Heres a pretty picture for you. They are still a prototype but theser are some of the panels I am making for the hcigar Vt inbox squonker
Last edited:
Tootle Puffers, Part Three! (The Sequel of the Redux)
- Thread starter Katdarling
- Start date
- th_trl_thread_readers 0
Sorry for all the pictures in this post but I need some help and thought you'd need to see it at all angles. I have chosen highest quality so I'm sure they'll be huge. The STM RBA saga continues. I can't get this to read on the ohm meter. It looks perfectly fine to me. I've tried several bases and it still won't read. It's the stock coil that comes in the kit. However I've tried 316L wire and still couldn't get a reading. I should mention that it worked fine before I pulled out the old coil. I'm totally at a loss as to how to fix this.
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
Sorry for all the pictures in this post but I need some help and thought you'd need to see it at all angles. I have chosen highest quality so I'm sure they'll be huge. The STM RBA saga continues. I can't get this to read on the ohm meter. It looks perfectly fine to me. I've tried several bases and it still won't read. It's the stock coil that comes in the kit. However I've tried 316L wire and still couldn't get a reading. I should mention that it worked fine before I pulled out the old coil. I'm totally at a loss as to how to fix this.
Sent from my iPhone using Tapatalk
try a stock coil to test the base.
I have an ohms meter that hates having anything screwed down tight.
I would check you pin on the base and/or try loosing it off so there is only just contact
I would check you pin on the base and/or try loosing it off so there is only just contact
Thing is, I've tried several bases. Ones that I know work as they're fine with the other RBAs... I've also tried on 2 different ohm meters . Thanks for the suggestion though I'm totally perplexed!
Sent from my iPhone using Tapatalk
I posted on the stm thread but didn't get a response. So maybe this RBA somehow turned "bad" for lack of a better term
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
I had one that was bad from the factory so something may have happened to it.
I guess sometimes vape stuff just goes bad for no apparent reason...? I'm convinced that at least this time, it's not operator error[emoji4]
Sent from my iPhone using Tapatalk
Put a different coil in and try in in the mod first to check if read. And if you have an extra rba deck put that in the reader using the base you are having trouble with.
Heres a pretty picture for you. They are still a prototype but theser are some of the panels I am making for the Hcigar Vt inbox squonker
Man that's Very Very Nice,I love the way the colour flows from dark to light!
I really mean no disrespect, really I don't...
Didja move the switch thingy on the right side to ohm reader?
Other than that, must be the insulator is cracked or allowing arc/contact or the center pin spring is missing or fubar.
I know on all of my cheap ohm checkers if you tighten them too much they don't work or give funky readings.
Just tight enough to prevent wiggle/wobble, yours appear to be a lot tighter than any of mine will work.
And, if you crank down on them even once they rarely work again.
Didja move the switch thingy on the right side to ohm reader?
Other than that, must be the insulator is cracked or allowing arc/contact or the center pin spring is missing or fubar.
I know on all of my cheap ohm checkers if you tighten them too much they don't work or give funky readings.
Just tight enough to prevent wiggle/wobble, yours appear to be a lot tighter than any of mine will work.
And, if you crank down on them even once they rarely work again.
Last edited:
Open up the air control all the way and look into it to see if the bottom of the rba is touching the bottom positive pin in the base...maybe use a flashlight. Could be no connection of the two.
Similar threads
- Locked
