Scubagen Mods

[caillel]

I think it is smaller than that.
I found this:

Inch Equivalent Metric Size-Pitch
ISO and IFI Rec.
UNC UNF
1 - 64 1 - 72 M2 x 0.4

 

[caillel]

There may be no equivalent

 

[mj64]

I think it is smaller than that.
I found this:

Inch Equivalent Metric Size-Pitch
ISO and IFI Rec.
UNC UNF
1 - 64 1 - 72 M2 x 0.4

Yes, you're right, I hadn't looked at it in detail yet. This is a very useful chart. Conversion Chart - inches to mm

 

[caillel]

The nut was an #0-80 It is stated to be 3/32" across the flats, and .048 " thick.
The washers were stated to be ID is .05" and the OD is .195", 1mm thick.(.0394")
So the #0-80 nut is .09375" across the flats, a bit smaller than the original washer, but then it has flats.
The real question is will a #0-80 nut slide nicely on a 1/2" 19 guage wire nail. I can't find the ID, but I will keep looking.

Also, I found wire nails, but they only had steel in that size, not stainless. I wonder if that will rust.

 

[Teach]

Since these aren't made to exacting specs there can be some variance, but...

The m1.6 pan head screw od mics at 1.54mm - 0.0605" - 1/16th".
The 19x1/2" wire nails od 1.02mm - .042" - 5/128th"

hope that helps

 

[mj64]

I found the nuts at my Ace Hardware. Here's a pic of the drawer for you guys who may be having a hard time closing in on them. It's the second drawer from the top!

 

[Scubabatdan]

Just in case you guys did not see...
Here are the winners of the two SCUBAGENv3's that were raffled at VapeStock in FL:
Congrats to LambChop and Classwife!

Dan

 

[Turbo]

It was fixed (notice the ladies)....lol....just kidding of course, congrats!

 

[NotoriousJoe]

Can I get the measurements for the polycarb parts? Gonna go ahead and cut a few.

 

[UA72Riddle]

Check the very first post. I put a few useful links in there so we would have them. Length of mesh and tubes are one of them.

But since I have already cut quite a few, bottom is 1 5/8, top is 7/8.

Can I get the measurements for the polycarb parts? Gonna go ahead and cut a few.

 

[Scubabatdan]

Can I get the measurements for the polycarb parts? Gonna go ahead and cut a few.

Actually, the measurments for the ones ordered is Bottom: 1.75", Top 7/8".
Sorry that was the one I originally created. The ones that were ordered I increased slightly to add more room for juice. And make it s a standard size.
I appologise I did not ammend that.
Dan

 

[MagnusEunson]

Notice Dan did not acknowledge that the Scubagen drawing was fixed for the pretty smiling ladies. Tsk tsk. ;-)

Thanks for all your hard work Dan on the co-op, design, and support! -Magnus

 

[Teach]

Can I get the measurements for the polycarb parts? Gonna go ahead and cut a few.

here are all jic:

• the four holes on top are 1/8" two are shallow for the electrical connector and two go all the way through for the SS wick. And there is one more that is 1/16", this is the fill port
• Wick size is 4" x 1.5" This will roll down to appox 1/16" And reach from one side bottom to the other.
• Poly tubing size 7/8"OD x 3/4"ID x Approx (Bottom) 1 3/4" Long, (Top) 7/8" Long
• O-Ring Size is 3/4"OD x 5/8"ID x 1/16" thickness
• 1/2" x 19ga Wire nails, the springs fit on them perfectly.
• Still up to you to make the beveled washers out of 4 old attys, or carto center post.

And congrats classwife and lambchop... you lucky girls you!

Thanks for the update Dan! Good thing you beat me to it.

 

[Scubabatdan]

Notice Dan did not acknowledge that the Scubagen drawing was fixed for the pretty smiling ladies. Tsk tsk. ;-)

Thanks for all your hard work Dan on the co-op, design, and support! -Magnus

Just cause it was the two women "at my table" who won, does not mean it was fixed LOL
I was no where near the drawing bucket, nor was I in control of the person drawing.
But it was funny the two people at the table I was sitting at won them!

hehehehe... yes i know what you are thinking... "he still did not say it wasnt fixed"
Dan

 

[Scubabatdan]

here are all jic:

• the four holes on top are 1/8" two are shallow for the electrical connector and two go all the way through for the SS wick. And there is one more that is 1/16", this is the fill port
• Wick size is 4" x 1.5" This will roll down to appox 1/16" And reach from one side bottom to the other.
• Poly tubing size 7/8"OD x 3/4"ID x Approx (Bottom) 1 3/4" Long, (Top) 7/8" Long
• O-Ring Size is 3/4"OD x 5/8"ID x 1/16" thickness
• 1/2" x 19ga Wire nails, the springs fit on them perfectly.
• Still up to you to make the beveled washers out of 4 old attys, or carto center post.

And congrats classwife and lambchop... you lucky girls you!

Correction in red
Dan

 

[Teach]

Correction in red
Dan

I hesitate to ever change a number you put out... even the format. Hope you had a great time (wink, wink, nod, nod) at VapeFest... doubt your reputation will ever recover (in that aspect anyway).

 

[Scubabatdan]

I hesitate to ever change a number you put out... even the format. Hope you had a great time (wink, wink, nod, nod) at VapeFest... doubt your reputation will ever recover (in that aspect anyway).

Wait what did you hear or see at vapestock LOL
I had a great time, loved meeting everyone!
Dan

 

[nicotime]

When I went to ace, they had some really small ones, but they listed in standard sizes.
Is there a standard equivalent to M1.6?

Too big....you need some 0000-160 UNM screws...may have to co-op them though!!LOL
Numbered Miniature screws, Miniature Screws & Fasteners - JI Morris Miniature Screws & Fasteners

 

[classwife]

Dan was a perfect gentleman !!


Hi Nico !!!!!!


Visably pulling up a chair......I've been here, but ya never knew it !

Hi All !

 

[PKZap27]

Hi Classy!