Wizard/ Vrajitorul Smallest and lightest mod ever made

[jcy0001]

becasue its titanium?

I'm assuming that since it titanium it should weigh less than the ss one n bassed on the weight of the original wizard with an 18650 bat still being a few grams lite of of the 18350 ss then again my assumptions could be wrong hihihi I've never really owned anything titanium so preaty excited hope I get one from the earlier parts of the forum it seems really difficult to get one

 

[ukeman]

Wizard Ti is rare indeed, and very light... going by the Wand Ti's machining, and perfectly detailed.
Reviewer Todd says its light as a feather ...
I did see a couple in the classies a few weeks ago.. and never since... one set (Wizard Ti and Wand Ti) was sold for less than retail and was snapped up in 10 seconds... dang

I'm assuming that since it titanium it should weigh less than the ss one n bassed on the weight of the original wizard with an 18650 bat still being a few grams lite of of the 18350 ss then again my assumptions could be wrong hihihi I've never really owned anything titanium so preaty excited hope I get one from the earlier parts of the forum it seems really difficult to get one

 

[ukeman]

ooh I finally took my Wand Ti apart to change out the stock plastic (not sure what kind) tank cylinder which was cracked from Pluid use.
I have a couple 20mm glass cylinders cut to fit... but... apparently the Wand Ti tank protector is 20mm (approx)... so it won't fit, and tubes apparently need to be a tad under 20mm (19.98mm) to fit the Wand.

Mark, is there any way to purchase replacement tanks for the Wand Ti ?

 

[mark78]

ooh I finally took my Wand Ti apart to change out the stock plastic (not sure what kind) tank cylinder which was cracked from Pluid use.
I have a couple 20mm glass cylinders cut to fit... but... apparently the Wand Ti tank protector is 20mm (approx)... so it won't fit, and tubes apparently need to be a tad under 20mm (19.98mm) to fit the Wand.

Mark, is there any way to purchase replacement tanks for the Wand Ti ?

Send me an email mark@markbugs.com with your adress.

 

[Paul66]

So today I got 2 glass windows.
Both of them didn't fit.
As ukeman already mentioned pluid + wand window = cracks, I tried to find a solution to use my glass windows.
If you don't use the Wand sleeve, it is possible to hold the glass window between the two rubber o-rings.
Since my topcap is on the way from Mark to me, I can not tell you if it is a stable solution.

Better would be glass windows with a diameter slightly less then the Wand sleeve inner diameter.

 

[ukeman]

wow I didn't think of fitting the glass like that Paul.... hmmm.
i do have my top cap, so maybe i'll try it.... later.

So today I got 2 glass windows.
Both of them didn't fit.
As ukeman already mentioned pluid + wand window = cracks, I tried to find a solution to use my glass windows.
If you don't use the Wand sleeve, it is possible to hold the glass window between the two rubber o-rings.
Since my topcap is on the way from Mark to me, I can not tell you if it is a stable solution.

Better would be glass windows with a diameter slightly less then the Wand sleeve inner diameter.

 

[jcy0001]

Any news on the new wizard? Is there another forum where they update? Just checking

 

[mark78]

Any news on the new wizard? Is there another forum where they update? Just checking

Looks like at the end of next week we will have them ready, we will anounce here with 24-48 hours before we will start put them on stock.

 

[ukeman]

hmm. Cld9uk or mb.com site?
very exciting... any clues on which products, any new concepts, on what is forthcoming?

Looks like at the end of next week we will have them ready, we will anounce here with 24-48 hours before we will start put them on stock.

 

[jcy0001]

Nice whew thought I missed it

 

[mark78]

Hi everyone,

Wizard is in production right now and will have few different features then the previous series:

- it is made from titanium implant grade
- the electronics inside will work if you insert the batt with the + up and can be used with the kick
- the engraving will not be made with the laser, will be mechanical
- the bottom of the tube will be changed not as the design ... just for a better functionality.
And will be made for the 18650/18500/18350 batts like his Apprentice.

That is for the now the pics will follow as soon as the Wizard is done.

It will be for sale in May.

Thank you,

And yes c9v and mb site

 

[ukeman]

super! looking forward to the info

Looks like at the end of next week we will have them ready, we will anounce here with 24-48 hours before we will start put them on stock.

 

[StevesCVO]

All you modders are killing me with stuff I think I need

 

[vaptamist]

A wizard for a 350 battery would be incredibly small and light! I'd estimate 26 to 27 grams. That's almost nothing!

 

[ukeman]

I'd love to have a chance at an Infinity and a Chalice from Mark...

 

[pmar4015]

Would love to get my hands on an 18350 Wizard's Apprentice. Anybody have any idea how to go about such?

Also, does anyone know when Mark Bugs will have the 18350 available again?

 

[mark78]

Would love to get my hands on an 18350 Wizard's Apprentice. Anybody have any idea how to go about such?

Also, does anyone know when Mark Bugs will have the 18350 available again?

In May you can get only 18350 Wizard and probably in october or november the Wizard's Apprentice.

 

[mark78]

And, as we promised, there are some photos with the Wizard:

One comment ... it is easier to make them then to make pictures of them!!!

 

[toolguy420]

Unbelievable work...VERY NICE!!! <cleans drool off chin> What day can I put one in my shopping cart?

 

[vaptamist]

Beautiful! Definitely like the machine engraving.