Official ProVari 3 Thread - P3
- Thread starter Vape360
- Start date
- th_trl_thread_readers 0
- Status
MODS - I asked Tim if I could announce his intentions to the P3 thread and he gave me permission.
This seems to be following the rule about e-mails being private, need permission, etc. Please PM me if not. Thanks.
**************************************************************************************
It might be early to think about sleeving your P3 but here's the 411 if you want to wrap that rascal:
I asked Tim at SerenityGear Leather about sleeves for the P3 and he said -
"It's very hard to say when I will have something up on the site for the P3.
I typically only have an hour or two to spend on leatherwork in the evenings, so it may be a while - maybe early December?"
Tim Brown
SerenityGear Leather
sales@serenitygear.com
This seems to be following the rule about e-mails being private, need permission, etc. Please PM me if not. Thanks.
**************************************************************************************
It might be early to think about sleeving your P3 but here's the 411 if you want to wrap that rascal:
I asked Tim at SerenityGear Leather about sleeves for the P3 and he said -
"It's very hard to say when I will have something up on the site for the P3.
I typically only have an hour or two to spend on leatherwork in the evenings, so it may be a while - maybe early December?"
Tim Brown
SerenityGear Leather
sales@serenitygear.com
After messing with this menu and notwithstanding the sheer agonizing torture that Busardo goes through using it, I find auto scroll to be no big problem.
Busardo had me getting dizzy. I was getting a headache and going cross eyed.
For the particular juice I'm vaping it is exceptional. I prefer the juice I am vaping to be cooler. Just tastes better. Have 28 gauge wire at boost setting B2. I think I prefer it more than the 26 gauge set up I had...again, for this particular juice. I have other flavors I prefer at warmer temps. That RCL feature will come in handy.
BTW, my IQ is 96. Guess I don't have much room to complain, huh?
I like Busardo a lot, but I thought he went overboard in his disdain for the P3 menu system. Good grief, putting the toilet seat up after my wife causes me more stress than this auto-scroll menu.
Last time I checked the IQ was at 124
Wait, I don't have a P3 yet...
lost points obviously
Wait, I don't have a P3 yet...
lost points obviously
Is this Boost error that everyone is talking about a heat/temp error or high wattage? I see people posting what ohms and wattage they are using but what type of coils are being used? Could it be cause by material used for the coils causing more heat?
Not sure MTF. Still trying to figure it out myself. I just got the thing. It doesn't say the type of error that I can tell. Just flashes an alert. I'm finding it hard to believe it would be high wattage. I set mine at 8.5 watts with 2.3 ohms and it wont boost. Actually, I'm kind of disappointed about that.
From the manual.. It's the serial number..
Since the display can only show certain characters.. They split it up in 3 .. Lol
It jacks up the watts/voltage for certain time to get the coil hot quick,
HotShot Boost mode allows you to get more vapor with a short power boost with each puff. This setting is adjustable allowing you to dial-in your favorite boost time setting (.25 to 1.25 seconds).
You mean the SN is 18 characters long? That's a serial number for each molecule!. It's a Provari, not plankton!
After few hours of vaping. I lov p3! I have set the same setting as my 2.5.. It seems I get more cloud on p3.
Kraken.. Single coil @ 1.9 ohms.. 3.8 volts. Boost set to 1. Wowza.. Had the bedroom in cloud after few mins.. Lol
Kraken.. Single coil @ 1.9 ohms.. 3.8 volts. Boost set to 1. Wowza.. Had the bedroom in cloud after few mins.. Lol
- Status
Similar threads
- Locked
