This is not a pipe...

[bapgood]

........I'm at a loss for words.....that is awesome!!!

I WANT ONE!!!.....Please

 

[bzmotoninja83]

i can dig it. vape like a Sir!

 

[kevbow]

That is amazing slopes. Excellent job.

 

[aziffel]

Niiiice!.......

 

[asdaq]

Elegant in its simplicity and I like how it vapes out both ends, but is the vape running through all the innards or is there a tube to keep it orderly? I can't imagine a few days of condensate all over the electronics being appealing to get into.

 

[slopes]

Elegant in its simplicity and I like how it vapes out both ends, but is the vape running through all the innards or is there a tube to keep it orderly? I can't imagine a few days of condensate all over the electronics being appealing to get into.

There's a air/vape tube running from the coil through to the bowl - so it bypasses all the innards.

 

[Phantom309]

awesome pipe! I had to start over on mine it cracked across the middle of the bowl. I had to go back to the drawing board on it. I like touch switch set-up.

 

[k3vin]

Man video won't load in my phone.. Ugggg

 

[slopes]

awesome pipe! I had to start over on mine it cracked across the middle of the bowl. I had to go back to the drawing board on it. I like touch switch set-up.

Keep at it Phantom309... you're doing a grand job. I don't think my effort would be possible using wood. The body is epoxy.

 

[Lance_Wallen]

you're right, that's not a pipe... it's art. Amazing work, absolutely amazing.

 

[Phantom309]

Keep at it Phantom309... you're doing a grand job. I don't think my effort would be possible using wood. The body is epoxy.

Thank you Slopes, I actually wanted to get out there today and work on it but the weather was crappy. I'll post picks of the new one when I get it.

 

[0161Badger]

Great stuff most impressed ,Well done

 

[Zerrrro]

My father used to smoke a pipe years ago, and I still have a bunch of them. I need this and some Capt. Black Gold e-liquid. Nostalgia bomb!

 

[Chris153]

I am really digging this one. Looks awesome.

 

[Fesso]

Hey slopes I highly recommend you try some pipe-sause for your pipe.
EPipeMods/ E-liquid/ E-juice
They have sample packs available again. Check out their pipes too in case you haven't seen them already.

 

[slopes]

Hey slopes I highly recommend you try some pipe-sause for your pipe.
EPipeMods/ E-liquid/ E-juice
They have sample packs available again. Check out their pipes too in case you haven't seen them already.

Thanks for the tip Fesso. Their pipes are pretty cool. The juice looks classy - but I usually go for tobacco flavours.

 

[dirquist]

Thanks for the tip Fesso. Their pipes are pretty cool. The juice looks classy - but I usually go for tobacco flavours.

All of their juices are tobacco flavors. Two are straight tobacco, Long Bottom Leaf and Shire Malt. The reset have a tobacco base with flavors.

 

[asdaq]

Slopes, I like the touch switch setup you have here, have you got a pic of the lip sensor? I've never liked my cigar attempt on account of the bottom fire switch, it looks like holding a microphone rather than a cigar. I've made many changes but such a lip activation might actually just do it for me.

 

[beckyblue]

Both ridiculously impressed and missing my grandfather at the same time. Thanks for showing this to us, slopes! (Gads, not implying that you're even anywhere close to my granddad's generation, just that he was never without a wonderful, aromatic pipe in his hand!)

 

[slopes]

Slopes, I like the touch switch setup you have here, have you got a pic of the lip sensor? I've never liked my cigar attempt on account of the bottom fire switch, it looks like holding a microphone rather than a cigar. I've made many changes but such a lip activation might actually just do it for me.

Hi asdaq - the lip sensor is a bit of stainless steel wire resting about 0.5mm back inside the end of the aperture. I used a 100M ohm resistor on the circuit - so it's sensitive enough to activate when the mouthpiece area is moistened. I had planned to run the wire out of the bottom to a metal surface contact - but it doesn't need it.