Technically it isn't Yihie...the full company name is Dongguan Yihi Electronic Co., Limited.
The company's emblem uses capitalization like this: YiHiEcigar. The Yihi is separate from the Ecigar.
Last edited:
SXmini mod ... Yihi
- Thread starter bonmatos
- Start date
- th_trl_thread_readers 0
- Status
Technically it isn't Yihie...the full company name is Dongguan Yihi Electronic Co., Limited.
The company's emblem uses capitalization like this: YiHiEcigar. The Yihi is separate from the Ecigar.
M2.5x6. I thought they wouldn't go all the way in at 6mm, but they work a treat!
Yihai
Looks like they can't keep it straight themselves: About-yihiecigar,sx350,Yihi SX350,dna30 30W chip,SX350 35W chip Manufacturers & Suppliers - Dongguan Yihi Electronic Co.,Limited
Go for duals
. Its an awesome vape.Lol! You still don't have a Lemo. $30 authentic and nearly as awesome.
I was looking at them today.
With the Aqua I was reluctant, I've never liked the air holes on the deck without a chimney but you made me a believer with the Aqua!
Duals Peter!
Last edited:
I still can't believe I only have one Lemo
Unfortunately, your Kayfun and Russian will end up in a drawer.
Unfortunately, your Kayfun and Russian will end up in a drawer.
I still can't believe I only have one Lemo
Unfortunately, your Kayfun and Russian will end up in a drawer.
They did last night, I needed the atty stands for the new tanks here on the one's showing up.
For the most part, single coil tanks are best with single coils. Dual coil tanks are best with duals. And in the case of the Estia, it should have 3
YMMV of course.
YMMV of course.
wow last time i checked this thread it was only on page 42
after my last failed attempt at getting the Mini myself, long story short US retailers dont ship SXmini to China
a fellow vaper in the states did me solid and ordered one for me and should be arriving sometime this week
time to catch up on this thread
after my last failed attempt at getting the Mini myself, long story short US retailers dont ship SXmini to China
a fellow vaper in the states did me solid and ordered one for me and should be arriving sometime this week
time to catch up on this thread
Quick question about the resistance reader on the SXmini.
I don't have a multimeter or an ohm reader (yet) and have only been running my Subtank. I am using the 1.2 coil that came with the Subtank, and when I first screw on the tank, the mini reads it correctly. After a few Vapes it drops down to 1.18 or 1.17 or 1.18 but never consistent. I unscrew the atty and push the fire button so it says 0.00 and then screw it back on and it reads correctly until my first vape.
Is this normal?
I realize I will eventually have to buy an ohm reader since my long term plan is to get into RTA/RDAs, but worried about the fluctuations. Although the guy at my local B&M said that the SXmini has one of the most accurate readers.
I don't have a multimeter or an ohm reader (yet) and have only been running my Subtank. I am using the 1.2 coil that came with the Subtank, and when I first screw on the tank, the mini reads it correctly. After a few Vapes it drops down to 1.18 or 1.17 or 1.18 but never consistent. I unscrew the atty and push the fire button so it says 0.00 and then screw it back on and it reads correctly until my first vape.
Is this normal?
I realize I will eventually have to buy an ohm reader since my long term plan is to get into RTA/RDAs, but worried about the fluctuations. Although the guy at my local B&M said that the SXmini has one of the most accurate readers.
It's normal, resistance changes with temperature, and the delay between removing it and putting it back on is long enough for that juice covered coil to cool back down and get you back to its "normal" reading. Nothing to worry about.
It never goes back to the normal 1.21 reading after its on and I'm vaping it - even if I let it sit for 20 mins.
Is the reader accurate enough that I don't need to invest in another reader/multimeter right away?
Look at the positive side, it's not a cigarette anymore and you're not burning down your house! [emoji4]
Yes dude, it is. And don't forget that resistance is added via the 510 connection as well, and removing a tank and putting it back on can change that value, and that 510 connection on the Kanger is spring loaded which can also complicate things.
The reality is, that variance between 1.21 and 1.18 is totally irrelevant at the low wattage you're likely to be using that 1.2 OCC at.
Awesome thanks bro!
I picked up a Magma clone (since the Aqua2 is in transit from FT) from my local Vape shop to start learning on - been reading a bunch so just had to ease my concern.
magma: very long 510 connection --> danger: don't try to screw it tight to the sxmini. don't force it. just screw till it makes contact
Ha,,we talk nearly every day on the phone and yes, you are right. She does possess mind control...
J/K we are good friends.
- Status
Similar threads
