Last edited:
Orion V2 roll call
- Thread starter tierrataz
- Start date
- th_trl_thread_readers 0
- Status
Hi Ob,
don't know what you are looking for: negative and positive switches
People have been modifying the posts with different screws and such. I have seen one and the other. I am thinking about doing both and was hoping for a list of all that was needed to do both.
ah ok got ya! all I know is that the DID brass nuts where used for the positive pole and or m2 size nuts stacked on top of each other. For the negative screw, I think just the same as is there now but longer and an extra nut, this to raise the coil more.
Sorry can't be of more help then that, I am sure somebody will chime in.
Yes, I think it plays a large roll in the flavor department.
@Brian, I haven't tried a DID... and am waiting on the DID-mini to get here...
Not the case at all tierrataz
It vapes nice. I don't get a hot vape nor punching TH. I get a nice warm vape, and TH is more dependent on the liquid IMO. Maybe, that person (I don't know who that was) had a short? That'll give you a punch in the throat The draw is somewhat tight, but I enjoy tight once in a while 
+1 for the DID. It's replacing my v1.1a Orion as my backup Gen. Anyone with the Hellfire Mega (emonty/jolly) using the u-ey wick? Wondering if that makes any difference in flavor? Been trying to get a Mega, throwing out pretty much everything but my Orions to get one, but no luck. Got a mini on the way, so good to hear that its a great vape.
I ran a u-wick for a while. It works, though it was a little bit of a pain to setup. The only thing wrong with the mini - 1ml tank.
Wasn't the reason they went to a u'ey was the dreaded top hot spot and better wicking?
Running my mega single coil. It took about 10 minutes to sort it the first time but I'm Orion trained.
wicking like a fiend, so I dont need a u. That top screw is a PITA. Ive now 5 different ga wire now to find my perfect coil.
JR, maybe a mini mega?
Running my mega single coil. It took about 10 minutes to sort it the first time but I'm Orion trained.
wicking like a fiend, so I dont need a u. That top screw is a PITA. Ive now 5 different ga wire now to find my perfect coil.JR, maybe a mini mega?
Last edited:
I've looked high and low and came up short. Can someone point me to the person selling glass tanks for my v2.1?
Thanks
Thanks
I've looked high and low and came up short. Can someone point me to the person selling glass tanks for my v2.1?
Thanks
Terry from UK Vapers is the person you're looking for. The old site was dot com, the new one dot org.
Wasn't the reason they went to a u'ey was the dreaded top hot spot and better wicking?
Running my mega single coil. It took about 10 minutes to sort it the first time but I'm Orion trained.
JR, maybe a mini mega?
If you want to part with the mega, I have a mechanical Orion 1.1a up in the classies, and I know how much you like your v1s! LOL!
Not tried a u wick on my mega as it is a pain to set it up like that.
Hi everyone i hope i don’t sound to stupid but ive looked other places and cannot find the answer.. To take the tank window off the Orion 2.1 does it just pull of? Or does the top deck have to be screwed of or something before taking the window of? Because i don’t want to break mine and ive got the window to spin on the O-rings, but I’ve only been able to pull it up like 2mm? Thanks for any help!
To take your tank of: pull and rotate slowly at the same time...it will come off. When you put it back on put a few drops of eliquid on them and rub it in as that way it will slide back on easier and next time you take it off again it will be less difficult
The deck cannot be screwed off as it is one piece with the battery top tube
Update on running 1 ohm 30 AWG....all good only gripe the battery life as expected, under load the Panasonic IMR's perform good but not for long...time to order some MNKE batties....
If it was a 1.0, completly stock, not touched by a drill, I might be tempted.
Sorry, not a 1.0, but a 1.1a with the "improved" mechanical switch, completely stock, no drilling, but it was the first ones that had the spring/washer, ground on the body setup.
Update on my 30 AWG coil setup: It is great, can't say more then that, just Great!!!!
- Status
Similar threads
