There's no specs from Yihi yet for Ti
Although I would say go for 5 wraps of 26awg at 3mm & you cant go wrong especially in a subtank mini
SXmini M Class (TEMP CONTROL)
- Thread starter whitewidows
- Start date
- th_trl_thread_readers 0
- Status
There's no specs from Yihi yet for Ti
Although I would say go for 5 wraps of 26awg at 3mm & you cant go wrong especially in a subtank mini
I guess I'll step back a little bit and plan the next acquisition then. I agree with you that it will be great if youde produce a Ti coil. Until then, I will have to find Ti wire around here (I haven't see any so far)Don't want to put you off as it a nice tank
The factory coils work so well, you can just keep chain vaping and never go dry
Hit them with 40w+ & they certainly produce plenty of vapour
Air flow is wide open & if they bring out pre made Ti coils for this it will likely become my favourite tank as would save me building them
[ tag: Youde Zephyrus Titanium Coils ] hope they see this & start production
Abroad, I am in Indonesia. There are plenty Ni 200 here, but no Ti wire around
I'm not sure about the shipping cost but you can pick up 24ga from Rio Grande and they ship to Indonesia. It's not on their "no ship" list.
It may be with checking. $10 for 50ft.
Titanium Round Wire, 50-ft. Coil, 24-Ga., Soft
It may be with checking. $10 for 50ft.
Titanium Round Wire, 50-ft. Coil, 24-Ga., Soft
Or there's ZiVipf in Germany, and Vape Mesh / Crazy Wire in the UK - both will ship to Indonesia I am pretty sure.
Vape Mesh: http://www.vape-atomizer-mesh.com/products/Titanium-Wire---Titan-Wire.html
Zivipf : Titanium Wire - Zivipf Onlineshop
Vape Mesh: http://www.vape-atomizer-mesh.com/products/Titanium-Wire---Titan-Wire.html
Zivipf : Titanium Wire - Zivipf Onlineshop
QM with the Ti upgrade I take it you still use Joules. Normally on nickel my coils are about .07 and I run them between 390-400 12J. With a Ti coil 26awg 5 wraps what do you run it at as far as J and temp. Is it about the same as nickel or do you have to use more J for the higher resistance from what you have said about .2ohms. I would think the temp should be about the same. Since I like 28awg nickel you think 26awg Ti would work good for me. I don't care for a hot vape which is why I use 28 instead of 26 in the NI200. You think the 26 Ti is a cooler vape then nickel same gauge.
Its a fairly cool vape to me ymmv mate
I set tp to 260f and start at 14J then up it to 17j for the rest of the coils life
Would expect with the thicker wire & not that much more power it should be comparable to your Ni200 build as I was running below 400f too with nickel
I settled for 26awg as that was my favourite size for kanthal, although I did get some 28 & 29 Ti I have not used it yet
You can play about with TP to control the warmth of the vape, I did run at upto 290f but was too hot for me although it still worked well
26awg seems to be a happy medium for ease of coiling
ok I was wondering with the upgrade what it will be I thought you had the beta version
Also what kind of double sided tape did you guys use to keep your sleeves from sliding up. Mine are coming to day we are going on vacation in our motorhome and I want to double bag my 3 SX's
GS Air M nickel build. .064 ohm @375 and it performs flawlessly. I was skeptical that the resistance might be unstable but it has been vaping nice for the last hour. Pretty decent clouds and flavor.
That's the other thing QM I use 28 kanthal. I wonder what the limit will be on resistance for Ti I guess I need to talk to someone who has the beta because 5 wraps of Ti1 would be .35 according to steam engine. I wonder what the upper resistance will be.
lol, no. Not even close. I'm expecting yihi to release a new j chip by the end of summer though.
The GSA M nickel build works equally as well on the VaporShark. I guess you can use nickel in any atty you like. I'm gonna try my old original Evod next.
So far I didn't use any. It did occasionally sliding up a bit but not that much. I have a standard Chinese no name sleeve here.
- Status
