Tootle Puffers, Part Three! (The Sequel of the Redux)

RainSong

An adult who likes flavors.
ECF Veteran
Verified Member
Sep 11, 2016
2,018
12,492
47
Tempe, Arizona, United States
Sometimes scanning takes a while to catch up. Depends how the upload is done. Or you could learn some patience
Patience and vape mail only exist in limited quantities.
 

Cosmic_Glaze

Super Member
ECF Veteran
Verified Member
Jul 26, 2016
948
3,828
Might be your coil is touch low, that can cause a slow seep on near any bottom coil tank. Or a wicking issue.

juice level in all steel config.... uh, dry hit? I don't vape crackers, so most of mine are transparent center. The ones that aren't are full clear M5 (which makes for a really light weight setup!)

Ya, I had to dremel out a couple of the FT bases, even for the 65pg I mix. Never had an issue with any of my EHPros.
It's leaking from the juice port...where you fill it.. not the air flow hole..there is no screw for it you just push the tip in it and fill..only tried that once kinda made a mess, then I have top filled since.. it's a very slow leak from the seal in it...never had to fill a device like this before... nor have I not had the option of a glass tank to throw any juice in it (menthol)
 

RainSong

An adult who likes flavors.
ECF Veteran
Verified Member
Sep 11, 2016
2,018
12,492
47
Tempe, Arizona, United States
It's leaking from the juice port...where you fill it.. not the air flow hole..there is no screw for it you just push the tip in it and fill..only tried that once kinda made a mess, then I have top filled since.. it's a very slow leak from the seal in it...never had to fill a device like this before... nor have I not had the option of a glass tank to throw any juice in it (menthol)
See, wonky leaks on these things ;) One of mine is leaking from the 510 pin. The other one luckily is working fine without leaks. One of my advs has cinnamon in it, so I haven't had it since I started running this tank. Even though it looks a little silly sitting on top of a Pico that's where it is. Until my wandering package gets here anyway.
 

Sugar_and_Spice

ECF Guru
ECF Veteran
Verified Member
Sep 11, 2010
13,663
35,225
between here and there

DPLongo22

"Vert De Ferk"
ECF Veteran
Verified Member
Dec 17, 2011
32,968
182,764
Midworld
I don't vape crackers

WAIT! We can do that?? And you waited until NOW to tell me?!?!?!?!?!

I LOVE SALTINES! :banana:

800b1f01-fd4b-4541-aeea-a3597a80b580.JPG.web.jpg
 

RainSong

An adult who likes flavors.
ECF Veteran
Verified Member
Sep 11, 2016
2,018
12,492
47
Tempe, Arizona, United States
Last week a buddy of mine let me play around with his Rig V1 mech mod for a couple of days to see if I liked it and wanted to buy one..... put in an order for the COV 1.5 Kindred this morning... 18650 & 18350 mode.. My first mech..:)...(yes, I know how to use one and have done months of research... battery safety, builds, ohms law...);)
View attachment 643845
I love this form factor, I'm just a nervous nelly. I need to start doing the research so I can expand into mechs.
 

Cosmic_Glaze

Super Member
ECF Veteran
Verified Member
Jul 26, 2016
948
3,828
I love this form factor, I'm just a nervous nelly. I need to start doing the research so I can expand into mechs.
I've been looking into it for awhile... the way I build I'm not actually pushing the envelope and stressing batteries with my builds...I made sure the one I got had proper venting, a lock on the fire switch, and a not hybrid connection.. I was just looking for something that was going to last a long time...
 

Plettschner

Ultra Member
ECF Veteran
Verified Member
May 2, 2013
1,085
5,979
CT
It's leaking from the juice port...where you fill it.. not the air flow hole..there is no screw for it you just push the tip in it and fill..only tried that once kinda made a mess, then I have top filled since.. it's a very slow leak from the seal in it...never had to fill a device like this before... nor have I not had the option of a glass tank to throw any juice in it (menthol)
Juice port? You mean that unused hole on the bottom? :D

If it's the kind with an o-ring, is the o-ring damaged or missing?

ETA:
Wait, a no screw kind of fill port... like a check ball valve? Maybe take it apart and clean it good... push check ball in and run water through it in case of a pice of dirt on seat. Worst case, clean it good and epoxy it closed.
 
Last edited:

Cosmic_Glaze

Super Member
ECF Veteran
Verified Member
Jul 26, 2016
948
3,828
Juice port? You mean that unused hole on the bottom? :D

If it's the kind with an o-ring, is the o-ring damaged or missing?

ETA:
Wait, a no screw kind of fill port... like a check ball valve? Maybe take it apart and clean it good... push check ball in and run water through it in case of a pice of dirt on seat. Worst case, clean it good and epoxy it closed.
Yeah it's different than the KF lite and the all others 3 holes on the side air flow, airflow control screw, useless port for filling and you can't easily access the inside of it or take it apart...... bet they thought this was a revolutionary game changer back in the day!!! ....Lol:p Putting a permanent seal and using the top fill method on it would work...
 

Katdarling

I'm still here on ECF... sort of. ;)
Supporting Member
ECF Veteran
Verified Member
Jan 25, 2011
32,582
167,751
Utopia
"Mamu-Mamu."

tumblr_mun7q6exug1s9btcio1_500.gif


MARVELOUS!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!


I tighten up good and tight :)




FYI: If Ya' was a really old timer or "Verified" you would know right now it's an acceptable "Mamu-Mamu" . . . :pervy: :lol: :lol: :lol:

;) :thumb: ;)



Subliminally speaking, of course. :D

Oh hellsbells...... nothing subbalimminall about it. :D


Or you could learn some patience

Hahahhahaaha! WE ARE VAPERS.



WAIT! We can do that?? And you waited until NOW to tell me?!?!?!?!?!

I LOVE SALTINES! :banana:

800b1f01-fd4b-4541-aeea-a3597a80b580.JPG.web.jpg


LOVE 'em too! LIVE on 'em!!!! Don't touch my krackers.
 

sorrynomore

Ultra Member
ECF Veteran
May 4, 2014
2,383
11,115
Canada
It's leaking from the juice port...where you fill it.. not the air flow hole..there is no screw for it you just push the tip in it and fill..only tried that once kinda made a mess, then I have top filled since.. it's a very slow leak from the seal in it...never had to fill a device like this before... nor have I not had the option of a glass tank to throw any juice in it (menthol)

maybe try this...
Kayfun Fill Valve Problem and Fix: FastTech Forums

I've always filled my 3.1's from the top.
I've read somewhere that the 3.1 fill valve screws up easily if you use to much pressure sticking the needle tip bottle in to hard or too far.
 

Cosmic_Glaze

Super Member
ECF Veteran
Verified Member
Jul 26, 2016
948
3,828
maybe try this...
Kayfun Fill Valve Problem and Fix: FastTech Forums

I've always filled my 3.1's from the top.
I've read somewhere that the 3.1 fill valve screws up easily if you use to much pressure sticking the needle tip bottle in to hard or too far.
Thanks for the tip!....before I read this I found an o ring from a Nautilus coil cut it very small and jammed it into the whole on the deck (inside the tank so it's not visible) it was a temporary fix... it works but not a good idea in the long run..
I will have to try your idea..
 

DavidOck

ECF Guru
Supporting Member
ECF Veteran
Jan 3, 2013
21,239
178,485
Halfway to Paradise, WA
It's leaking from the juice port...where you fill it.. not the air flow hole..there is no screw for it you just push the tip in it and fill..only tried that once kinda made a mess, then I have top filled since.. it's a very slow leak from the seal in it...never had to fill a device like this before... nor have I not had the option of a glass tank to throw any juice in it (menthol)

Gotcha, my miss steak :)

Yah, that's why I top fill my 3.1s, never did like the check valve idea, although I've not had any leaks from them.

As said, first try the thorough cleaning, and maybe "pump" the valve a few times and give it a try (top filling, don't push your luck!) before pulling it all apart and losing pieces :w00t:
 

Users who are viewing this thread