Thanks Bozz, My original supplier quit selling them for no known reason. I just filled my 5th resurrector and burnt. I guess I got lucky 4 out of 5. And a correction to my post as the wrappers are clear.
Mine does that sometimes, and I unscrew it and screw it back in and it works fine, who knows why but it happens. I have put a small drop of E-juice on the edge of the button and press it up and down a few times then wipe off any excess, and that seemed to help with the sticky button. I unscrew the carto each time I change a battery and clean the center of the battery switch and the bottom of the carto with a tissue or napkin, it is not unusual to see some fluid in it, so thats why I check it. Once I thought my switch was dead and I cleaned the treads and post with alcohol and Q-tip and it worked fine after the cleaning.
I have not had any more problems with the ressurectors than any other carto and when I do its usually either the center post of the battery or the center connector in a carto being to low, in the carto the center connector should be lhigher than the threads by just a little. You can raise both areas with tweezers and just pry up each side just a little. One time I thought my switch had died and cleaned the battery connector with a q-tip and alky and wiped the rest of the threads with a napkin and alky then its worked great after that. Don't give up if the ressurector works on one battery it should work on another. The flashing light sounds like a bad connection (needs cleaning) or the carto is shorted. If you have a volt/ OHM meter check it out and if the meter shows its OK then it will be one of the things I mentioned above. What mod are you having a problem with??i had all the same problems, lol. its weird now some og the ressurectors wont work with it. they just flash like the battery is dead. fresh of charger bs. so i put some 2 ohm ones that i got with it not my 1.7 and works fine. I have a feeling that the ressurector problems are caused by the company putting the wrong coils in.
Try pushing a straightened paper clip up thru the battery end and and all the way thru the center straw of the carto, do this by turning the carto as you press the paper clip gently in to it, then spin it around a few times and remove it and vape. I do this when the vape gets hard to draw. Also sometimes they get flooded and you can blow it out from the mouth piece end with a napkin under the threaded end. A carto works the best when you can see light thru the carto if held up to a light source.I got a set from my vendor that came in clear wrapping. I love them for the first 3 days of vaping, then they start to draw hard. Any thoughts or solutions?
That's what I use all the time and have not had a bad one yet, maybe just luck. I sure hope I don't have any problems when I order again. I have use about 15 of the S.S. and not one dud. Then have been all in clear wrappers.Also wondering if anyone has tried the Stainless Steel versions of the resurrectors and if they have the same problems.
That's what I use all the time and have not had a bad one yet, maybe just luck. I sure hope I don't have any problems when I order again. I have use about 15 of the S.S. and not one dud. Then have been all in clear wrappers.
I just ordered one of the smoktech 3.5mil tanks with the smoktech 1.5 flange carto's. I didn't order it from madvape's but a lot of people in comments section are complaining about the same issues discussed in this thread. However, a few have said the carto that came with the tank worked great, it was the replacement carto's they were having an issue with.
cheers,
Also wondering if anyone has tried the Stainless Steel versions of the resurrectors and if they have the same problems.
To clear up confusion about green vs clear. I was told this by a vendor.
Smoktech DO NOT manufacture their cartos! They outsource the manufacturing.
The green wrapped and clear wrapped are from different manufacturers/factories contracted by Smoktech to produce these cartos to their spec.
This is the reason for the differences.
Hope this helps.
Andrew took on some part time help who accidentally deleted some info (this is aside from the syringe notice). If you can email him (link on the site) and give him an order number and info like that, he is straightening it out. Give it a day or two after emailing, this was a major tangle and he is moving as fast as he can to fix it. He contacted me in 2 days and my order is going out in the morning. Mine was a deleted order. You can also go to the CCV thread here on ecf for more info and another contact person.anybody knows whats up with CCV, I ordered some 510 1.7 cartos( 15 deal...) and its been 4 days now and no shipping info. They posted a notice on web site s aying they have some legal issues and will be happy to offer refund etc etc.
whats up with that