NEW YIHI SX MINI ML CLASS!
- Thread starter smokyribs
- Start date
- th_trl_thread_readers 0
- Status
Reinstall the upgrade. Make sure you see UPGRADE FINISHED.Not work at all
When i input the battery is not shown the logo of sx mini .. help
It will after that. Speaking from experience.
Sent from my iPhone
Saw you are a new ECF member..welcome... you came to the right thread with your issue.....there are some very knowledgeable SX folks here that should be able to help you. Hopefully your device will come back to life with the assistance/guidance of them. If not.... warranty.....
Good luck....
Saw you are a new ECF member..welcome... you came to the right thread with your issue.....there are some very knowledgeable SX folks here (I'm not one of them) that should be able to help you. Hopefully your device will come back to life with the assistance/guidance of them. If not.... warranty.....
Good luck....
Thank u
And i wish my problem will be solved soon
If you haven't already tried a different battery, you should (making sure you are observing proper polarity). I don't currently have one, but I wonder if there is a stealth mode that could possibly be causing the problem. If neither of those are the cause, it sounds like you might need warranty service. Good luck!
Cheers,
Steve
Cheers,
Steve
Last edited:
A couple of other things to try, a new battery, leave the battery out for a few hours.
Ok I'm trying to get setup for when ML arrives I go to YiHiecigar>SXI-Q>SXIpackag.x64 copy mscvr110d.dll paste to windows>System32 correct
That is just one of the steps if you have an x64 Windows 10 system. You need to follow step by step in the PDF. The dll is in the installation folder after you do the installation and before you load the driver.
If you mean after I have installled the program I did that and changed it to Win7 compatibility. I take it after I do the copy and paste then I can run the USB driver installation in the same file and it should install the driver. I have to make a change in the properties to run as administrator but that will manually install the driver on my ML correct.
But the ML has Ni, Ti modes on the mod correct so I don't have to use the sw.
I would imagine that the way they are getting pounded in the Maryland area things aren't going to be moving too fast for a week or so. Talking up to 3' of snow.
Hi everyone. This is a long post but it is about temp control.
I've been enjoying my sx ml in kanthal mode. However i've recently tried to put it into joules mode with a nickel build. 0.10ohm, 420f at 20w. However, the mod fails to read my resistance. The resistance just stays at 0.00ohms and it keeps saying my coil is dry. I've tried various builds, various RDAs/RTAs with nickel and i get the same result.
I have ruled out a bad build as the same build and tank fires fine in temp mode in my DNA200 devices.
I have ruled out a bad 510 connection as the sx fires my coils in kanthal mode just fine.
I have the latest software running, and have reinstalled the software several times.
I have tried various adjustments; changing the wattage, increasing temp control to max temp, manual entry of TCR, increasing/decreasing temp compensation.
I am at a loss. What is going on? Why can't my mod read the resistance of my temp builds when it is working fine on my other temp devices?
I appreciate you reading and hope to have a solution asap as i usually vape with temp protection.
I've been enjoying my sx ml in kanthal mode. However i've recently tried to put it into joules mode with a nickel build. 0.10ohm, 420f at 20w. However, the mod fails to read my resistance. The resistance just stays at 0.00ohms and it keeps saying my coil is dry. I've tried various builds, various RDAs/RTAs with nickel and i get the same result.
I have ruled out a bad build as the same build and tank fires fine in temp mode in my DNA200 devices.
I have ruled out a bad 510 connection as the sx fires my coils in kanthal mode just fine.
I have the latest software running, and have reinstalled the software several times.
I have tried various adjustments; changing the wattage, increasing temp control to max temp, manual entry of TCR, increasing/decreasing temp compensation.
I am at a loss. What is going on? Why can't my mod read the resistance of my temp builds when it is working fine on my other temp devices?
I appreciate you reading and hope to have a solution asap as i usually vape with temp protection.
If it doesn't turn on when you plug it into your computer, then I think you bricked it and need to send it back to the vendor for a replacement.
The file they have highlighted is a batch file COPY_MSVCR110D.Bat that if run will copy the msvcr110d.dll file into the destination location for you. I don't think the instruction is really clear in telling you to run it so I can imagine many people copying and pasting the msvcr110d.dll manually from source to destination folder or perhaps even copying the COPY_MSVCR110D.Bat which would be of no use. It was a really easy process for me on Windows 7 but I can easily understand some will have difficulty.
Yes, but just run as administrator, no property change for that.
That is true @Vlad1. They are pointing to the dll but you really need to run the bat file and it includes a registry registration for the dll.
Wow, I missed that in the instructions too. I copied and pasted the drivers to their location. Oh well, it still worked.
- Status
Similar threads
- Locked
