Seven 30
- Thread starter 350ZMO
- Start date
- th_trl_thread_readers 0
-
- Tags
- big fogger seven 30 seven-30
- Status
Not a bad idea. However, my end goal has always been to have a high voltage semi mech/SX350 hybrid mod, and I can't do that with the Seven-30 as the body. Using a 1560g gives me a little extra room to work with, once I figure out how to drop 7.4v to between 3.3v and 4.5v for the chip.
Sent from my hTC One M7
So I've been running 0.75 ohms at 20watts for a few weeks no signs of problems except when the battery dies it says "check atty" instead of check battery and it always did that. I'm tempted to try lower ohms but hate being the guinea pig (can't afford it.)
I put in my AsMODus order last night, should have it by the 25th [emoji111]
I'll let you know how it is. I'm thinking of running it at somewhere around 7.4v with a 0.1ohm 28g 4x triple parallel build, since I'll finally have a big enough dripper to build it. If you never hear back from me about it, just assume I drowned from the amount of vapor I tried to inhale [emoji13]
Sent from my hTC One M7
Just an update on that shorted battery the other day: this is what happens when you're holding a mod with a battery on its way towards thermal runaway.
Sent from my hTC One M7
This atty was clearly made for the Seven-30.
Sent from my HTC One using Tapatalk
This atty was clearly made for the Seven-30.
Sent from my HTC One using Tapatalk
Or, you know, their 26650 30mm Fat Snow Wolf mod...
Still waiting for 101vape to restock on the SS Mutant so I can order both that and one of these attys at the same time...
Nope. Definitely looks better on the Seven 30.Or, you know, their 26650 30mm Fat Snow Wolf mod...
Still waiting for 101vape to restock on the SS Mutant so I can order both that and one of these attys at the same time...
Sent from my HTC One using Tapatalk
But, speaking of this atomizer, it works great for my stacked 26650s. 0.5 ohm 4 strand braided 28g, 7 wraps on a 3/16 drill bit then stretched apart, with the air holes drilled out to 1/8 and the drip tip drilled out to allow full airflow, it's working perfectly. Should be pulling about 140w with fully charged batteries. The one thing I don't like is the post holes are very awkward to insert coils into. However, they're huge. I could probably fit 4 strands of my braided wire through them. With enough power, I could run quad parallel coils with the braided wire, that's 16 28g wires through one post. However, the heat from that many coils would probably melt the atty lol. I'm thinking it's time for me to get a 32v battery, and try this setup x4. There's easily room in the atty, and with the 4mL juice well I wouldn't have to worry about dry hits.
Sent from my HTC One using Tapatalk
Sent from my HTC One using Tapatalk
Last edited:
Does anyone know the size of the 510 screw on Seven-22 and Seven-30? Nothing will fire on my Seven-22 because the 510 screw sits too deep in the connection. I check Lowe's and couldn't seem to find anything remotely close to it.
I can back it all the way out, as far as it will go before it completely comes out, and still the only atty I can use is a fogger which has adjustable 510. I contacted P4U and the vendor I bought it from and never heard a thing back.
I'll get home in a couple of days, will measure it and will get back to you on that.
Check out my Seven-30 box mod! (see what I did there?)
Sent from my HTC One using Tapatalk
Sent from my HTC One using Tapatalk
The screw:
1. Thread------------M3.0 pitch 0.45mm
2. Total Length-----6.0mm
3. Head Length----1.0mm
4. Head Diameter-4.2mm
My last (I promise) revision of Wolverine 19 ML
1. All around Airflow holes are now 3.0mm (0.118")
2. New, SS Center Pin now has dual wire posts
At 0.347 Ohms and wide open Airflow - It, pretty much, became a Dripper. Direct lung inhale - No Problems.
1. All around Airflow holes are now 3.0mm (0.118")
2. New, SS Center Pin now has dual wire posts
At 0.347 Ohms and wide open Airflow - It, pretty much, became a Dripper. Direct lung inhale - No Problems.
30mm Magma anyone? I haven't tried her on my Seven 30 yet....but I bet it would work fine at .7-.8!
Question: Ive had my Seven 30 for about 10 days so I dont have anything to gauge this on, so for those of you with the Seven 30, on average how long will your battery last before you have to recharge it running at about 15-20w with a .08 to 1.0 coil? I seem to be draining batteries in less than 2 hrs! Both batteries are new, one efest one MNKE, 3500 mah and using an intellicharger... im thinking I may have a problem with the mod...
With a 0.8 ohm build at 20 watts, you're running about 5 amps. On a 3500 maH battery, you should be getting about 30 minutes of solid vape time. In other words, if you're vaping a total of 15 minutes an hour for 2 hours, your battery life is accurate. Also, once it gets down to a certain point, it automatically stops firing, which accounts for the less than 2 hours you're getting, because technically you can't run the battery all the way down. As well, the capacity of our batteries is usually exaggerated a little bit by the manufacturer or retailers.
Last edited:
Wow! Thanks for the quick reply.. I feel much better now. Im used to using 1.8-2.0 coils on an itaste 134 mini or my SVD which goes several hours. I guess I better invest in a few more batteries! My nitecore i2 takes 5-6 hrs to charge 26650's one at a time. Is this the best way to go or do yiu have a better recommendation?
- Status
