Top air RTAs
- Thread starter Shawn Hoefer
- Start date
- th_trl_thread_readers 0
- Status
No worries @Daniel Forsyth, these things happen.
I only bought old school analogue for the simple reason that there's less to go wrong.
I only bought old school analogue for the simple reason that there's less to go wrong.
Thanks!@Jumpin' In... , you forced me to use my Vernier Calipers!
1.6mm is the diameter of the airflow under the coil.
A tad too tight for me, I’m afraid. Same as my YFTK 24mm kayfun Lite 2019 I think.
Maybe even a little more @Jumpin' In..., genuine is 1.8mm max. PM me if you wish, I may have an idea for you.
@Daniel Forsyth, you'd need more than that. The centre screw with airhole would have to be completely replaced.
It could be done though.
It could be done though.
Hey Shawn, I can't seem to find the review for the Exvape Expromizer V4. When I click on the link it sends me to one of the Solomons.
Here you go @Vapemesilly, the link for page 30 where the Exvape Expromizer V4 is reviewed.
Top air RTAs
It's near the bottom of the page.
@Shawn Hoefer, could you fix this please. Thank you.
Top air RTAs
It's near the bottom of the page.
@Shawn Hoefer, could you fix this please. Thank you.
It's too late... I cannot edit that post...
Anybody know where to get the replacement bubble glass for the OG zeus (single coil)?
Try these two from FT:
AOLVAPE Replacement Glass Tank for GeekVape Zeus RTA Atomizer (2-Pack)
Rainbow tanks that also fit the original Zeus RTA:
Authentic Vapesoon Glass Tank for Uwell Nunchaku Tank Clearomizer (2-Pack)
thanks AngeNZTry these two from FT:
AOLVAPE Replacement Glass Tank for GeekVape Zeus RTA Atomizer (2-Pack)
Rainbow tanks that also fit the original Zeus RTA:
Authentic Vapesoon Glass Tank for Uwell Nunchaku Tank Clearomizer (2-Pack)
I see some people here used Serpent Elevate. Did someone try the clone? I don't remember where did I get it, but it is my everyday now and I'm trying to find a proper glass tank. Got one from fasttech a week ago - but it does not fit, too narrow.
Any suggestions much appreciated
Any suggestions much appreciated
Thanks, Shawn for all your hard work and in depth research... 
After much contemplation I decided to get the Zeus X. Hope I made a wise decision. I’m not the best by any means at wrapping coils and building/wicking but I’m going to give it my best trying to mount a single SS coil onto the deck. Hopefully SC builds suck through juice slower and drain 18650 batteries slower?! I’m attempting a 4mm ID, 5 wrap coil with 22G 430 SS. Target resistance is between 0.15-0.2 ohm. I bought this nickel free 430 from unkamen supplies back in 2015 or 2016. Only tried once cause the RTAs back then just not enough room for it and I always forget I have all these TC wires!
Maybe next time I’ll go for a 4.5mm SC build! Would that even fit?! 4.5mm is the largest coil jig rod I have in my 6 piece set from Fasttech. 4mm should be interesting though as it’s my largest coil in terms of diameter I’ve tried... wick it with Graham Rayon and hopefully be good.
After much contemplation I decided to get the Zeus X. Hope I made a wise decision. I’m not the best by any means at wrapping coils and building/wicking but I’m going to give it my best trying to mount a single SS coil onto the deck. Hopefully SC builds suck through juice slower and drain 18650 batteries slower?! I’m attempting a 4mm ID, 5 wrap coil with 22G 430 SS. Target resistance is between 0.15-0.2 ohm. I bought this nickel free 430 from unkamen supplies back in 2015 or 2016. Only tried once cause the RTAs back then just not enough room for it and I always forget I have all these TC wires!
Maybe next time I’ll go for a 4.5mm SC build! Would that even fit?! 4.5mm is the largest coil jig rod I have in my 6 piece set from Fasttech. 4mm should be interesting though as it’s my largest coil in terms of diameter I’ve tried... wick it with Graham Rayon and hopefully be good.
I just posted a question for you here on the ft forums. Maybe someone will have answer.
Serpent Elevate Styled RTA Rebuildable Tank Atomizer
- Status
Similar threads
