Beep!!! How did u put claptons on the W? 1mm diameter or something? I want try it but no idea what diameter it can take. Currently to twisted St 3mm.
Bhoot
Official Squape R[eloaded] thread!
- Thread starter brickfollett
- Start date
- th_trl_thread_readers 0
- Status
Bhoot
I haven't run anything but Ni200 on mine since I got it last November & it's really the only atty I've used since then.
I agree the pin is a pain but I've learned to deal with it by looking at it as if it allows an adjustable resistance. I know 8 wraps of .30mm (28/29 gauge) Ni200 should be around 0.13. Pin out further will get a lower reading, in in 1/2-1/4 turns might increase it in 0.01 ohm increments. It can be annoying for sure but it's what I've grown accustomed to. I just use the tip of my fingernail to adjust it which makes doing it a lot easier on the fly than when I originally had to use a screwdriver each time.
I agree the pin is a pain but I've learned to deal with it by looking at it as if it allows an adjustable resistance. I know 8 wraps of .30mm (28/29 gauge) Ni200 should be around 0.13. Pin out further will get a lower reading, in in 1/2-1/4 turns might increase it in 0.01 ohm increments. It can be annoying for sure but it's what I've grown accustomed to. I just use the tip of my fingernail to adjust it which makes doing it a lot easier on the fly than when I originally had to use a screwdriver each time.
Has anybody with center pin issues that replaced it experience an improvement? It is annoying and I'm tempted to buy a new pin but part of me feels like it won't change anything.
I had my ohms jumping around and eventually stopping getting an ohm reading. New pin fixed it instantly. Also I now unscrew the 510 pin every so often and give the pin and opening a good cleane with some tissue.
Update. Tried plain Clapton dual coil on the D deck. Voltage is her and liquid is burning quicker but feel a single 3mm fused Clapton 4/5 wraps at 0.5ohms tastes a lot better to me and liquid lasts longer. Might not be as intense with a single coil but have a marquis RDA when I need an intense hit.
Bhoot
Last edited:
Browsing the StattQualm website i found this. "For those that want a little more" (as if it wasn't tall and heavy enough!)
Works with both the R and Rs, Unlimited stackability! We're talking meters and liters now people
Made me chuckle
Works with both the R and Rs, Unlimited stackability! We're talking meters and liters now people
Made me chuckle
Last edited:
I know, I saw that just now when I was looking at replacing pins & possibly a new bell- then I saw the shipping (20 EU!).
The normal full-sized R is almost too large in my opinion, but can't bring myself to use anything with a smaller juice capacity.
The normal full-sized R is almost too large in my opinion, but can't bring myself to use anything with a smaller juice capacity.
Exactly what I was looking for! Their shipping is a little strange, for just an Rs chimney shipping is ~$9. Add anything to the order and it jumps up to ~$23.
What coil for B deck?
I am currently using Ti 24G, 6 wraps ID 3mm, on my SX Mini M with TC, Joule reads 12 and at 390F I think the vape is too strong and flavor isn't good for my liking, less than Rose V2S and Kayfun V4. No leaking or gurgling which is good.
If I want more flavor, how do I change/adjust my coil? Thank you.
I am currently using Ti 24G, 6 wraps ID 3mm, on my SX Mini M with TC, Joule reads 12 and at 390F I think the vape is too strong and flavor isn't good for my liking, less than Rose V2S and Kayfun V4. No leaking or gurgling which is good.
If I want more flavor, how do I change/adjust my coil? Thank you.
@javyn The B Deck definitely provides a juicier vape, especially with the full R. imo the W deck works much better with the Rs since the chimney bell doesn't go so far down the sides of the deck, freeing up juice flow to the wick. The B deck has the juice holes so far down on the deck the chimney on the full R doesn't affect it. Added bonus (!) The B deck really vapes down to the last drop of every tank - and there's enough saturation and wick that (so far) I've noticed the flavor change every time before it's too late.
For W deck wicking this is a fool-proof trimming method (just no tucking into vertical channels) that I've been using since I got my Squape and I've never had a problem.
For W deck wicking this is a fool-proof trimming method (just no tucking into vertical channels) that I've been using since I got my Squape and I've never had a problem.
Last edited:
Well, sorry for my ignorance. I had been using W, but B is much better, after I started using B, W stays in my drawer forever even since. However, I believe B could be even better, just don't know how. I have Rs by the way.
Oh, and wicking was perfect either W or B. Only the flavor seems not as good as my other atties, with B slightly better than W, I hope I can improve it since sqrs is so much better than others in terms of build/wicking simplicity, and gurgle-free...
Oh, and wicking was perfect either W or B. Only the flavor seems not as good as my other atties, with B slightly better than W, I hope I can improve it since sqrs is so much better than others in terms of build/wicking simplicity, and gurgle-free...
Last edited:
Oh I agree, in either case the B deck gives a better vape vs. the W, especially if you want to get up over 20W+.
Sorry I cannot suggest builds with Ti wire, I have yet to try anything but Kanthal so far. My favorite right now is a single 26ga A1 contact coil around 2.7mm bit, anywhere from 9 to 12 wraps. Easy to build, great performance, never dry hits
Sorry I cannot suggest builds with Ti wire, I have yet to try anything but Kanthal so far. My favorite right now is a single 26ga A1 contact coil around 2.7mm bit, anywhere from 9 to 12 wraps. Easy to build, great performance, never dry hits
Jam some silicone wire strands in the threads and the resistance issues are 100% fixed. You can also use some 30g ni200. Fix that center pin and the issues with resistance will be gone. I posted this solution many many pages ago.
this very much depends on the juice for me. I find the Squape has sometimes highlight flaws in juices. For instance, if the juice is too sweet in my dripper it's going to be unbearable in the Squape. If a juice tends to be dry it wont do well in my squape. If a juice is too heavy on one flavor or there is come flavor in the juice I do not like - in the squape that will probably be all I will taste. Flavor is always a step under my drippers but well balanced and really "smooth" juices are very satisfying. I also like to run complex flavor profile juices through my squape as (when they're good) the squape provides a variable kind of vape where subtle differences in the vape come out on each draw.
The juices that don't do well in the squape rarely (if ever) make it on my reorder list for my drippers either ...
Where did you find the bell cap, please?The Mini's getting a bit banged up but the new Rs bell cap looks and vapes great!
I ordered from c9v. They are also available directly from StattQualm.
I'm kicking myself for not adding a spare Rs chimney and a spare 510 pin to my order. I guess i'll just have to order another base to justify the shipping!
I'm kicking myself for not adding a spare Rs chimney and a spare 510 pin to my order. I guess i'll just have to order another base to justify the shipping!
- Status
