The WetBox Coming This Week to Clouds of Vapor!
- Thread starter Bigbuyer
- Start date
- th_trl_thread_readers 0
- Status
The Black 510 Cartomizer WetBox and the Black KR808 Cartomizer WetBox has been added to Clouds of Vapor. If you want to know when I have them, log in and click on the "notify me" button next to each product. You will get an email letting you know.
Got mine today and did a write up in an email. Thought I'd just copy/paste it here:
Btw, I got the wetbox today. Pretty simple and frankly one of the better solutions I've seen for dispensing ejuice. There's a blunt needle top to the 3ml translucent bottle. Don't know if that is made or an already premade part. the batt connection is not recessed - that will help with any leaks - so far none - and it [batt connection] is set in place with a lot of epoxy around and below it ... but there's a small 'channel' which the needle tip goes through and out the center hole of the battery connector. So it sticks up above the connection about 3/8 of an inch. I'm guessing this is an exact measurement when making it, as it then penetrates the center hole in the cartomizer. She likely knows how far she can go into the cartomizer without contacting the 'stuff' - electronics, coil, etc. (well, I'm guessing that's the case. It may have been just trial and error). But there isn't any aspiration?/atomizing into the atty chamber like their would be in other setups I've seen. So, the fluid it likely going into the filler around the coil. Bottom feeding (filling from the batt end) isn't usually recommended but many do it without problem but here, since the needle goes quite a ways into the cartomizer the problem of it leaking back out is reduced, imo.
In practice, once I notice a drop in flavor (a key factor in maintaining a good life of a cartomizer), I give one pump and the flavor is back instantly and for a good cigarette's worth in time - much like dripping, really. I overpumped it just to see what might happen and no leaks - a bit of gurgle - and a puff of vapor out of the drip tip I'm using on the carto. I take the tip off and there is no 'puddling' on the cart side so it's getting absorbed well by the filler.
There's no 'underflavor' going on - that I get with many prefilled cartos and so the blank cartomizer is a must, imo, and there is nothing special about the cartomizer. Standard type as far as I can see and I'm going to try some of Drew's 'mega' 510 cartos after a bit. ....measuring... in fact, that appears to be what she is using - it's the same size as one I have from Drew. Wondering now where she gets them. I'll email her. Really decent vapor too. I'm wondering if it is a 'mega premier' (the premier line at V4L has a 2.3 ohm atty instead of the more usual 3.x ohms in most cartomizers. I'll ask her that as well. The only possible problem is that cartos tend to burn their fillers - they're wrapped right around the coil basically. I'm not that concerned - the wicking in a 510 can get that way as well although with cleaning or in a peak volt mod that buildup gets burnt off. The key is to keep everything wet.
It's a 14500 batt and the activator button is a small one on the side - a Bartleby big bottom button is simply impossible due to the physics, and it's on same side as the opening for 'pumping' (a half moon cut out of both sides of the case. The button is an easy reach even holding the mod horizontally, nicely placed. It has an on/off switch and the only thing keeping it from being 'perfect' is Jay's charging board and cable. lol.
I got mine in black and it has a 'sandy rough' finish which is rather nice. I've had it for less than 5 hours now and it's still doing fine. I'm staying off my other mods for now and I simply won't finish the 3ml of juice (DV's Absinthe in VG) today. And another reason I like the 14500 - it still hasn't lost it's peak voltage after almost 5 hours. I knew this from earlier trials - the output curve holds up better than any other batt I've tried - about until it goes outm which for me, will be in about another 2-3 hours. The Tornado/eGo batt is stronger than the 10440 - d'uh, the regular 510s and megas, but it loses a peak voltage about 3.5 hours into a new charge and then finishes in about another 3 hours for me, ymmv, and it still finishes stronger than a regular 510 or mega but the curve drop-off is evident to me anyway. Not with the 14500 though.
I may just copy paste this for a 'review'.
And I did. ;-)
Btw, I got the wetbox today. Pretty simple and frankly one of the better solutions I've seen for dispensing ejuice. There's a blunt needle top to the 3ml translucent bottle. Don't know if that is made or an already premade part. the batt connection is not recessed - that will help with any leaks - so far none - and it [batt connection] is set in place with a lot of epoxy around and below it ... but there's a small 'channel' which the needle tip goes through and out the center hole of the battery connector. So it sticks up above the connection about 3/8 of an inch. I'm guessing this is an exact measurement when making it, as it then penetrates the center hole in the cartomizer. She likely knows how far she can go into the cartomizer without contacting the 'stuff' - electronics, coil, etc. (well, I'm guessing that's the case. It may have been just trial and error). But there isn't any aspiration?/atomizing into the atty chamber like their would be in other setups I've seen. So, the fluid it likely going into the filler around the coil. Bottom feeding (filling from the batt end) isn't usually recommended but many do it without problem but here, since the needle goes quite a ways into the cartomizer the problem of it leaking back out is reduced, imo.
In practice, once I notice a drop in flavor (a key factor in maintaining a good life of a cartomizer), I give one pump and the flavor is back instantly and for a good cigarette's worth in time - much like dripping, really. I overpumped it just to see what might happen and no leaks - a bit of gurgle - and a puff of vapor out of the drip tip I'm using on the carto. I take the tip off and there is no 'puddling' on the cart side so it's getting absorbed well by the filler.
There's no 'underflavor' going on - that I get with many prefilled cartos and so the blank cartomizer is a must, imo, and there is nothing special about the cartomizer. Standard type as far as I can see and I'm going to try some of Drew's 'mega' 510 cartos after a bit. ....measuring... in fact, that appears to be what she is using - it's the same size as one I have from Drew. Wondering now where she gets them. I'll email her. Really decent vapor too. I'm wondering if it is a 'mega premier' (the premier line at V4L has a 2.3 ohm atty instead of the more usual 3.x ohms in most cartomizers. I'll ask her that as well. The only possible problem is that cartos tend to burn their fillers - they're wrapped right around the coil basically. I'm not that concerned - the wicking in a 510 can get that way as well although with cleaning or in a peak volt mod that buildup gets burnt off. The key is to keep everything wet.
It's a 14500 batt and the activator button is a small one on the side - a Bartleby big bottom button is simply impossible due to the physics, and it's on same side as the opening for 'pumping' (a half moon cut out of both sides of the case. The button is an easy reach even holding the mod horizontally, nicely placed. It has an on/off switch and the only thing keeping it from being 'perfect' is Jay's charging board and cable. lol.
I got mine in black and it has a 'sandy rough' finish which is rather nice. I've had it for less than 5 hours now and it's still doing fine. I'm staying off my other mods for now and I simply won't finish the 3ml of juice (DV's Absinthe in VG) today. And another reason I like the 14500 - it still hasn't lost it's peak voltage after almost 5 hours. I knew this from earlier trials - the output curve holds up better than any other batt I've tried - about until it goes outm which for me, will be in about another 2-3 hours. The Tornado/eGo batt is stronger than the 10440 - d'uh, the regular 510s and megas, but it loses a peak voltage about 3.5 hours into a new charge and then finishes in about another 3 hours for me, ymmv, and it still finishes stronger than a regular 510 or mega but the curve drop-off is evident to me anyway. Not with the 14500 though.
I may just copy paste this for a 'review'.
And I did. ;-)
Nice review. It comes down to one thing IMO. It's just so easy and convenient.
OT: BTW, I am a big DV Absinthe fan, where'd you get it in VG? PM me if you don't want to answer here.
OT: BTW, I am a big DV Absinthe fan, where'd you get it in VG? PM me if you don't want to answer here.
Thanks. Still going strong. I just might vape the whole 3ml
PM'd you on the DV VG...
They are on the way...20 boxes just for starters.
10 black 501
4 Black KR808
2 Brown 510
2 Rust 510
1 Green 510
1 Sand 510
10 black 501
4 Black KR808
2 Brown 510
2 Rust 510
1 Green 510
1 Sand 510
**********OT**********
When do expect an new supply of Rath Blueberry Pancake to come in? Also, will you be offering a lower nic level in your Rath line-up????
Thanks HUN!!!
When do expect an new supply of Rath Blueberry Pancake to come in? Also, will you be offering a lower nic level in your Rath line-up????
Thanks HUN!!!
I have a new order of Rath Juice coming. I will have Blueberry Pancake in 16mg and 24mg. No plans for lower nic at this time.
Only 6 left! More are coming.
3 Black KR808
2 Brown 510
1 Rust 510
3 Black KR808
2 Brown 510
1 Rust 510
Last edited:
Pardon my math, but 3 + 2 + 1 looks like 6 to me.
Spent my best 3 years in 5th grade so I gotta be able to add.
Spent my best 3 years in 5th grade so I gotta be able to add.
I understand this wetbox uses a cartomizer... Is it possible too use a standard 510 atty as I have heard that the 510 cartomizers are melting.. I love the way the side is cut out on the box... awesome design.. I want one.
So I got mine yesterday... WOW... This the best PV I have ever used.. I wanted to buy more than one but the site would not let me... I plan on buying a backup, cause my ego, v4l batteries and 510 batteries are now going to collect dust ....
Does anyone make low resistance 510 cartomizers? They are they only thing that I can think of that would improve a wetbox.
I have not seen a LR Cartomizer. My 510 Soft Tip Cartomizers test out at 2.8 - 3.0 oHm.
- Status
Similar threads
- Locked
- Locked
