Official ProVari 3 Thread - P3
- Thread starter Vape360
- Start date
- th_trl_thread_readers 0
- Status
I should have the new end piece tomorrow as it is shipped. I can't wait and love the design, very classy and good on the company to give some proceeds to a cause of the clients choosing.
That being said, I dropped off my original P3 end piece (small spring one) at a local trophy shop that does lazer engraving. I gave them this Vector file as well. As I am new, I see a lot of haters and I can't wait to show a pic of me vaping with the Koolaid. I'd almost rather the pitcher be holding a vape, but I don't know how to alter or make the file to email.
That being said, I dropped off my original P3 end piece (small spring one) at a local trophy shop that does lazer engraving. I gave them this Vector file as well. As I am new, I see a lot of haters and I can't wait to show a pic of me vaping with the Koolaid. I'd almost rather the pitcher be holding a vape, but I don't know how to alter or make the file to email.
Yep! Provari v1, v2, and v2.5 all have the same end cap design.
Battery "Empty"
3.4v
AW IMR 18490, 1100mAh (from 10/6/14...second of two batteries from this batch). Forgot to read IQ. Oh well.
3.4v
AW IMR 18490, 1100mAh (from 10/6/14...second of two batteries from this batch). Forgot to read IQ. Oh well.
Hey, has anyone gotten some No-Ox? I just got mine today (along with a car cup holder for my Provari's) from Provape. Anyway, the No-Ox (no I haven't used any yet) comes in a plastic tube that appears you just take scissors and cut the squeeze from side off. But once you've done that, there doesn't seem to be anything to keep it sealed.
So, I'm wondering if anyone has gotten a tube from Provape and if you did, what did you do with it after opening it. I don't want the stuff to dry out (if it even can dry out?).
Vape360: If you see this, could you comment? I need to know these things before I accept your kind offer to come work for you. Yes I do!!
Ps: Of course I ordered the two items just 3 days ago. Bad timing on my end. Had I known a Provarinati end cap would be offered just yesterday, I would have included one. I'll just have to add one to my next order.
So, I'm wondering if anyone has gotten a tube from Provape and if you did, what did you do with it after opening it. I don't want the stuff to dry out (if it even can dry out?).
Vape360: If you see this, could you comment? I need to know these things before I accept your kind offer to come work for you. Yes I do!!
Ps: Of course I ordered the two items just 3 days ago. Bad timing on my end. Had I known a Provarinati end cap would be offered just yesterday, I would have included one. I'll just have to add one to my next order.
Last edited:
Yes, you could always zip it. Don't know that I've ever left one open but I'll give it a try and see what happens. It might take some time to run this experiment.
Yes, you could always zip it. Don't know that I've ever left one open but I'll give it a try and see what happens. It might take some time to run this experiment.
Lol...
Knowing me.. I'm a messy guy.. Stuff in that kind of container ends all over the place... Hence I suggested ziplock. Hehe
Well, they sent it in a ziplock bag, but even then won't it be subject to drying out in that bag? There's no seal on the tube whatsoever.
This is the tube:
Last edited:
If you are handy, you might be able to reseal it...
1) squeeze the stuff toward the bottom
2) lay it down flat on a hard surface
3) put down a paper towel over the open end
4) press on the open end with a hot iron(like you iron your clothes with)
The paper towel will act like a buffer to keep the iron clean, and the iron will(if you do it right) heat seal the end closed, much the same way a vacuum sealer works.
Well, they sent it in a ziplock bag, but even then won't it be subject to drying out in that bag? There's no seal on the tube whatsoever.
This is the tube:
Ah.. Didn't know it came with ziplock.. Oops.. Lol
Yes, you could always zip it. Don't know that I've ever left one open but I'll give it a try and see what happens. It might take some time to run this experiment.
I got something similar for my V3 Flip. Clip the tip; use it; lay it down; never leaked.
Haven't got the No-Ox yet to try.
OK...Vape 360? Is this the same stuff?
Because...if it is it is grease. Grease does not dry out in my experience because it is oily...Maybe over many years but not in a year.
ETA: This is the same stuff judging from the picture above...I am going to just buy a tub of it and that way I know it will be sealed and last an age.
FYI Amazon also carries Koh Gen Do cotton pads. You can get a life time supply very cheaply there.
Because...if it is it is grease. Grease does not dry out in my experience because it is oily...Maybe over many years but not in a year.
ETA: This is the same stuff judging from the picture above...I am going to just buy a tub of it and that way I know it will be sealed and last an age.
FYI Amazon also carries Koh Gen Do cotton pads. You can get a life time supply very cheaply there.
Last edited:
I've never used primer puffs… except on the auto-battery 510 I built for my wife. But then I don't vape into my lungs either (pipe/cigar smoker).
So... you swear you didn't inhale...either??!
Yes, you could always zip it. Don't know that I've ever left one open but I'll give it a try and see what happens. It might take some time to run this experiment.
I'm going to lube my threads (doesn't that sound comical?) tonight. After I open the tube, I'll tape it shut, then put it in the ziplock bag you guys sent it in.
I have the same charger and yes, they stop charging when the green light is on. I am a bad boy and leave my batteries in the charger til next needed (might be 1-2 days) no damage in 1+ years
Well, they sent it in a ziplock bag, but even then won't it be subject to drying out in that bag? There's no seal on the tube whatsoever.
This is the tube:
If you squeeze as much air out of the bag as possible, before zipping shut, you shouldn't have to worry too much.
- Status
Similar threads
- Locked
