So I've been using a igo l and igo w on my itaste mvp . Im using 30g and my builds come out to 1.6 and im running it at 10 watts. My question is what would be the best build for a apv like an mvp or vamo and what watts should it be at ? Obviously I'm still new to this stuff, thanks =)
rda on apv
- Thread starter partywootdgr
- Start date
- th_trl_thread_readers 0
- Status
No answers in over 3 hours and 67 views? The world is awash in common sense!
The reason is, there is no "best" - there is only safe, logical, practical... and what works for you.
As you are well within range for the first three (not pushing on the amp limiter of the MVP certainly qualifies as safe, logical, practical... don't you think? ;-))... the last is entirely subjective.
The reason is, there is no "best" - there is only safe, logical, practical... and what works for you.
As you are well within range for the first three (not pushing on the amp limiter of the MVP certainly qualifies as safe, logical, practical... don't you think? ;-))... the last is entirely subjective.
I was wondering if anyone would respond lol and what is the amp limit on a mvp ? And im not sure how that works anyways , where can I find info on that ? Obviously I want to be safe lol
Haven't put a dripper on my MVP but I do run a 1.4ohm microcoil on my RSST with it. Hits wonderfully at 11 watts.
3 amps on an MVP... 5 on an SVD. This information can be found in Innokin literature, if one is willing to look for it. ;-)
Although this won't explain why different APVs have differing amp limits (mostly due manufacturer research of the market demographic wants/needs for a particular device... research the Chinese quite often miss the mark on), it will offer useful links, each explaining elements to the basics of a lot of things, like resistance to amperage values.
k i looked it up , one other question i had is say im vaping on my vamo with 1.6 at 12 watts im still in the amp limit but is it dangerous to use that battery down past 3.7v? i know the mod doesnt let you fire it past 3.2 or 3.3 but is that safe discharging the batter past 3.7 or 3.6v?
The 3.2 volt cutoff is supposed to be within the safe low voltage zone but there is a school of thought that it's better recharge when your battery is down to 3.4 or 3.5 volts.
I typically change batteries when I get home from work and they are usually around the 3.5 volt mark but I don't worry about it on the weekends and then I'll change them when the mod cuts out at the 3.2 volt mark.
I typically change batteries when I get home from work and they are usually around the 3.5 volt mark but I don't worry about it on the weekends and then I'll change them when the mod cuts out at the 3.2 volt mark.
So many combinations and permutations: ejuice, battery device, RDA, wire type size, wicking material. Which adds to the enjoyment of experimentation. Easy to start at lower wattage setting and work higher until - OH! That's It!
One of my favorites, most everyone's is different, for MVP 2 (or SVD or 134), IGO-L and my juice: 1.5 ohm micro coil, 11 wraps, kanthal 28 gauge, peaches and cream cotton yarn (walmart) at 8 watts.
Same build and wattage when I use my kayfun 3.1 or kayfun lite: wicking material change to cotton yarn inside of ekowool. Just seems to work better for me with RTAs. Plan to try readyXwick (RBAsupplies) when it arrives.
One of my favorites, most everyone's is different, for MVP 2 (or SVD or 134), IGO-L and my juice: 1.5 ohm micro coil, 11 wraps, kanthal 28 gauge, peaches and cream cotton yarn (walmart) at 8 watts.
Same build and wattage when I use my kayfun 3.1 or kayfun lite: wicking material change to cotton yarn inside of ekowool. Just seems to work better for me with RTAs. Plan to try readyXwick (RBAsupplies) when it arrives.
it is my understanding that the vamo cannot fire a coil below 1.2ohm. now i have been rebuilding PT3's with 3.0-3.3ohm single coils with cotton wicks and running them at 10-11 watts, because my juice burns over 11watts. and i run my batteries until vamo cuts off the power.
- Status
Similar threads
- Locked
