Proteus official

[67style]

Ah ok i think i got it: VIR can handle 2-35 Watts with 2x3.7v for example on esterigon
Proteus can handle with VIR max 2-25 because of the thin design. Am I right??

 

[imeothanasis]

yes, you are right 67.

 

[Rina]

Hello. Is this the right battery for Proteus? Thank you.

View attachment 388482

AW 14500 3.7 v 700mah Protected batteries.

Specifications:

Nominal Voltage : 3.7V
Capacity : 750mAH ( min. 700mAH ) - tested at 0.2C discharge with end voltage 3.0V
Internal Impedance : < 100 m Ohm ( 1KHz )
Max. Discharge Rate : 2C
Dimensions :14 X 51mm ( +/- 0.5mm )
Weight : 25 ( +/- 2 ) g

 

[imeothanasis]

They are protected Rina, so they work on VIR but up to 11-12 watts. For more watts you must use these:

Batteries-Chargers :: Batteries for Mods :: AW IMR 14500 600mAh - Esmokeguru

 

[JMBH]

They are protected Rina, so they work on VIR but up to 11-12 watts. For more watts you must use these:

Batteries-Chargers :: Batteries for Mods :: AW IMR 14500 600mAh - Esmokeguru

Have five of this AW batteries already ,ready for proteus Can't wait ......
Since you are testing already , how long last single AW 14500 batt. with your vaping style ?

 

[imeothanasis]

I would say very little JM but after the "battery auto balance" system that I put on VIR, it vapes until battery reaches 3,3 volts, that is a long time

 

[JMBH]

Ok Imeo thanks again . I believe it will be conveniently enough then . 3,3 volts limit is far lower then normally change rate in mec. mod 3,6 volts I'm used to . So If I normally use 3 18350 ( AW IMR 3,7v ) for a day vape with esterigon mec. mod. I guess that i would be using more or less the same amount of the AW IMR 14500 with VIR right?

 

[imeothanasis]

As I see it, yes JM

 

[JMBH]

Thanks Imeo ....

 

[soulseek]

Going down to 3.3 Volts is a big advantage. Look at energy difference when going down to 3.3V instead of 3.6V. (note that the 18350 graph goes up to 5A but 14500 only 3A)

 

[imeothanasis]

very nice diagram Seek. It shows that vaping time from 3,6 to 3,3 is long enough

 

[JMBH]

Yes ... Soulseek . Thanks ...

 

[AnilomNor]

Hi Imeo,
Quick question - I have not been following the forum as much (been busy with my one year old). Does this Proteus only use titanium wire? Also, when do you think it might be coming out?
Thanks!
~Nor

 

[Ariel_MX]

Hi Imeo,
Quick question - I have not been following the forum as much (been busy with my one year old). Does this Proteus only use titanium wire? Also, when do you think it might be coming out?
Thanks!
~Nor

Titanium grade 1 wire, stainless steel wire, and titanium e-smokeguru special alloy wire (to confirm).

Before Christmas

 

[67style]

I hope that smokeguru will sell titanium grade 1 too.. i don't know any german shop where to buy.

 

[JMBH]

I hope Imeo will make posible to use ESG Ti alloy with VIR ....

 

[imeothanasis]

I hope that smokeguru will sell titanium grade 1 too.. i don't know any german shop where to buy.

He will 67. I will give him all my stuff

 

[imeothanasis]

I hope Imeo will make posible to use ESG Ti alloy with VIR ....

I hope too JM. i am still trying to find out the way

 

[JMBH]

I hope too JM. i am still trying to find out the way

Its a matter of software setting , right? I understood that you have little memory space , so why not some chips with ESG Ti alloy and SS wires , and others with Ti grade 1 and SS ? A sort of preorder choice ? Just an Idea thought .. Like a VIR ESG edition ?

 

[imeothanasis]

Nice idea buddy. But I dont think that anyone will buy the esg edition. Most people want wires that are available everywhere