- Status
Hi everyone! Hope you all had a pleasant weekend! I did! There's was eating drinking and merriment! As always!
Now, the weekend has come to an end and it's time for my usual routine...I beer, some vaping, and my clay facial mask so my complexion stays smooth and blemish free. Hope you all enjoyed yourselves.
I'd smile, but I can't since my mask is drying and my face can't move.
Now, the weekend has come to an end and it's time for my usual routine...I beer, some vaping, and my clay facial mask so my complexion stays smooth and blemish free. Hope you all enjoyed yourselves.
I'd smile, but I can't since my mask is drying and my face can't move.
OH!!! I'd thought you were putting on the first layer of a life-cast so you can start doing your Halloween appliances early!
Hope you put Vaseline on your mustache and eyebrows....
-Insp. 2211
OH!!! I'd thought you were putting on the first layer of a life-cast so you can start doing your Halloween appliances early!
Hope you put Vaseline on your mustache and eyebrows....
-Insp. 2211
Vaseline is on, but not on my face.
Ouch... in more ways than one.
(About 1/2 of my eyebrows - and 1/4 of my beard - is imbedded in concrete of this first cast I did a few years ago, before I got good at... lubing up.
)
-Insp. 2211
Grr. PV is driving me crazy.
Ever have condensation build up in your cap, or have your wick overwick, and get liquid blocking the air hole in the cap a bit? How that draw is a lot tighter and there's little vapor?
I just cleaned up my drip tip and PV and am getting that type of hit right now. Cleaned out the hole in the top cap to not much avail.. Switched out drip tips and it's perfect again. I don't know what's going on with the Stylus tip I have.. It seemed to become a problem after cleaning it. I guess I'll clean it out again.. but I'm not seeing anything that could be an immediate problem.
How did everyones memorial day go?
My father will be back in Michigan for the first time in 7 months, so I'll get to see him in the morning!
Ever have condensation build up in your cap, or have your wick overwick, and get liquid blocking the air hole in the cap a bit? How that draw is a lot tighter and there's little vapor?
I just cleaned up my drip tip and PV and am getting that type of hit right now. Cleaned out the hole in the top cap to not much avail.. Switched out drip tips and it's perfect again. I don't know what's going on with the Stylus tip I have.. It seemed to become a problem after cleaning it. I guess I'll clean it out again.. but I'm not seeing anything that could be an immediate problem.
How did everyones memorial day go?
My father will be back in Michigan for the first time in 7 months, so I'll get to see him in the morning!
Grr. PV is driving me crazy.
Ever have condensation build up in your cap, or have your wick overwick, and get liquid blocking the air hole in the cap a bit? How that draw is a lot tighter and there's little vapor?
I just cleaned up my drip tip and PV and am getting that type of hit right now. Cleaned out the hole in the top cap to not much avail.. Switched out drip tips and it's perfect again. I don't know what's going on with the Stylus tip I have.. It seemed to become a problem after cleaning it. I guess I'll clean it out again.. but I'm not seeing anything that could be an immediate problem.
How did everyones memorial day go?
My father will be back in Michigan for the first time in 7 months, so I'll get to see him in the morning!
The tip is too long, when fully pushed in the bottom of the tip is most likely touching the top of the positive post. Either lift it out a touch, or sand away th bottom of it.
Huh. Lifted it up a tad and it's performing immediately better. I must have damaged part of the o-ring on the tip when cleaning it or something. *shrug*
Thanks, Ian.
Good evening everyone!
And ya do the hokey pokey and ya turn your self around!! Anything that requires that much work to fill is not for me!
And ya do the hokey pokey and ya turn your self around!! Anything that requires that much work to fill is not for me!
Stevo is back...or catching up from the UK. Either way, hope you're well bro
Not sure what you mean? Work? Lol, it's not hard to cover a hole while you unscrew the topcap and fill with your bottle..I'm confused why this is hard? Also once ya get the proper fill bottles ya don't even need to take the cap off..
What a crappy weekend, I sure hope you all have great weather for vapestock in FL -- speaking of, where's the lovely readmermaid been?
OK. I'm contemplating the future of vaping tonight. you know how they want to ban infernet sales? well what if you only used the internet to browse the "catalogs" of vaping vendors? Then you had to call to actually place an order. That would get everyone around the Technicality right?
The way i read it it seams more like ya gotta cover the hole, unscrew cap slightly turn, fill, tighten up more flip, watch bubble....... Not trying to cause issues dude, just the way i read it.
- Status
Similar threads
- Locked
