Nuppin'
- Thread starter Spydro
- Start date
- th_trl_thread_readers 0
- Status
My Nuppin was in my mailbox when I got home, talk about fast!!! Ordered on Friday and arrived Monday! Peter must send by missile!
Excellent quality. Machining is superb, the way all the sleeves fit etc. Hefty weight ,Hits like a freight train! I normally do a 7 wrap .97ohm coil but I remember FB saying it hits harder so I added a wrap and with the slightly longer leg on the positive post it came out to 1.25 ohm and it hit harder and produced even more vapor and flavor than my .97 ohm build. So now I just need to spend some time fiddling with coil position and afc cap to hit my sweet spot. At first I had the coil close to the deck like I do with my RM2 but meh results. Lifted to about even with the airholes and did vape better but it seemed high off the deck and my 2mm RxW was sitting high. I made a sightly longer "tail" and slight tilt of the coil so the wick wouls sit on the deck and soak up the juice. It worked better but found myself needing to squonk harder to get the juice up there. I'm sure I find my spot just need to fine tune. I want to master my single coil build on this before even thinking about duals right now.
Excellent quality. Machining is superb, the way all the sleeves fit etc. Hefty weight ,Hits like a freight train! I normally do a 7 wrap .97ohm coil but I remember FB saying it hits harder so I added a wrap and with the slightly longer leg on the positive post it came out to 1.25 ohm and it hit harder and produced even more vapor and flavor than my .97 ohm build. So now I just need to spend some time fiddling with coil position and afc cap to hit my sweet spot. At first I had the coil close to the deck like I do with my RM2 but meh results. Lifted to about even with the airholes and did vape better but it seemed high off the deck and my 2mm RxW was sitting high. I made a sightly longer "tail" and slight tilt of the coil so the wick wouls sit on the deck and soak up the juice. It worked better but found myself needing to squonk harder to get the juice up there. I'm sure I find my spot just need to fine tune. I want to master my single coil build on this before even thinking about duals right now.
Not my coil design! I did not know it had been tried before, but plenty of others had built one of these before me... I just put one on the Nuppin, because it made sense.
Need to get a DNA40 built so I can make one of these out of Ni200.
Sent from my SGH-T889 using Tapatalk
Carole, does the atty screw down flush on your grand? If so, you might have to raise the 510 pin just slightly. You can do this by pushing up on it gently from the inside of your grand.
Really? Yes it does sit flush I think. How do you push up on it with that part in the way on the inside? You know, the part that goes across the top where the squonk tube goes through. You have to remove it?
Is this on the grand that Rob milled down for you? If so, it might not have been milled enough. It might just be off a very slight amount and it wouldn't matter then. To push up on the pin, you could do it by just removing the bottle and gently grab the tube and pin where they meet and push very gently up. You really won't feel it move as it is just a very slight amount, but may be enough for it to make contact. The other alternative would be to pm Peter to get instructions as to altering the 510 pin in the atty.
Thanks for your help. I saw what pdib wrote also. I will give it a shot and if it doesn't work I will try the other method. The one it won't work on is my newer TRA. The one it does work on is the one I had to send back to have milled, the black wrinkle.
Well that's what I get for being absent too long. A cool new bf atty shows up.
Just got my order in.
Just got my order in.
When I first set up my Nuppin, it wouldn't fire either. I ended up using a screwdriver and twisting the firing pin at the base of the atty about a 1/4 turn out. Worked.
I wound up having to turn it quite a bit. Got a little worried I was going too far with it, so I got a big screwdriver and turned the 510 on the Reo a hair. That did the trick! Thanks MH for your help. It's firing away on the TRA now. I am taking it with me to a concert tonight.
Yes I'm. If you look there are three internal holes, two directly across from each other so both are active. Then the third is between them so that only one outside hole is open the other is completely blocked. Pull the cap and look inside.Thanks Spydro. I went ahead and built from what I could tell from the pics. My coil came in at 1.4. I can try another later, but it's working and it's awesome! You guys aren't blocking the second airhole on a single build right? You just bring the holes down to a smaller opening?
Only one major problem.. it won't fire at all on my TRANot sure why. I had to swap it back to the black wrinkle to get it to fire. It's not making a connection...no O-ring underneath.
I liked my Nuppin' so much I got another one while the going was good
They do certainly pack a punch I have found. I use a single coil in mine at about 1.3 ohms and have been using my Reo's bareback with them (no kick!).
It is a bit of a mystery though - I have other atties with a smaller chamber, but for some reason the Nuppin' seems to give a bit more wallop than them. It must be fluid dynamics or something
They do certainly pack a punch I have found. I use a single coil in mine at about 1.3 ohms and have been using my Reo's bareback with them (no kick!).
It is a bit of a mystery though - I have other atties with a smaller chamber, but for some reason the Nuppin' seems to give a bit more wallop than them. It must be fluid dynamics or something
I liked my Nuppin' so much I got another one while the going was good
They do certainly pack a punch I have found. I use a single coil in mine at about 1.3 ohms and have been using my Reo's bareback with them (no kick!).
It is a bit of a mystery though - I have other atties with a smaller chamber, but for some reason the Nuppin' seems to give a bit more wallop than them. It must be fluid dynamics or something
I found the same thing! Getting great punch at 1.25 ohms vs. .95 on my other atties. Great warmth and flavor. I'm thinking with no negative posts sticking up all over the place and short positive post there is more airspace within the chamber and airflow different as it must swirl around inside more uniformly? Just a guess.
This thing is like a tailor made suit vs. off the rack. You can tweak it in so many ways, single or double coil, coil height, afc cap etc. and each tweak you can tell the difference right away! I'm liking it.
6 ml through a Nuppin' last night. I never do that. Peter is a genius - these atties suit a reo so well and it's like this thing is glued to my hand with this topper.
- Status
