Valley View Vapes - **Official Information and Chit Chat Thread**
- Thread starter RayN
- Start date
- th_trl_thread_readers 0
- Status
Nice. Now we need pics with that new fancy lens of yours Og
tapped not typed
tapped not typed
Congrsts ogfish!!
Okay, my night is done... I got LOTS DONE! Now I am vaping some old DV Toffee Sugar Cookie... been steeping for 2 months... smells DELICIOUS... but I taste nothing and the 18mg nic burns bad... At 6w I start to taste *something* then my nose starts burning like a mufo and I have to stop... oh well, going to cut the nic by mixing this toffee sugar cookie into some tiramisu...
Okay, my night is done... I got LOTS DONE! Now I am vaping some old DV Toffee Sugar Cookie... been steeping for 2 months... smells DELICIOUS... but I taste nothing and the 18mg nic burns bad... At 6w I start to taste *something* then my nose starts burning like a mufo and I have to stop... oh well, going to cut the nic by mixing this toffee sugar cookie into some tiramisu...
Last edited:
That's a nice tank, I'm diggin' the gold! Gold tip from Ray too?
@ Ray, if you see this and you have a sec, could you tell us what order # you're currently working on?
Thanks much!
@ Ray, if you see this and you have a sec, could you tell us what order # you're currently working on?
Thanks much!
No, I got that tip from somewhere else, but it matches the cap great.
Read back a bit, and saw you all are working on hitting lucky number 2000, so -- HI
! Just got a co-worker off of analogs my giving her one of my Valley View tanks...
on being the key to my 4th convert!!
! Just got a co-worker off of analogs my giving her one of my Valley View tanks... on being the key to my 4th convert!!
Ok, troubleshooting question! My 3ml capped polypro is leaking from the bottom cap, where the cap meets the polypro tube.... It was real bad at first, but has slowed down now. Once my juice level gets lower I may try a different tube. When I unscrew the screw to release pressure it leaks again. Bad seal? Bad o ring? Suggestions? I do think in the cleaning process the caps wound up on an older and more well used tube, but its still in good shape. Thanks!
I've honestly never had that issue before. I've been using the same tank with the same grommet and o-ring for 8 mos now trying to see how long it will last.
Did you rinse it off and dry it before you re-assembled it?
Did you rinse it off and dry it before you re-assembled it?
Yeah to be honest with ya I'm more interested in the physics of what's happening than annoyed at it LOL it doesn't logically make sense to me for the leak to be where it is. It was rinsed super well and dried overnight, I don't do "full cleans" like that unless I switch flavors, which I was, generally if I'm just swapping cartos I'll leave it be. What gets me is because I am having to release pressure I'm quite sure I've got a good seal. I'll play with it and figure it out and report back. Not gonna lie, when the juice ran low I refilled it instead on swapping the tube, just so I can further observe. The leak now is minimal. I'm thinking the issue is the tube, not that its bad but that I think this tube is from one of my grommet tanks, hence I think there may be the slightest bit of wear on it from reworking the grommets, hence its having a harder time creating the seal with caps, and a now minimal amount of juice is working its way under the o ring and hence escaping where the cap meets the polypro. I find the tube "loose" as well in that I can easily spin it without moving the caps at all, usually it takes some minor effort to spin the tube on a sealed tank. Once I change the tube I will let ya know if it corrects the issue LOL. Leave it to me to find that wierd random issue lol. Too bad I don't have that luck with the lottery lol
lol
Also, as far as longevity, I've not had a tank I got from you die yet. They've been thru hell too lol. I'm nice to my pyrex, but not my polypros those take the full brunt of my day to day lol. I really think this is cuz I mixed up which tube is which.
Hey DreamingButterfly81, you have some citrus juice in there? I made some lemonades [strawberry, peach, & blueberry] that were DELICIOUS, but they leaked out of EVERYTHING! I finally had to mix them with more PG and combine 'thicker' juice.
As far as the grommets or o-rings getting out of shape, I boil water and soak them in it [with the tank, clearo, whatever] and then let them dry. I have made a punch in the wrong place previously and it affected my grommet shape... after the hot water bath and drying it was fine!
As far as the grommets or o-rings getting out of shape, I boil water and soak them in it [with the tank, clearo, whatever] and then let them dry. I have made a punch in the wrong place previously and it affected my grommet shape... after the hot water bath and drying it was fine!
Oh no wuts this?? Some VVVape mail!!!!!!!!!!
Jumbo 8ml tank
And the whole VVV Family
Jumbo 8ml tank
And the whole VVV Family
JR I also prefer the screw on the bottom!
(that's what she said)
Why's your 7ml crooked!!!
(that's what she said)
Why's your 7ml crooked!!!
Can ya tell me why you like the (THUMB) screw on the bottom?!?!!! I'm new at this tank stuff! Thanks!!
Was not screwed down all the way.
Can ya tell me why you like the (THUMB) screw on the bottom?!?!!! I'm new at this tank stuff! Thanks!!
I do it so I can fill it upside down so I don't flood the carto.
Sent from my NS4G powered by Helly Bean
- Status
Similar threads
- Locked
- Locked
