- Status
you can see that crack. it doesn't go the whole way through. I think the acetone actually exposed a defect from the manufacturer.
my new one should be here by Friday. I guess you are supposed to boil the piece, then cool it, then it should come out.
my new one should be here by Friday. I guess you are supposed to boil the piece, then cool it, then it should come out.
Where did ya order the replacement tank? As i just recently had a banana mix that cracked my tank too. I think it is just fractured also, but i know that its time will come. Cant wait for a glass version to come out so we dont have to worry bout this.
Thanks in advance!
Thanks in advance!
evcigs in Florida had them for 5, but after shipping is like $7.80
Definitely should have ordered two but whatevs
Definitely should have ordered two but whatevs
I understand that. I'm willing to do it, though, if someone will tell me how. Obviously, others have done it, because we have pics farther down in this thread. (In fact, wasn't that you who showed images of that slanty hole inside the deck?) I have drilled mine out and the super-tight draw makes it practically unusable. So I don't figure I have much to lose. thanks....
Anybody know where to get the nano tank?
And is there a way to buy a Pyrex tank?
And is there a way to buy a Pyrex tank?
Is yours a clone? If so is it the hcigar clone (clone with extras and ® on the box)?
If it's the hcigar clone this might fix your problem without taking the base completely apart.....
Don't know if this has already been addressed (didn't read what came after this post) .. but there is a fix for the tight draw on the Hcigar TGT (Focalecig) .. the problem is the plastic insulator inside of the air hole (not the air tube). Pull out the plastic insulator inside the air hole in the base and trim off a little from the bottom and replace ... this should fix any problems with a tight draw.
Apparently there is a burr on the bottom of the plastic insulator that is blocking air flow regardless of which size air tube is used.
Found this little tip on Planetofthevapes site, as everyone was having a problem with the tight draw, and this was the across the board fix for it ... Am waiting for my Taifun now, and have been researching the hell out of it as I wait.
For knocking the chamber base out of the atty base this is my procedure....I take the coil attachment screws out, as well as the 510 screw/o-ring/spring/and insulator. Then I thread the base onto a ss tank, then I get a punch that fits tight in the empty 510 hole, and then give it a whack with a hammer. Not much to it.
that reminds me ................ i never heard back and then got caught up in odds and ends
Here's the taifun cotton build I've settled on
Thing works great with kanthal ribbon wire if you haven't tried it, the posts catch my thick 0.8x1mm ribbon it like its nothing. Takes a try or two to get the wick perfect, but its flawless when you get one working. The ribbon conventional coil seems to singe my wick after around 30mL, while I had to rewick every 10-15mL with 28ga round wire microcoils.
Thing works great with kanthal ribbon wire if you haven't tried it, the posts catch my thick 0.8x1mm ribbon it like its nothing. Takes a try or two to get the wick perfect, but its flawless when you get one working. The ribbon conventional coil seems to singe my wick after around 30mL, while I had to rewick every 10-15mL with 28ga round wire microcoils.
lol - never heard back from the glass factory
Oh...LOL... I was thinking, did I forget something...? They say the memory is the first to go... at least I think they say that, I can't remember.
Try "WARMING" the SS part a bit in water to expand it then press evenly. When it cools should really snug up. :thumbup:
Sent from Gallifrey using a Sonic Screwdriver via Tardis #5 :what:
I tried that while getting the replacement part very cold. Comparing the recessed part to my original tank, there is quite a difference
Oh sorry that was my only brainstorm. Maybe some emory cloth on the tank insert?
Sent from Gallifrey using a Sonic Screwdriver via Tardis #5 :what:
if the difference between the old and new one can still be shown in a picture i would approach the vendor ...........
- Status
Similar threads
- Locked
