The Official Nicoticket " Get the most from your juice thread."
- Thread starter distortoblotto
- Start date
- th_trl_thread_readers 0
- Status
I have a copper Mutation X sitting on top of a copper Oro with dual 2 mm 28g's built to 0.50 ohms with KGD wicks and it sizzles a bit but it doesn't spit. With a fresh battery at 4.2 volts, that puts me right at 35 watts. My suspicion is that you have your coils too low to the deck. Try raising them a bit and see if that helps. Are you using big diameter coils?
As Distorto mentioned, it sounds like a build issue you are having mah friend.
I plugged your .41 twisted into Steamengine.org and ran the numbers. You are boiling your juices mah friend...that's where the spitting is coming from not the pg/vg ratio. Here is a screen shot. Pay particular attention to the Results box on the right. At 45 watts 487 mw/mm2. That is smoking hot, even for me and I run my builds in the 300 range...
Here's a link to State o' Flux's blog on some of the particulars of the Steamengine.org program and how it can help you achieve a better vape! It comes in 2 parts...
http://www.e-cigarette-forum.com/fo...steam-engine-basic-use-advanced-features.html
http://www.e-cigarette-forum.com/fo...ne-basic-use-advanced-features-part-deux.html
I am just beginning to play with my builds, and STILL waiting on a massive Kanthal order from Temco Mitro, so in mah downtime I have been researching everything build related I can. I think this may help you enjoy your NT juices.
Bottom line, your builds are too hot.
Well, look what the cat drug in!....Howdy there Spike! How are you doing my friend?. The stock coils can be rebuilt but you have to get the right diameter and with to fit down the shoot. Me thinks you will be a happy camper with the Nano.
As Distorto mentioned, it sounds like a build issue you are having mah friend.
I plugged your .41 twisted into Steamengine.org and ran the numbers. You are boiling your juices mah friend...that's where the spitting is coming from not the pg/vg ratio. Here is a screen shot. Pay particular attention to the Results box on the right. At 45 watts 487 mw/mm2. That is smoking hot, even for me and I run my builds in the 300 range...
Here's a link to State o' Flux's blog on some of the particulars of the Steamengine.org program and how it can help you achieve a better vape! It comes in 2 parts...
http://www.e-cigarette-forum.com/fo...steam-engine-basic-use-advanced-features.html
http://www.e-cigarette-forum.com/fo...ne-basic-use-advanced-features-part-deux.html
I am just beginning to play with my builds, and STILL waiting on a massive Kanthal order from Temco Mitro, so in mah downtime I have been researching everything build related I can. I think this may help you enjoy your NT juices.
Bottom line, your builds are too hot.
Nice one my Brother!! I see you've been doing your homework. Good on ya!
Good man....
So run it at a lower wattage or? Cuz even the .8 single twisted sizzles snd spits a hair on warmup.
Nice one my Brother!! I see you've been doing your homework. Good on ya!
Thanks DB!
I highly recommend that ANYONE who builds their own atty's, read the State O' Flux blogs on one tab and have Steamengine.org on another tab and experiment and practice while reading the blog.
It is put in really simple language and will only enhance your experience with SE.org. I've been using the heat flux function for a while but never thought as So'F suggests, to build from a heat flux that you enjoy...
I'm hoping that Dampmaskin will create a simple input method for complex (zippers, claptons etc...) coils without having to measure all the wire and do the math.
Are you using Steam Engine when you calculate your build? Let's start there.
Jeffery, If you don't mind and if you are able, Post a close up picture of your build and we can take it from there. I only post this to help you get to the right place so you can enjoy that jooz...
A lower setting will work but when I want to really blow clouds, I'll go down as low as 0.3 ohms with big coils on a mech and still not have the problems you are experiencing.
A lower setting will work but when I want to really blow clouds, I'll go down as low as 0.3 ohms with big coils on a mech and still not have the problems you are experiencing.
Here's what your numbers look like...
My builds spit and pop at 277. Try around 25 watts to avoid the spitting and popping.
Jeffery, If you don't mind and if you are able, Post a close up picture of your build and we can take it from there. I only post this to help you get to the right place so you can enjoy that jooz...
A lower setting will work but when I want to really blow clouds, I'll go down as low as 0.3 ohms with big coils on a mech and still not have the problems you are experiencing.
I'd take a pic but wife is sleeping next to me in bed and I don't wanna wake sleeping beauty lol.
You are gonna have a WHOLE new vaping experience. Check out those 2 blogs and you can begin to customize your vape your way. Not to discount the inventor, here is his blog pertaining to his program, also some valuable insight as well...sorry about the light reading
http://www.e-cigarette-forum.com/forum/blogs/dampmaskin/5833-steam-engine-vape-calc.html
What does the strands mean?
And for the dual coil twisted idk if I'm doing something wrong but it says at 50watts it'd be 139.
I got the same conclusion on the single twisted as you did Though.
And for the dual coil twisted idk if I'm doing something wrong but it says at 50watts it'd be 139.
I got the same conclusion on the single twisted as you did Though.
I want to be using these things! or at least try them out. I keep adding them to my pretend cart and then moving back to my wishlist. LOL
big Kanger fan as well- when I knew it was time to switch back, Kanger was the only clearo/tank I would even look at. if I'm this impressed with the Aerotank Mow Mega, I'm sure I'll dig the Subtank!
- Status
Similar threads
