- Status
That just might be the ticket as a tank style is my preference, now if I can locate one here. I think I have seen it from US vendor
I found this at GotVapes in their Alpha section, is the Avalon anything like this?View attachment 125536
If any of them had the dread word P*****i in them then you did everyone on this board a favor?
Errol
Last edited:
Yeah kinda, except the Avalon got a tank..
The one in the pic looks more like my bully from Peleon. (a rebuildable atomizer without a tank. Its made for dripping)
optimo, are you still in for co op for vmax? if so better pm shek with your email addy by friday or hes deleting you. Just giving u heads up
DW...you don't want that type....I'll give you a link for the Phoenix "type" atty.
Link: PHOENIX Rebuildable Atomizer
Thats the 1 I have and it's awesome.
I may take another try at mesh wicks, does VG do a better job (than PG) of putting the final "finish" on it ?
Disrespectfully disagree.
I agree with you I had a new ss vmax burn out in 2 weeks vaping it at around 4.3 with 1.9 on the did atty! Its crap:thumbdown::
I"m I the only one confused, by the way F1 and F2 functions work.
Then you disagree with me, splither.
Hope you bought it from a reputable vendor man. Good luck!
I say and use pg as my last 2 processes. PG holds and transfers flavor much better than vg, that's why most flavorings are pg based. All I really do now is torch the mesh real good before rolling it.....then roll it up......2 torch and quenches in pg,letting burn off slowly......then 1 or 2 slow burns with the juice I plan to fill the tank with.........after good and dry but cooled 3 wraps of rollin' paper (any papers will do)......wrap a 3/4 or 4/5 coil with 28, 30, 32, 33, or 34awg kanthal (depending which atty, how much room I have to work with on the mesh between terminals to get the resistance I want, and what device I plan to use it on [usually mechanical due to that's what RBA's were originally designed to be used with from the start] ). This rather quick process has served pretty well with little to know shorts or hotspots and impeccable flavor re-production.
not sure if this was discussed yet(read back only 6 pages) but what is different in SS VMax Revision4 (Rev4) from prior revisions? What is the latest revision/version of VMax out there - anyone knows?
I will order Phoenix RB probably in the wee hours of this coming morning. What I have in mind for a wick is ss under coil with cotton running through it. I think my shorting problems with ss on ViVi RB was when I would tighten screw on post it tended to want to pull wire to tight on mesh. I am going to use coffee filter paper next as I had funny feeling pulling cigarette out of my wife's pack to get the paper. Thanks
Any suggestions for voltage on 1.5 ohm dual coil cartos and 2.8 ohm fusion cartos? Seeing how I've never dealt with the "single " button like the ss vmax or that other more expensive mod would rather try what has/does work for someone else and go from there thx
would rather try what has/does work for someone else and go from there thxHey Dw,I have the phoenix rba and am currently using 100% egyptian cotton thread i got from hobby lobby and 1.5 ohm 32g kanthal.It is literally the best vape I've had since i started Jan. 2011.I like the idea of cotton inside ss mesh,but you have to keep cotton wet at ALL TIMES.On the +side it holds a lot of nicuid.Oh,yeah,got mine from VB(vapor.....)
Any suggestions for voltage on 1.5 ohm dual coil cartos and 2.8 ohm fusion cartos? Seeing how I've never dealt with the "single " button like the ss vmax or that other more expensive mod
I run my 1.5DC (when I use them on the Vmax) around 3.5-3.7 depending on the juice. My 2.8's I really like at 4.2 no matter what the device or juice.
Salky
Any suggestions for voltage on 1.5 ohm dual coil cartos and 2.8 ohm fusion cartos? Seeing how I've never dealt with the "single " button like the ss vmax or that other more expensive mod
Hey Lava....On my Fusions I usually stay at 3-3.5 volts, just start off at 3v and after 2-3 draws go up in .1v increments till you get that sweet spot you prefer. On dual coils I find that the 2.0, 2.5, and 3.0Ω ohm Dual Coils perform much better than the 1.5Ω DC's on the VMAX. I use the 2Ω DC's mostly at 4-4.4v, I think Fuzzi runs the 2.5Ω at 4.5v, and the 3.0Ω I run at 4.5-4.8v. Hope this helps.
** This is the main reason Fuzzi started this thread** Perfect example of a ideal post Q & A.....I think ...lol
- Status
Similar threads
