I can't even find the origen v2. Wanted to get one with bottom feed. Thing is like impossinle to fi d.
Sent from my SGH-T999 using Tapatalk
Sent from my SGH-T999 using Tapatalk
Reo compatible RBAs
- Thread starter hildicat
- Start date
- th_trl_thread_readers 0
-
- Tags
- evic fasttech mt baker myvaporstore
- Status
I would suggest you try going to Vaping Craze website and click on bottom contact us and shoot them an email if and when they will have Origen v2 and the bottom feed kit. Then do the email me when back in stock for the items you want. Each time I emailed them I got a response. GL
Last edited:
These are supposed to be available on 05/17/2014 for 90 Euros=$125 from tuttaltroshop.it
Bottom feeder kit for V2 is available at Vapincraze. I received a notification today.
HOW DOES IT WORK WITH THE MICRO and i assume cotton wick???
oops i thought i copied the pics of your No Name atty...
The posts look a bit like the Micro Gen, by Jasl90 ... which he uses an 801 atomizer bottom and makes the tiniest rba from at home. You can possibly fit some eko wool over the post post instead of mesh too; makes it a lot easier to eliminate hot spots.
I think i'd like to give that one a shot; viva Italia!
oops i thought i copied the pics of your No Name atty...
The posts look a bit like the Micro Gen, by Jasl90 ... which he uses an 801 atomizer bottom and makes the tiniest rba from at home. You can possibly fit some eko wool over the post post instead of mesh too; makes it a lot easier to eliminate hot spots.
I think i'd like to give that one a shot; viva Italia!
Last edited:
Oh since i last posted about my Origen V2 b/f... Its grown on me big time!
I wrapped mine horizontal duals micro... 26g nichrome = .40 ohms, cotton wick, after acouple days it gets up to .5+ ohms, not harsh at all, just lots and lots of surprisingly tasty vapor, and on frequent short squonks just to refresh the top side of the wicks, even better flavor.
(the coils last months; just rewick every week - dry burn coils first)
Of course the deep well allows you to vape a long time between squonks to fill the well too.
Only downside, I keep a couple AW IMR 1600's in the car/truck for backup... I go through one in an hour of chain vaping.
The Reo Grand LP w/Origen v2 is a WINNER!
Its brought b/f'ing to a whole new level imo (after thinking drip tanks and tubes were the ultimate for a long time now)
I wrapped mine horizontal duals micro... 26g nichrome = .40 ohms, cotton wick, after acouple days it gets up to .5+ ohms, not harsh at all, just lots and lots of surprisingly tasty vapor, and on frequent short squonks just to refresh the top side of the wicks, even better flavor.
(the coils last months; just rewick every week - dry burn coils first)
Of course the deep well allows you to vape a long time between squonks to fill the well too.
Only downside, I keep a couple AW IMR 1600's in the car/truck for backup... I go through one in an hour of chain vaping.
The Reo Grand LP w/Origen v2 is a WINNER!
Its brought b/f'ing to a whole new level imo (after thinking drip tanks and tubes were the ultimate for a long time now)
If you go low low ohms, I give it a day to settle in resistance AND the flavor improves once the coil/wick seasons too... at first it seemed overwhelming but you can always count on it to perform.
Got my Cyclone bottom feeder today.
Gave it a good clean, drilled the tiny airhole out to 1.8mm and rolled a 7 wrap 26g micro @ 0.5ohms with cotton.
The threads were a bit tite so wound it in and out a little bit at a time until it fired.
I don't think it is the version with the low drain hole but still drains well.
First impressions are that it is a well machined little atti and vapes nice, very similar to the RM2.
Gave it a good clean, drilled the tiny airhole out to 1.8mm and rolled a 7 wrap 26g micro @ 0.5ohms with cotton.
The threads were a bit tite so wound it in and out a little bit at a time until it fired.
I don't think it is the version with the low drain hole but still drains well.
First impressions are that it is a well machined little atti and vapes nice, very similar to the RM2.
Got my Cyclone bottom feeder today.
Gave it a good clean, drilled the tiny airhole out to 1.8mm and rolled a 7 wrap 26g micro @ 0.5ohms with cotton.
The threads were a bit tite so wound it in and out a little bit at a time until it fired.
I don't think it is the version with the low drain hole but still drains well.
First impressions are that it is a well machined little atti and vapes nice, very similar to the RM2.
Flavour is very nice.
How much was the combo, the cyclone itself + the bottom feed kit?
Sent from my Nexus 7 using Xparent Purple Tapatalk 2
Sent from my Nexus 7 using Xparent Purple Tapatalk 2
Shhesh, my mistake, thanks for the answer. With the discussion about the conversion for the origin going on my mind immediately plugged in conversion and applied it to the cyclone.
Sent from my Nexus 7 using Xparent Purple Tapatalk 2
My first bf modding - actually my first modding of any kind. The Igo-F - fits perfectly on the standard Reo and works very well.
24 hours with the cyclone and still enjoying it.
NO leaks so far, which surprised me from an O ring cap.
Vapor & flavour are excellent.
Also liking the look where it sits down inside the drip cup.
Fantastic Paul!
I have put mine through the test the last couple weeks with no issues at all. Seems the o-rings have a spectacular tolerance for fit. Thinking about it, most atomizers with small combustion chambers seem to have the best flavor.
I expected to have to modify my feeder hole a bit lower but, as I mentioned on another thread am glad I vaped it as is. I suspect the change on the Cyclone came when someone @ Vicious Ant thought a higher hole may soak the wick more efficiently? without affecting the drainage
I am quite impressed with the construction and performance. Looking for #2 here shortly.
I hope you get much enjoyment!
Last edited:
- Status
Similar threads
