VA Variable Volt Mod Version 1.5

[muldrick]

This is the Version 1.5 which allows you to check the resistance of your atomizer with a simple push of a button. • Install the battery positive end first (has reverse protection) • Press the power button 5 times to turn the unit on. • Adjust your preferred voltage with the + and – buttons • To check atomizer resistance press the power button one time • To turn the unit off (pocket friendly) press the power button 5 times 2 Buttons allow you to select voltage from 3 volts to 6 volts, in 0.1v increments. Regulated output keeps the voltage the same regardless of the remaining battery power. As the battery drains, the device will keep the voltage consistent. 10 Second Cutoff timer: If the activation button is held down for 10 seconds or longer, the unit will shut itself off until the button is released to prevent overheating the atomizer and the device. Short Circuit/Atomizer Protection: The VA Tube Mod can recognize an atomizer with a resistance too low for the current voltage setting and will drop the voltage to 3.7v to protect both the battery and atomizer. If the atomizer is too low or shorted out power will be shut off to protect the VA Tube Mod from being damaged. Reverse Battery Protection protects the device in case you put the battery is installed backwards. Battery Monitoring/Over-Discharge Protection: The device will monitor the battery voltage and automatically turn off when the battery is discharged, preventing damage to the battery by overly depleting it. The VV Tube Mod includes a voltage meter in the LCD display, simply press the red power button 6 times and it will display the voltage of the battery for a few seconds allowing you to monitor the power left in the battery before it needs to be recharged. The 2 included 18650 High Drain batteries provide 4.2V at peak charge that will decrease to about 3.3 volts with use, before needing to be recharged. This will help you monitor the life cycle of the battery. The LCD screen will flash when the battery needs to be recharged, and will stop powering the device. Vent hole on the bottom of the device for added safety. Dimensions: 5"L x 0.86"D 1 x VA Variable Voltage Tube Mod - Body Unit 2 x High Drain 18650 Battery 1 x 18650 Battery Charger 1 x Gift Box This kit does not include atomizers.

 

[Snus]

Sounds really nice..... I'd love to get a vv!

 

[xwickedx]

I have one of these being shipped can't wait to start vaping. It's my first PV. I think from the looks of ricks fast shipping from other customers i should probably get it tomorrow. Thanks Rick was surprized to see my order status saying Shipped couple hours after ordering on friday night.

 

[muldrick]

Thanks WickedX,
You definately picked a good device. Most folks start with junk, and unfortunately give up because the (cheaper) device did not perform well.
I think you'll be fine as this VV Mod is great. Keep us posted on your progress.

Please note though, that went out Saturday morning, so I think you'll have it Tuesday or Wednesday.
Let me know.
--
Rick M

 

[xwickedx]

I was wondering if this LT has the higher amp rating then the ones with 2.5 i seen other 1.5 versions with the new resistance display say they are rated at 3 or 3.2 amps. Do you know what this is rated at?

 

[muldrick]

I am told they are the 3 amp.
I just got the Lambo's in and I want to do some testing with a multimeter to verify this on all versions.
However, being a little busy this may be a while before I get this done.

 

[muldrick]

The V1.0 has the 2.5 A circuit.
The V1.5 has the 3.2 A circuit.
The Lambo has the 2.5 A circuit.

 

[jteezy]

Rick do you think the VA Variable Volt Mod Version 1.5 will be available in a mini version in the near future? Thanks

 

[muldrick]

Yes, in fact I plan to order them tomorrow.