THE Phoenix Line is here & up for SALE. both phoenix xl & 3ml tank version,bottom coil, 2 ohms for both

[sparkyth67]

Steve K had that happen to him and it messed up his Provari to where he couldn't set the volts. If you should have any problems you may want to look at his experience and solution. Scary ProVari Cleaning Advice

Errol

Thanks for the tip much appreciated

 

[badkolo]

a phoenix on a stick style is loveeeeee

have one on a joye auto and one on a joye manual 510 stick and wowowow

 

[Errol]

[/QUOTE and I still don't understand why VG gives more vapor when i believe it is PG that is actually used in fog machines of course I could be wrong there[/QUOTE]

I've tried so many different combinations lately that I'm not really sure myself at the moment.

I pulled a CE3-XL apart and am using it as a dripper with excellent vapor but not sure what combination of PG/VG I'm using. A little later I'll try some 18mg PG and then VG niquid without flavoring to see if I can see a meaningful difference and report back.

For anyone still having problems and not sure if it wicking or the coil you may want to try pulling the center post and dripping three or four drops directly into the tube and see how the coil is working. I put about 8 drops in and lay it on it's side, tipping it upright for a moment when the vapor starts waning.

Errol

 

[kwcharlie]

OH YES, this workd and a lot easer than groving out with the exacto knife like the older ones

OK, done this to 2 of them so far. Great vape, flavor, no leaking, no dry hits.
1) remove mouth piece, use a paperclip

2) remove inner silicone seal that is contacting the stem (pay attention to the orientation, concave part faces mouth piece) used a paperclip in the fill hole.

3) use small pliers to pull the stem up about 1/10 of an inch

4) replace seal with in proper direction.

5) chain vape


Here:

modded is on the left, factory is on the right:

View attachment 96892

Cool?

Here's another pic if you can't see that:

View attachment 96893

 

[badkolo]

what would be nice is to make that inner post screwable into the base it sits in with the wick
this way it can be self adjusted depending ont he juice being used, wicks to much screw it down more, doesnt wick enough then unscrew it a tad to match the pcis above.

 

[Big Screen D]

what would be nice is to make that inner post screwable into the base it sits in with the wick
this way it can be self adjusted depending ont he juice being used, wicks to much screw it down more, doesnt wick enough then unscrew it a tad to match the pcis above.

Bad, if you're familiar with the Odysseus Atty, that is exactly how it works. Now don't go getting any ideas and get all ridiculous with the price, but that atty is like 100x more expensive! And you know what, you'd have essentially the same thing.

 

[Cyrus Vap]

Its still cranking! I've lost count, and that's good

so why does removing wick = lifting the post? that is the question...

 

[sparkyth67]

well after trying once again it is ok on provari @3.7 and it is ok on my ego except no throat hit flavor is ok at best but at higher voltages nothing but dry hit and burning juice taste si either the phoenix are useless to me or my provari is useless to me and I paid way too much for it to say that

 

[hdzrtvap]

I'm am proud to say i have filled number 3 same as # 1 & 2 right from the box and having no problems what so ever.

Note: in the picture below i see that No. 1 & 2 have the spacing in the little notch the same as the picture on the right, # 3 looks just like picture on the left and all 3 are right from the box. all 3 seem to work the same and all using 70/30 mix now.

# 2 and 3 are on their 2nd fill. using all 3 on KGO's

 

[Cyrus Vap]

well that's interesting....

 

[kwcharlie]

what would be nice is to make that inner post screwable into the base it sits in with the wick
this way it can be self adjusted depending ont he juice being used, wicks to much screw it down more, doesnt wick enough then unscrew it a tad to match the pcis above.

YES, just tried it with the 3ml, changed it. something to adjust that window into the bottom coil IS THE ANSWER

 

[Aras]

well after trying once again it is ok on provari @3.7 and it is ok on my ego except no throat hit flavor is ok at best but at higher voltages nothing but dry hit and burning juice taste si either the phoenix are useless to me or my provari is useless to me and I paid way too much for it to say that

After pulling the stem up a tiny bit like my pics, vaping at 4.5v on a provari, no leaks, no dry hits. Chain vaping while watching a movie. I gave a pack to my buddy, showed him what to do if he gets dry hits. He and his GF texted me to say thank you. I had them using ce2's before this and he always had problems. He's very happy with these. So am I. Maybe he will put analogs down for good now!

 

[sparkyth67]

After pulling the stem up a tiny bit like my pics, vaping at 4.5v on a provari, no leaks, no dry hits. Chain vaping while watching a movie. I gave a pack to my buddy, showed him what to do if he gets dry hits. He and his GF texted me to say thank you. I had them using ce2's before this and he always had problems. He's very happy with these. So am I. Maybe he will put analogs down for good now!

well I may give your trick a try on one when I have time but I just don't like to have to fiddle with something that was passed as performing perfect as is I can see maybe 1 or 2 here and there but out of first box all 4 tried have been the same and that is a bit deflating

 

[harmonic]

DIFFERENT SIZE GROVES IN THE CENTER POST!!!! then you just turn it to the desired opening size and pop it in - simple selectable opening sizes yea that's it

 

[timothy]

DIFFERENT SIZE GROVES IN THE CENTER POST!!!! then you just turn it to the desired opening size and pop it in - simple selectable opening sizes yea that's it

That was what I was thinking a sideways v

 

[ambientech]

well I may give your trick a try on one when I have time but I just don't like to have to fiddle with something that was passed as performing perfect as is I can see maybe 1 or 2 here and there but out of first box all 4 tried have been the same and that is a bit deflating

I am sure we all wished it was that simple but it isn't. Juice comes in all different consistencies. PG and VG isn't the only thing that affects wicking.

 

[melloyello]

one another note, the screw on cap that comes with the 3ml phoenix can be screwed on and looks nice on an ego/kgo battery....if you dont have another place for it ofcourse...like on the 3ml carto

 

[ambientech]

what would be nice is to make that inner post screwable into the base it sits in with the wick
this way it can be self adjusted depending ont he juice being used, wicks to much screw it down more, doesnt wick enough then unscrew it a tad to match the pcis above.

This is what I am talkin about!! I could unscrew it enough to flood it so it will take 10 watts

 

[melloyello]

2nd day, these things are still running like new. no leaks whatsoever, huge vapor and throat hit....not even one gurgle along the way so far. i have gone through 6 fills so far. with a boge carto, tomorrow i would have to open up a new one. my battery is also lasting couple hours longer vs using a 2.0 boge.

 

[Aras]

well I may give your trick a try on one when I have time but I just don't like to have to fiddle with something that was passed as performing perfect as is I can see maybe 1 or 2 here and there but out of first box all 4 tried have been the same and that is a bit deflating

There is less fiddling with these than any other fillerless carto I've tried. I know your pain, ask badkolo. I've blown him up repeatedly for selling things to me that didn't work. I don't like being a part of R&D and paying for it either. I feel like these actually work compared to previous products, x7, ce2's over and over and over, and many other carts. A little fiddling is better than smoking polyfill imho. All you need to do is grab a pair of pliers and pull the stem up 1/10". It's really simple.