OBS Engine NANO RTA

[mjag]

I got my set of Bondhus from ebay, best price I could find

Sent from my SM-N910P using Tapatalk

 

[Vaperx]

Got mine in. Having some learning curve issues. Been a dual coil temp control 316l vapor for some time. Going single coil has thrown me for a loop. My typical temp sweet spot was 420 deg. With a simple 8 wrap I think it was 3 mm .53 ohm I can't go above 13 watts without bouncing off the temp control and my evic mini throttling it back to like 8 watts. Pretty weak vape at the moment. Tried a 2mm coil and it was even worse.

Any 316l temp control non Clapton coil people out there that can tell me about their build.


Sent from my iPhone using Tapatalk

I go back and forth between SS Clapton and 26AWG 316L. I have done an 9 wrap 26AWG and vape at 425F and watts are at 30. I use a dna and Temp is dominant. I have no problems at all. I don't have to pay attention to watts really as that is just the ramp up to get to the desired temp. Once I hit 425 it holds steady around there and watts drop right off. This is only within 2 secs. Once I take another hit and coil is still hot watts are irrelevant as I'm close to the desired temp once again.

 

[ricks]

I'm really amazed with the smaller coils in these. Both my liquids are tasting better. I am blown away...

 

[janne303]

I'm really amazed with the smaller coils in these. Both my liquids are tasting better. I am blown away...

Hmmm. Maybee I need to test this out to

Wanna share pics of the wicking?

Skickat från min SM-G935F via Tapatalk

 

[kiba]

The board on that therion is mounted slightly off center, I only notice bc I just sent one of mine off to them to fix the same thing

 

[pahick]

I'm really amazed with the smaller coils in these. Both my liquids are tasting better. I am blown away...

What amazed me when I put the 2mm in, is just how well it still wicked. I mean pop pop pop...it just keeps wicking like a ....! So simple.

 

[ricks]

Hmmm. Maybee I need to test this out to

Wanna share pics of the wicking?

Skickat från min SM-G935F via Tapatalk

I'm currently just using a simple build in both mine. They're about a 2mm coil with 8 wraps of 28g SS wicked with Japanese cotton. The coils are sitting centered between the post holes and as close as possible to the poles without touching. It is So much better than my 3 and 4mm coils.

 

[KenD]

Installed a 2 mm coil in mine as well and I have to agree, it's even better.

Sent from my K6000 Pro using Tapatalk

 

[leekeylee]

2mm coils? think I'll have to try this.

I have been using 3mm inner diamater with 4x twisted SS 28 gauge 6 wraps 0.25 ohms running at 36watts and getting a nice vape. let's see if the flavour is better with 2mm

 

[ricks]

2mm appears to be the size coils these require. It just makes these Engines so much better and I still can't believe they could have gotten better. These are definitely the BEST tanks I have used.

 

[KenD]

Got mine in. Having some learning curve issues. Been a dual coil temp control 316l vapor for some time. Going single coil has thrown me for a loop. My typical temp sweet spot was 420 deg. With a simple 8 wrap I think it was 3 mm .53 ohm I can't go above 13 watts without bouncing off the temp control and my evic mini throttling it back to like 8 watts. Pretty weak vape at the moment. Tried a 2mm coil and it was even worse.

Any 316l temp control non Clapton coil people out there that can tell me about their build.


Sent from my iPhone using Tapatalk

I'm using a 2 mm 26 ga ss316l coil in mine. Don't remember the wrap number but the resistance is .602Ω. Works great at 220℃ and 50w.

Sent from my K6000 Pro using Tapatalk

 

[Bakseated1]

Contact or spaced coil on the 2mm simple coils


Sent from my iPhone using Tapatalk

 

[ricks]

Contact or spaced coil on the 2mm simple coils


Sent from my iPhone using Tapatalk

I use spaced coils

 

[ShowerHead]

Well, as soon as the lovely coil assistant gets home, it's off to 2mm town for me.
Sounds logical for this tank, but the proof is in the puffing, to mangle a phrase.

 

[Herrick]

Damn it. I ordered the regular Engine instead of the Nano. Dual coil I made the attempt to build and I got an atomizer short so I'm not even going to bother anymore. I really don't have the patience for this.

On the bright side, I got to see how bad these look on my little eLeaf Ipower 80. So I'm ready for that when the Engine Nano comes in from Subtank Supply. Are there any good high-capacity internal battery mods that will look ok with these 25mm tanks?

 

[Nailz]

Seen this tank a few times, but not taken much notice of it, as I am a MTL vapor and thought this was a tank made for sub ohming, but now I see @ricks is here, and knowing he is a MTL vapor too, I am now very curious about this tank and think I am going to give one a try, think it is a really good looking tank.

Any US vendors have this right now?

 

[Heartsdelight]

Seen this tank a few times, but not taken much notice of it, as I am a MTL vapor and thought this was a tank made for sub ohming, but now I see @ricks is here, and knowing he is a MTL vapor too, I am now very curious about this tank and think I am going to give one a try, think it is a really good looking tank.

Any US vendors have this right now?

Subtanksupply

 

[Nailz]

Subtanksupply

Thank you, was lucky they only had 6 black ones in stock, now only 5 left

 

[ricks]

Seen this tank a few times, but not taken much notice of it, as I am a MTL vapor and thought this was a tank made for sub ohming, but now I see @ricks is here, and knowing he is a MTL vapor too, I am now very curious about this tank and think I am going to give one a try, think it is a really good looking tank.

Any US vendors have this right now?

Best MTL tank I have ever used... Best tank period

 

[Nailz]

Best MTL tank I have ever used... Best tank period

Seen you say that a few times on different tanks

But is you say it is good, then that is enough for me to give it a try