between the base and the top cap. The downside to this is that it puts more stress on the 510 connector... and the unsightly gap.
I'll see if I can get my hands on a spare Nemi top cap or a Spheroid base cap to add air channels to it so that air can reach the base while fully screwed together.
Last edited:
Atmomixani's "Iced" products have (an) extra cut(s) around the circumference. As far as I understand it, the purpose is decorative, although, it does increase surface area. One could say it acts as a heat sink. Maybe that's why it's "iced"? Because it cools faster?
Iced versions have the 3 lines/coolers to the upper part..
So Shined Ice for Nemesis for example is this
when Shined for Nemesis is this
So Shined Ice for Nemesis for example is this
when Shined for Nemesis is this
So, I've been using the 'beater' at work the past week or so. I finally rebuilt the Kayfun (which is on the Nemesis) and vaped some Five Pawns 'Castle Long Reserve' tonight. Really makes me appreciate the Nemesis - by far my favorite setup. 18500 mode with Kick 2 @ 15W and 18350's.
As CannedWolf is aware, I talked a co-worker out of buying a clone, which a local vape shop tried to sell him (and he almost spent way too much for a crap clone). While he cannot afford a Nemesis, it's on his radar. In the meantime, he's going to get a cheap mod such as the Magneto. He hasn't decided yet, but I opened his world to all the different choices. He didn't know there were mechanical mods with side buttons, and will likely end up getting a cheap one with side button, since that's what he's used to. When the time comes, I bet he doesn't get a Nemesis, but rather a 69. Times are tough though - his wife just lost her job on Friday, and their medical insurance was through her job.
As for me, the 'beater' will be going to the desert with me next weekend, where it may not survive the trip. Lots of alkaline dust in the air that eats away at metals. It still has its intended purpose. However, I do have a 'want list', which includes a VW Nemesis, brushed Loki v2, brushed 3D, whatever Atmomixani comes out with for a hybrid Nemi, and turquoise Nemesis tube (and eventually all the other parts to build a 3rd Nemesis). Tax return is coming soon - most of which will pay for the balance on my wife's surgery, but hopefully enough spending money left over to get some Atmomixani parts.
Someday I'll have a collection like some of the more fortunate folks on this forum. 'Till then...
As CannedWolf is aware, I talked a co-worker out of buying a clone, which a local vape shop tried to sell him (and he almost spent way too much for a crap clone). While he cannot afford a Nemesis, it's on his radar. In the meantime, he's going to get a cheap mod such as the Magneto. He hasn't decided yet, but I opened his world to all the different choices. He didn't know there were mechanical mods with side buttons, and will likely end up getting a cheap one with side button, since that's what he's used to. When the time comes, I bet he doesn't get a Nemesis, but rather a 69. Times are tough though - his wife just lost her job on Friday, and their medical insurance was through her job.
As for me, the 'beater' will be going to the desert with me next weekend, where it may not survive the trip. Lots of alkaline dust in the air that eats away at metals. It still has its intended purpose. However, I do have a 'want list', which includes a VW Nemesis, brushed Loki v2, brushed 3D, whatever Atmomixani comes out with for a hybrid Nemi, and turquoise Nemesis tube (and eventually all the other parts to build a 3rd Nemesis). Tax return is coming soon - most of which will pay for the balance on my wife's surgery, but hopefully enough spending money left over to get some Atmomixani parts.
Someday I'll have a collection like some of the more fortunate folks on this forum. 'Till then...
- Status
Similar threads
