I am pretty sure I can fix it . The post with the gasket on it is the positive . If you dont want to mess with it send it in
The "REOMIZER" Rob's Rebuildable Atomizer
- Thread starter rasci2
- Start date
- th_trl_thread_readers 0
- Status
Oops....I mean the positive post! I'll mess with it if you'll tell me what to do.
After attempting your free hand coil wrap method, I am now positive you have magic in those hands!
You were right I dont no what I was thinking . the top plate on the atty is the positive so the post with the gasket is the negative . It sounds to me like the short is coming from the negative post . If its lose I would snug it down and test it with your ohm meter .I try to never grab the atomizer by the posts but by the base if possible
You get use to it I use to do it with a small piece of copper wire but I realized it didn't need it and have done them free hand ever since
This place is gettin' to be like reading Penthouse Forum. I'm not sure my delicate sensibilities should be exposed to this.
Jack
Anyone having trouble with the o-ring not sealing the cup?
That & the small 32 ga. wire have given my 63 year old eyes a little trouble.
Am now using 28 or 30 ga. wire & it works fine on my grand.
That & the small 32 ga. wire have given my 63 year old eyes a little trouble.
Am now using 28 or 30 ga. wire & it works fine on my grand.
The o-ring in the catch cup?
No problems with that here. What's happening?
I snugged it down, built another coil, zero ohms. Noticed a tiny bulge in the gasket that sits close to the threads. When I tried to attach the cap, the tiny bulge got caught and broke. Sending it to the ICU...was shipping you a package today anyway.
I always grab it by the base.
Last edited:
I will find the culprit
Hello Louis this happens to me a couple times a week . I think were just giving the atomizer a little to much juice it only takes a couple drops to fill whats left of the juice well . I remove my atomizer clean the bottom with a paper towel and I soak up the juice in the well . Install the rba and I can go days without it a curing again so I no its me
Last edited:
got mine!!!!!!!!!
i will defenetly be getting myself set up with a few of these in the futer... before trying it out i removed the rob rolled coil. and did my best to duplicate it.......
ive got some learning to do but im loving the flavor/vapor production and hitt.........
home run bud.
i got this for my self as my B day gift. it may just turn out to be my new go to atty.
(its nice to have my grand back as well) repair/rebuild kits rock!!!! nice job mod master rob...
thank you..
i will defenetly be getting myself set up with a few of these in the futer... before trying it out i removed the rob rolled coil. and did my best to duplicate it.......
ive got some learning to do but im loving the flavor/vapor production and hitt.........
home run bud.
i got this for my self as my B day gift. it may just turn out to be my new go to atty.
(its nice to have my grand back as well) repair/rebuild kits rock!!!! nice job mod master rob...
thank you..
I've found the Reomizer WAY easy to over-squonk. Since my drip tip comes off easily, I've started to take it off and look down into the atty while squonking. Squeezing the bottle till I just see a bead of liquid reach the wick legs is all it takes to get a good three to four vapes. Of course this is not recommended while driving, but it has eliminated the messy overflowing catch cup syndrome.
Late to the party:
I received on of these gorgeous babies in the mail yesterday. Awesome work as usual Rob!
I do have a quick question for the pros here. I scanned through the thread but didn't notice it coming up:
Is it possible to tighten the draw a bit? If I dropped some additional wicking material under the bridge, would it make any difference?
I received on of these gorgeous babies in the mail yesterday. Awesome work as usual Rob!
I do have a quick question for the pros here. I scanned through the thread but didn't notice it coming up:
Is it possible to tighten the draw a bit? If I dropped some additional wicking material under the bridge, would it make any difference?
I know it's not pretty, but here's an option for you. Cut the end off a carto condom and slide it partially over the hole.
Genius! Thank you so much. I was just scrabbling around my desk looking for something similar. Never even occurred to me to hatchet up a condom.
Then again, as a single 41 year old dude: it should NEVER occur to me to hatchet up a condom.
Sorry: couldn't resist.
Then again, as a single 41 year old dude: it should NEVER occur to me to hatchet up a condom.
Sorry: couldn't resist.
No condom in my desk at work sadly, in a pinch...the sticky portion of a post it note works great!
No condom in my desk at work sadly, in a pinch...the sticky portion of a post it note works great!
A piece of scotch tape works also. Not pretty but it works.
I'm all about function over form in this case. Works great! I'm really digging this puppy. Just using Rob's wick right now, my adventure in wick making begins this weekend.
- Status
Similar threads
