vasilis will name them as they had to be named risto. Just give him a little time because he has to ship more than 450 orders today and tomorrow
Penelope V3
- Thread starter imeothanasis
- Start date
- th_trl_thread_readers 0
- Status
Including mine! Time to get more bubble wrap from the bubble wrap tree!
Sent from my iPhone using Tapatalk
So, I bit the bullet and ordered from the other side of the world from me...well...more or less.
He's confirmed that the payment was accepted and will be shipping soon. Going to cross my fingers for a safe and speedy delivery. (Because I'm dying of anticipation over here)
I got a Penelope V1 on the first pre-order from CoV, and it's been my main atty since then...rarely put the thing down. Hopefully the V3 will impress me even more.
He's confirmed that the payment was accepted and will be shipping soon. Going to cross my fingers for a safe and speedy delivery. (Because I'm dying of anticipation over here)
I got a Penelope V1 on the first pre-order from CoV, and it's been my main atty since then...rarely put the thing down. Hopefully the V3 will impress me even more.
For me, ESG was actually faster than lots of US vendors. Even for Los Angeles. And they are really prompt with responses to questions both on the forum and via email. As for shipment cost, if you buy more than a few items, it will become cheaper. Lastly, I just like the assurance of buying from the source when it comes to exclusive stuff like GG.
Imeo, now I understand.
I have been misinformed quantity of parts for Penelope v2 and Penelope v3 that were available in the shop.
Because, for example:
Penelope v2 Cap was 3 pieces and Penelope v3 Cap was 34 pieces.
So I thought that these parts are not the same.
Here it is guys. Assembled from individual parts. Great work imeo, but with my fat fingers I hope i don't break anything, I just hope i never disassemble it again lol. You guys just imagine all the parts of the upgrade and the size of penelope base. Really good job imeo.
It's good I dont have wire and wick at work LOL
It's good I dont have wire and wick at work LOL
One thing to note, Imeo reversed the slots (an idea I had but of course he thought of it before me telling him ). So now the air slots are opposite to the 2 air holes. Which makes air completely closed on a device having 510 like JGG. 
). So now the air slots are opposite to the 2 air holes. Which makes air completely closed on a device having 510 like JGG. I just followed your advice aal. I did what you suggested (even if I had a different opinion) and I had a little better result. But the main reason that air is sealed totally now is because slots under the base are not close to the 2 510 holes
Yes they are farther from the connector and opposite in direction. For me now it is the perfect and most advanced atomizer with these updates. I still have to coil it tonight and fire it with full power.
be sure that I hear all the suggestions even if I have a different opinion sometimes aal. I almost always try what you suggest (if I see that you may have a right). And you were enough right on this
Thanks a lot for the suggestion and because you are totally satisfied now
Thanks a lot for the suggestion and because you are totally satisfied now
Last edited:
28 gauge kanthal A1 tension wrapped around 1.58mm (1/16) drill bit. 9 wraps 1.1 ohms.
Test run
Installing the wick
Cutting the wick to size a little off the edges
Pushing wicks to form a blocking effect against floods while keeping channels empty
This is how I do it and this is how it works every time. Blocking the flood of liquid is important when ur coil is small in diameter or else no need.
Test run
Installing the wick
Cutting the wick to size a little off the edges
Pushing wicks to form a blocking effect against floods while keeping channels empty
This is how I do it and this is how it works every time
. Blocking the flood of liquid is important when ur coil is small in diameter or else no need.
Thanks, aalwani. Good to see much of the process in pictures. Very informative. 
- Status
