yep,
but no screws to the case on mine
It has no 4 screws that hold the top plate on?
Vapor Flask V3 DNA40 Clone thread
- Thread starter Croak
- Start date
- th_trl_thread_readers 0
- Status
It has no 4 screws that hold the top plate on?
well, I'm sorry forgot to tell you my mod is a Hana box clone,
but I meant somebody may have clone board's wiring photo or scheme
Last edited:
Basically same deal as flask except ground is through the 510 outer shell into the case because of the "press fit" 510. Wiring diagram for a DNA 30 type board, if you need more do a search for DNA 30 schematic.
Same as the authentic. While locked, hold down the fire and down buttons simultaneously for 5 seconds.
I was contemplating the same thing after just seeing it. Want a dual battery setup as well, but price point is nice. With thoughts of "well, i could always grab that instead of the SX Mini for a leave the house setup when it's raining"
Here:
If it doesn't ground this way perhaps the ground wire is attached directly to the 510's negative.
Last edited:
Here:
If it doesn't ground this way perhaps the ground wire is attached directly to the 510's negative.
so that explains why I dont see any attachment to the body,
thank you @dwcraig1, gonna check the 510 connections and it's solderings
My Kangxin flask has entered the country! If I'm lucky I'll get it tomorrow, but in all likelihood the postal service will take its sweet time and I'll have to wait until next week :-( Extra annoying as I can pretty much walk to the foreign postal arrivals center but am not allowed to collect my package there...
Seems like Waidea copied the real Vaporflask too well, and they copied the first run of the DNA40 2.1 model that sometimes had grounding issues.
Mine started showing "weak battery" with two 85% charged batteries. Didn't matter what tube the batteries were in, if the charge was not real close to full on a battery, it wouldn't work.
It's a ground issue on the 510 (and probably related to what TheBloke was running into). There's no solder used to ground to the 510, just a bare cable (actually stranded like a cable instead of a traditional stranded wire) that is trapped between the top plate and the brass nut threaded onto the 510. While it's a clean install and pretty abuse resistant, especially during assembly, it's not an ideal ground as it is.
Tightened the nut and the problem seems to have went away for now. Will probably end up breaking out the soldering iron and insuring a better connection.
On a positive note (see what I did there?) it looks like it should be fairly easy to install the 510 of your choice in there, tons of room top to bottom, unlike the Kangxin flask.
Mine started showing "weak battery" with two 85% charged batteries. Didn't matter what tube the batteries were in, if the charge was not real close to full on a battery, it wouldn't work.
It's a ground issue on the 510 (and probably related to what TheBloke was running into). There's no solder used to ground to the 510, just a bare cable (actually stranded like a cable instead of a traditional stranded wire) that is trapped between the top plate and the brass nut threaded onto the 510. While it's a clean install and pretty abuse resistant, especially during assembly, it's not an ideal ground as it is.
Tightened the nut and the problem seems to have went away for now. Will probably end up breaking out the soldering iron and insuring a better connection.
On a positive note (see what I did there?) it looks like it should be fairly easy to install the 510 of your choice in there, tons of room top to bottom, unlike the Kangxin flask.
You can switch the LED on and off and into a very usefull strobe mode LOL. First I didn`t like the LED, but I think it can be useful - work on your atty f.e.. I hope it will get a lens or sth to seal the hole - don`t want to flood the board.
Doris is everywhere, now she is on YT
Edit: FC has the big Flask in the promotion for 59$
Last edited:
I'm just going to leave this here... Taifun gt with taifun gt2 base and a black pmma tank. Excellent vape.
It's the kangxin one for $59
http://focalecig.com/Product/VF-V3-StyleTemperature-Control-40W-Clone-Mod-by-KangxinBlack-24163
Edit: thank you nailz.
Wow that video! The cheese!
I like the device even more now though, green still looks awesome! And it has sprung 510 pin!
In other news: Chinese bloke is contemplative about his vape.
Perhaps he's reflecting on Kangxin's many astonishing achievements: who knew they had the first ever 40W device, the first 50W 'variable' device, and the first ever 40W temp control device?! And all since October 2014! Ah, they must be using a rather narrow definition of 'in this industry' (Shenzen downtown area?)
I like the device even more now though, green still looks awesome! And it has sprung 510 pin!
In other news: Chinese bloke is contemplative about his vape.
Perhaps he's reflecting on Kangxin's many astonishing achievements: who knew they had the first ever 40W device, the first 50W 'variable' device, and the first ever 40W temp control device?! And all since October 2014! Ah, they must be using a rather narrow definition of 'in this industry' (Shenzen downtown area?)
Last edited:
I saw this on another thread... Nearly spit coffee on the keyboard from laughing
Thanks for the condolences Tpat
. I am sure FT will take care of the issue. I have ordered lots from them and on 2 occasions have had to warranty products. It's very easy. Just get a shipping quote to Florida then they approve it and give you the RMA number. Once shipped I take a photo of the receipt and they credit you within a day for the shipping. About a week later when it's received they either ship out the replacement or credit your account. Takes longer then dealing with a local B&M but I only buy stuff from them I can't get locally. I usually pay the higher markup to support my local shop and the convenience. I just moved so I have no loyalty to the one in my new town but will probably keep that policy going as they seem very good and have reasonable prices.
At the end of the day if I am going to order from China it will most likely be from FT based on decent customer service (for what and where it is) and not a worry about needing warranty support. Again it takes time but will not leave you with a lemon just a bit of a wait...which should be expected dealing with China and only paying 2.50 for epacket.
It will be interesting if they can actually replace the Flask with them all being removed from their site. Does anybody remember if they had the Waidea/Sunlay before they were taken down? I will keep you all posted.
anyone else heard the rumor that weadai, or however you spell it... is going to update their flask to a spring loaded pin? I saw a review and, the reviewer said they told him that they where. I also read it somewhere 
is going to update their flask to a spring loaded pin? I saw a review and, the reviewer said they told him that they where. I also read it somewhere - Status
Similar threads
