Just seen this from vaporjoes Kanger T3S base will allow you to use the T3S heads in the Kanger T3
- Status
That sure would be ideal and makes sense. As dealers start getting these, we should have a lot of posts from users soon to see whether these combinations really work. One batch of standardized Kanger heads with a few different clearo shapes sure would simplify things.
Edward at Sun-Vapors said the Evod and Protank coils will not work with the T3 tank, but he didn't seem to know if the T3S coils will work on the Evod and Protank. I'll find out when I get mine Tuesday.
Kanger T3S Atomizer Heads (5 Pack) (1 Base included temporarily) - Sun-Vapers.com
J.R.
Just got mine from Edward.
I've run into a bit of a snag. The new heads and base won't register on my eVic.
I'm guessing it's not making contact with the center post.
Everything else I've got (SVD, various Spinners and Twists) works fine with the new head/base.
I've tightened everything down VERY snugly but I won't force anything beyond finger-tight.
My guess, this is just an issue with the center pin on the eVic. I've never tried to raise that
center pin. That seems potentially disastrous.....
I've run into a bit of a snag. The new heads and base won't register on my eVic.
I'm guessing it's not making contact with the center post.
Everything else I've got (SVD, various Spinners and Twists) works fine with the new head/base.
I've tightened everything down VERY snugly but I won't force anything beyond finger-tight.
My guess, this is just an issue with the center pin on the eVic. I've never tried to raise that
center pin. That seems potentially disastrous.....
Vaping some Our Y Chai from Good Life Vapor on the new T3S base/coil. I'm using it on a plain ol' clear T3 body
attached to my SVD. It is GREAT. At least as good as the Evod and ProTank. Very similar draw, nice saturated
vape. I got no complaints!
One slightly odd thing though. I ordered 1.8Ohm heads and the SVD reads it as 2.8 or 3.0Ohms.
And it very clearly says 1.8Ohm on the head itself. I'm not complaining though. It's working fine.
No dry hits or anything. I've got my SVD set to 9W.
attached to my SVD. It is GREAT. At least as good as the Evod and ProTank. Very similar draw, nice saturated
vape. I got no complaints!
One slightly odd thing though. I ordered 1.8Ohm heads and the SVD reads it as 2.8 or 3.0Ohms.
And it very clearly says 1.8Ohm on the head itself. I'm not complaining though. It's working fine.
No dry hits or anything. I've got my SVD set to 9W.
I got mine a little bit ago, and it’s working great. No gurgling or dry hits so far. After using Evod tanks for the last three months, I almost forgot how big the T3 looks, but it’s really nice to be able to see my juice again. I’m looking forward to the clear mouthpiece tanks. I think a clear tank and mouthpiece on a chrome mod will look pretty good.
Only time will tell if it’s as low maintenance as the Evods have been for me, but so far I like it.
J.R.
Only time will tell if it’s as low maintenance as the Evods have been for me, but so far I like it.
J.R.
Great to hear the good responses so far. I think I'll hold out for a little bit but this is a great development. I don't understand why all the heads aren't identical with different tubes on top...
Edit: Just found these! http://www.discountvapers.com/search.php?search_query=t3s&x=-327&y=-84
Edit: Just found these! http://www.discountvapers.com/search.php?search_query=t3s&x=-327&y=-84
Last edited:
Somebody in the eVic section helped me solve this problem.
Pull the center pin on the coil head down just a TINY bit. I did it with the head screwed into the base so I could roughly gauge just how
far down it was. If you pull too hard you'll just yank that pin out, which isn't a big deal. It'll pop right back in.
But that solved the problem for me on the eVic. Been using it a few days now this way, no more problems and it's vaping great.
I hope that helps!
Pull the center pin on the coil head down just a TINY bit. I did it with the head screwed into the base so I could roughly gauge just how
far down it was. If you pull too hard you'll just yank that pin out, which isn't a big deal. It'll pop right back in.
But that solved the problem for me on the eVic. Been using it a few days now this way, no more problems and it's vaping great.
I hope that helps!
You're very welcome! It was another board member in another thread that schooled me on
this method so I can't take credit for it.
I can say, however, that even if you're kinda clumsy (because I am a TOTAL klutz) the heads will
probably survive. Like I said, even if you completely yank out that bottom post/plug, it goes right back
in easily and nothing is harmed.
I'm eager to try the "real" T3S, with the redesigned mouthpiece. I'm thinking it will be even better than
a retro-fitted T3....
this method so I can't take credit for it.
I can say, however, that even if you're kinda clumsy (because I am a TOTAL klutz) the heads will
probably survive. Like I said, even if you completely yank out that bottom post/plug, it goes right back
in easily and nothing is harmed.
I'm eager to try the "real" T3S, with the redesigned mouthpiece. I'm thinking it will be even better than
a retro-fitted T3....
Thanks for that Zipflint. That worked.
Just hope I don't destroy any heads with my brain surgeon like precision.
I'm digging the retrofitted MT3s I have, but 3 new actual MT3Ss are on the way too. Wonder if they'll have the same funk my T3s had when new...
I heard ivape had them via Facebook, haven't looked into it. Discount Vapers may have them, they have the whole units and coils.
Quoted from DiscountVapers
Compatibilities:
The Original T3 and MT3 bottom coil replacements with the permanent attached coil are compatible with the new T3s/MT3s Bases and coils you can use a new style or original style base/coil on either.
The MT3s and the T3s use the same replaceable Bottom coil.
You can use the T3s/MT3s coil on eVods and ProTank but you cannot use the eVod or ProTank coils on the MT3s or T3s
Sent from my iVap using Tapatalk HD
Compatibilities:
The Original T3 and MT3 bottom coil replacements with the permanent attached coil are compatible with the new T3s/MT3s Bases and coils you can use a new style or original style base/coil on either.
The MT3s and the T3s use the same replaceable Bottom coil.
You can use the T3s/MT3s coil on eVods and ProTank but you cannot use the eVod or ProTank coils on the MT3s or T3s
Sent from my iVap using Tapatalk HD
- Status
Similar threads
