Tfv4 tank
- Thread starter Vapevape
- Start date
- th_trl_thread_readers 0
- Status
picture from the side maybe?
There it is idk what im doing wrong.
Sent from my SM-G900P using Tapatalk
Sorry back together already i trimmed the wicks back again to see if i can get it to wick as fast as im vaping it
Sent from my SM-G900P using Tapatalk
Cant make this thing wick on its own like it should ive wicked it like every video ive seen nothing works. Omg help! Ive been doing thiss too long for this not to work.
Sent from my SM-G900P using Tapatalk
There it is idk what im doing wrong.
Sent from my SM-G900P using Tapatalk
view from the side?
I tried pushing the wick above the chanels more right now so good.
Sent from my SM-G900P using Tapatalk
Sent from my SM-G900P using Tapatalk
Yup no good have to open the top cap to forcw juice into the coils.
Sent from my SM-G900P using Tapatalk
The wick ends looks good. May want to try lowering the thickness of the wick. may help in better juice flow.
Its really not as thick as i.d of the coil it just fills out. Plus when ive used less wick it leaks and still doesnt wick properly.
Sent from my SM-G900P using Tapatalk
So i got it figured out finally only took since Saturday. I had to take little wisps of cotton and put it in the channels and lay the other end on the cotton thats through the coil. So that it could wick the juice up to the coils haven't had a burnt taste yet i have gone through 3 tank fulls. I feel so stupid but i found the solution on reddit.
Did you try the single rba that came with the unit? I just got mine yesterday and I'm thinking about trying it out later today. Should I dry burn it before I use it? This will be my first rba, so any tips are appreciated.
Glad you got it figured out. I love this tank so far. I've only used the stock triple so far.
I love it so far too I have had it for a little over 2 wks. I used the stock triple coil for 3 days and then through in the single rba deck, but because i dripped before this i needed the dual coil for my go to build. dual 24 gauge .25 ohms run between 40-60watts perfect. It just took me a little while to figure out the wicking of the dual coils now that i have it figured it out it works like a champ.
With anything you have to be patient and because i have been building for so long I figured it was like my Rda's which it isnt.
Good luck let me know if I can be of any assistance.
If you are going to just use the coil that is on there i would burn it a little before you wick it to be sure that you get any residue off the wire. With the single when you wick it be sure to have wicks in the channels it will help get that juice up to the coil. Be sure that you are using this tank on a regulated variable wattage/voltage device. I do not recommend using this on a unregulated mod.
Thanks for the tips. I put it on and pulsed it a couple of times. Watched a couple of videos and tried the wicking. I'm pretty impressed with it. Especially for my first go. I had been running the triple at 60 watts. I'm running this at 35 and getting better flavor and vapor. No dry hits yet. I'm going to pick up the dual rba base and a bigger mod soon.
Maybe I spoke a little soon. It just started leaking out the bottom. I'll redo the wicking again in a little bit. Maybe try and get a little more in the juice channels.
With the single never had leaking but have heard others have. Change the o ring on the bottom of the rba base. That could be why. Its a balnce have to have enough cotton but not too much.
Sent from my SM-G900P using Tapatalk
I think I had cut it a little short the first time. I made sure to stuff just a little bit down into the channels after I put the cap on this time. It hasn't leaked in about 12 hours so far. I did close the airflow when I went to bed, though. I'll see how it does today.
Isn't the gap between rda cap and the wall too narrow in tfv4 mini? I'm only using it with full version, it doesn't seem to have gap wide enough in mini version
Sent from cloud via xCube 2
Sent from cloud via xCube 2
had same problem as u.. if ur vg ratio is high, reduce the thickness of the wick.. if its leaking make sure to block the juice channel a lil bit.. mine solved after few trials.
- Status
