Wismec Reuleaux RX 200 Firmware 3.0 - Just Released
- Thread starter niczgreat
- Start date
- th_trl_thread_readers 0
- Status
120 420'F at 60 Watts Still get temperature control warning. and little vape.
I was pleasantly surprised with this update. I was expecting tc to be confusing but my first build with 304 stainless using a tcr of 0104 and it's regulating perfectly with dual contact coils 
Running it at 140 watts and 530f no dry hits whatsoever. I see what all the fuss is about now. Kudos to joyetech for sticking to their word
Sent from my LIFE PURE using Tapatalk
Running it at 140 watts and 530f no dry hits whatsoever. I see what all the fuss is about now. Kudos to joyetech for sticking to their word Sent from my LIFE PURE using Tapatalk
Wierd. Try a new coil. I have 4 crown tanks with .25 coils installed and they all work great in TC mode.
The atty is at least 3 weeks old, so I'll try again with a new one when this one finally gives out.
Updated this morning, set M1 to 0105 for 304 stainless, 75W @ 520 degree and it was doing great. This evening, it won't stay in TC. It keeps jumping to wattage mode @ 20W. Change it back to TC and as soon as I hit the fire button, it's back to wattage @ 20W. Pulled the batteries, set it to TC, hit the fire button and back to wattage @ 20W. Any ideas? Parallel 26 ga. 304 stainless, dual coils.
If you all didn't see the thread check/ask over there too. I know there are over 100 pages but many of us ordered them on release. I have not updated mine yet to 3.0 but the last few pages it has been being discussed. I use ni wire so no help on ss.
WISMEC Reuleaux RX200 TC
WISMEC Reuleaux RX200 TC
Got it sorted. It was actually my atty. The Subzero has that standoff deck and the bottom piece was getting loose, so contact with the 510 was intermittent. Tightened it up and all is well.
You're not the only one Tom. More details in the comments.
Issac Gutierrez Correct the TCR mode isn't working like it should
Like · Reply · 1 · 5 hrs
Mike Vapes Yeah I tried 316 on tcr at 92 and on the ss preset and it temp protects right away.
I'll have to just stop using either the default, or even the mem reg I set up to duplicate it with my 0.5 Crown head and just use Power Mode because... "the ss functions will not work in the new tcr mode and in ss mode for temperature control".
Well damn.
It's the reverse, and just as bad, as those who told us we weren't really having TC issues with our VTCs.
Are there issues? Sure. I have no idea why JTech's TCR calcs seem to be all over the place.
Four mods from three divisions and I'm not seeing a ton of consistency in the TC issues.
But let's try to keep a leash on the hyperbole.
Well damn.
It's the reverse, and just as bad, as those who told us we weren't really having TC issues with our VTCs.
Are there issues? Sure. I have no idea why JTech's TCR calcs seem to be all over the place.
Four mods from three divisions and I'm not seeing a ton of consistency in the TC issues.
But let's try to keep a leash on the hyperbole.
You have to play with the TCR setting to get it right for my lemo v1 I use 0172 for 430 ss with the subtank plus I have to use 0220 to get the same vape. This won't be the last firmware release for the rolo and this update does allow you to dial in for the vape you want so this whole "do not do the ver 3 update" is drama queening at it's worst. As a rough rule of thumb take the TCR for your wire and add 34 as I did on the lemo 1 430 ss TCR is 0138 on the rolo and some tanks\builds may require a higher compensation but tc still works even with the compensate. Add in you can do the update and if you don't get on with it you can reflash another version because the update procedure for the rolo is as easy as it gets. Least I now know one YouTube reviewer not to bother with.
I don't see the drama queening here, I just see somebody giving a heads-up to people (and offering up solutions along with others in the commentary). And he's right, SS temp control doesn't work properly with the 3.0 update.
Telling people not to update is drama queening there is nothing dangerous or even difficult about ver 3 you just have to work a tiny bit harder to dial it in and it is a tiny bit of work and the upgrade works so what reason is there not to update to it??.
Croak, I have no explanation for the TCR value discrepancies. I have a mem slot jacked up to 125 to match the SS mode. That's "too damn high", but it works.
Just swapped the potentially dodgy 0.5 Crown for a dual 26g (316L) at 0.18 in a V Mini.
Both running 45w/440F.
Much the same... and the standard SS mode is not anemic. Go figure.
Just swapped the potentially dodgy 0.5 Crown for a dual 26g (316L) at 0.18 in a V Mini.
Both running 45w/440F.
Much the same... and the standard SS mode is not anemic. Go figure.
430ss tcr@130 the rest is on the screen. Vaped 20ml of juice in the last 2 days. Never once kicked out of TC..
Because people updating are not expecting problems, they're expecting improvements. Not everyone follows forums or geeks out as much as some of us here do, and not everyone is willing to put up with "workarounds", and some don't even know what a TCR is, they just use the preset SS mode and expect it to work. For those people, it's good advice to tell them something is not right with the update, and to hold up or roll back. It's also good information for those that have updated and then think they're having build problems when its the mod, like oh, @tomzgreat , the OP of this thread.
@BoostAddict it's not a problem with 3.0 kicking you out of TC, it's a problem with the mod thinking SS is vaping hotter than it really is, and throttling back power too early, in some cases almost as soon as you fire, resulting in a very weak vape, and it's more problematic with 316 and 317 that have lower TCR than 430 to start with.
At TCR 130 I got wisps of vaper on the lemo v1 and nothing on the subtank plus the tc seems very erratic but at least with the latest update we're all able to alter what we need to get the vape we want, though I can't explain the variances.
Well if people are as you say Croak why is mike vapes saying don't update as the people you mention won't be watching him either. Ver 3 isn't perfect not seen anyone say it is but with a bit of work it does work I still do not understand anyone being told not to update.
Hate to break it to you, but there's almost certainly an order of magnitude more vapers casually following vaping news and reviewers on Facebook, Instagram and Twitter than there are hardcore types like us on a low-traffic specialty subforum on ECF.
Your not breaking anything to me ECF in fact add all the vaping forums together and it's a miniscule amount of the total vapers and anyone who see's the problem on Facebook, Google+, Instagram or any other social media will also find the solution quite quick I know I did . I've still not heard a compelling reason why anyone should not update to ver 3 because those looking to do it likely will do it for the user adjustable TCR that is the biggest aspect of ver 3 having to tweak the TCR value to get your vape where you want it isn't rocket science and there's already a lot of stuff across social media showing and explaining the ver 3 update. Only one person is telling people not to update speaks for itself really.
. I've still not heard a compelling reason why anyone should not update to ver 3 because those looking to do it likely will do it for the user adjustable TCR that is the biggest aspect of ver 3 having to tweak the TCR value to get your vape where you want it isn't rocket science and there's already a lot of stuff across social media showing and explaining the ver 3 update. Only one person is telling people not to update speaks for itself really.- Status
Similar threads
