Some homemade attys and genesis

[ooSTURMoo]

I think on ebay you should buy this LED

You need to look


EDIT:

There is a change to the resistance.

0.20 x3 wraps - with a new configuration (before use) multimeter showed 1.3 ohms. After a few hours of use 1.8 ohm.

Now I have a 0.20 x 4 wraps - before 1.9. Now, 2.1 ohm

The resistance to change how we use longer

 

[jbs]

@ooSTURMoo

Great job. But i would refer to it as Ego-T Genisis. Hmmm.... actually it should be rather easy to make one of these out of Ego battery tube, Ego-T cartridge and a little bit of Stewalin/Artstone.

 

[Gummy Bear]

more oxidation.

 

[ooSTURMoo]

German, solid version

 

[ooSTURMoo]

With EGO tank cartridge

 

[jbs]

Indeed, my bad. But simplicity of your mod reminds me more of ego-t. German version is for those lucky lathe owners.

 

[ooSTURMoo]

My next project is the Genisis VORTEX

Soon....

 

[WillyB]

I believe that the tank over the, "Genisis" is a very good direction for future mods. We do not need to use tricks when vaping. Liquid flows easily to the heater. Wick is not dry - never. If we make a hole in the tank to the width of the wick will not leak.

Well our old, and gone it seems, thread starter, JensB switched to and preferred that design.

Ichbine's LV2.

Thanks for the heads up on those flashlights, too cool.

 

[lorderos33]

Hot dang looks like we got us a contest going here between scuba and sturm!!!

Hahahahahaha, just kidding guys, lots of great ideas swimming around in here over the last few days. Keep it up guys

 

[Scubabatdan]

German, solid version

Uh-Oh wheels are turning, this would be VERY easy to make in a poly tube version with aluminum caps.... might take a stab at this one with a 6ml plastic bottle, and some 7/8" poly tubing
Cool...
Dan

 

[ooSTURMoo]

Hot dang looks like we got us a contest going here between scuba and sturm!!!

Hahahahahaha, just kidding guys, lots of great ideas swimming around in here over the last few days. Keep it up guys

There is no contest.

I am passionate, and I have pleasure share my ideas.

I started my adventure with the e-cigarettes in this thread, and here I am trying to continue

 

[lorderos33]

Uh-Oh wheels are turning, this would be VERY easy to make in a poly tube version with aluminum caps.... might take a stab at this one with a 6ml plastic bottle, and some 7/8" poly tubing
Cool...
Dan

HAHAHAHAHAHAHAHA, too funny, I was thinking almost the same thing but I was thinking a 10ml bottle

 

[lorderos33]

There is no contest.

I am passionate, and I have pleasure share my ideas.

I started my adventure with the e-cigarettes in this thread, and here I am trying to continue

That's cool I was just being a clown for a minute, lol

 

[l3oertjie]

that's cool i was just being a clown for a minute, lol

lorderos being a clown

 

[Scubabatdan]

Ok here is what I will be working on this week end
Concept using 7/8"OD x 3/4"ID Poly tubing, and 7/8" Aluminum stock.


The center aluminum piece will be tooled to match the bottles cap, and have 4 air holes drilled around the perimeter of the bottle to allow vapor from the bottom chamber. The bottle will be a tight fit to the center piece so you have to wiggle it down into position and back out helping with the seal. The mouth piece will be slotted for side air access. Think I will try and add my quick clips if I have time. Would like to have it functional this weekend.
Dan

 

[l3oertjie]

Ok here is what I will be working on this week end
Concept using 7/8"OD x 3/4"ID Poly tubing, and 7/8" Aluminum stock.
View attachment 39377

The center aluminum piece will be tooled to match the bottles cap, and have 4 air holes drilled around the perimeter of the bottle to allow vapor from the bottom chamber. The bottle will be a tight fit to the center piece so you have to wiggle it down into position and back out helping with the seal. The mouth piece will be slotted for side air access. Think I will try and add my quick clips if I have time. Would like to have it functional this weekend.
Dan

Nice..... Post quick performance review please....

 

[l3oertjie]

Boys, we are modding, inventing, patenting, open sourcing (bless them souls) and whatever else.... What are we trying to achieve? What would you describe as the ultimate vaping experience? What are we trying to achieve?

 

[lorderos33]

Boys, we are modding, inventing, patenting, open sourcing (bless them souls) and whatever else.... What are we trying to achieve? What would you describe as the ultimate vaping experience? What are we trying to achieve?

What we are trying to achieve is vaping nirvana of course.

We want the highest performing, most convenient and coolest looking PV we can get. Since we can't get there by buying some device that is mass produced in China, we instead turn to the collective knowledge we gain from each other through failures and achievements PLUS it gives us something to do in our spare time, lol.

Think of it like this... You could spend $60,000 on a corvette or you can own a hand built Ferrari. Given the choice, what would you prefer. Most of us end up picking the hand built Ferrari. We don't need it, but we want it ad so the same goes for our mods.

That and world domination!!!!!!!
HAHAHAHAHAHAAHAAAAAA!!!!

 

[lorderos33]

Ok here is what I will be working on this week end
Concept using 7/8"OD x 3/4"ID Poly tubing, and 7/8" Aluminum stock.
View attachment 39377

The center aluminum piece will be tooled to match the bottles cap, and have 4 air holes drilled around the perimeter of the bottle to allow vapor from the bottom chamber. The bottle will be a tight fit to the center piece so you have to wiggle it down into position and back out helping with the seal. The mouth piece will be slotted for side air access. Think I will try and add my quick clips if I have time. Would like to have it functional this weekend.
Dan

Nice!!! That looks like it will be interesting

 

[Gummy Bear]

Naw,, we can give world domination to "Conotocaurious"