I just opened it to look at it. At first it was hard to hit then I got lots of vapor all of the sudden. It kind of worried me from what I've read so far. I opened it to check it out. Not tilted and no leaks. I guess I just got lucky? Will check back later when I can attempt to refill. Working great so far!
ZFM Zero Filler Mod
- Thread starter SCOTTYBALLS
- Start date
- th_trl_thread_readers 0
- Status
use RVT to hold it in place i use a pin hole and i have not flooded my atty. i tryed this frist on my most leaky atty. on a side note if the cig is not up right and the cart gets low you wont wick 
use RVT to hold it in place i use a pin hole and i have not flooded my atty. i tryed this frist on my most leaky atty. on a side note if the cig is not up right and the cart gets low you wont wick
That makes sense.
It's not too likely people look up to take a hit.
When I opened mine I could see the atty made it cone shaped.
Maybe if I flip it upside down with a shorter straw, since it is already cone shaped, It would be like an automatic drip?
Just a tip im going to throw out there if anyone is having a problum it might not be the cart you made take a look at your attys bridge.. I have had some pushed to the right, left, curved and not pointed... Look closely before putting your cart on the atty dose it look like the tip of the bridge is going to line of with the hole? if not you can lightly push on the atty to get it in the center..
Try 2 layers double it up and it might be good btw.. if you plug is not staying in you need to make the plug just a tad bigger there is no need to add silicone to hold it in..
Here you go for those wondering if the stuff will melt I just burnt up another cart thats 2 in 2 days!! I sat down and was eating dinner felt my leg burning @#$% I forgot to turn the barleby off again!! Melted the rim of the cart but the plug is still good!
here is another tip if your setting your ecig down for a bit take the cart out. on mine the cart dose not leak at all but if left in then the hole is open and will leak and flood the atty.
this just happened to me but it was on a test so i took the atty off and set it up right and there was a puddle under it.
this just happened to me but it was on a test so i took the atty off and set it up right and there was a puddle under it.
I just used the metal tip of a click pen to punch a little hole. I just took out the ink tube, reassembled, then pushed down onto the silicone, wiggled it about a bit, and had a perfect 1mm hole. It worked great!
The pinhole was too small. The X was just a pain to make. This seems to be working just right!
The pinhole was too small. The X was just a pain to make. This seems to be working just right!
I don't know about the hole (small hole-punch?) but I have an idea for the X or + cuts:
If you can find the right size Phillips screwdriver, put the point on the silicone and tap it through by hitting the end with a small hammer or something. The hardness of the work surface would also be important...
It is working great still. I did however have to take off the cap to refill. But it was easy.
Best working mod EVER!
Holey (Holy?) Silicone, Batman!
This is the best!
1ml gone in minutes!
You could always use the safety pin in the corner of the plug and lift for air flow when filling.
Holey (Holy?) Silicone, Batman!
This is the best!
1ml gone in minutes!
You could always use the safety pin in the corner of the plug and lift for air flow when filling.
Another fine example of logical thinking. And here I thought my days of cutting straws was over for good! Unlike the ADM this may take a little more tweaking--welcome to my world--to get the bugs out.
I won't have time to test it until tomorrow night, but what is the best way to cut a hole? When I want a tiny hole in plastic I use a heated paper clip but that won't work here. Maybe punching out a hole with a needle? With a little needle you could punch out a dotted pattern. A bigger needle? I've got plenty of little drill bits so that's probably the direct I'd go in for now.
Removing and refilling? Paper clip should would nicely to put in the hole and pop it out. Kind of like taking the cap off a cartomizer.
Good point about centered the atomizer wick.
Yeah, this is the kind of xxxxx right here that keeps me up at night. For a change I'll let you guys play with it a little longer before I jump into the fray.
--Prof Daffy
P.S. Great another thread to keep track of!
I won't have time to test it until tomorrow night, but what is the best way to cut a hole? When I want a tiny hole in plastic I use a heated paper clip but that won't work here. Maybe punching out a hole with a needle? With a little needle you could punch out a dotted pattern. A bigger needle? I've got plenty of little drill bits so that's probably the direct I'd go in for now.
Removing and refilling? Paper clip should would nicely to put in the hole and pop it out. Kind of like taking the cap off a cartomizer.
Good point about centered the atomizer wick.
Yeah, this is the kind of xxxxx right here that keeps me up at night. For a change I'll let you guys play with it a little longer before I jump into the fray.
--Prof Daffy
P.S. Great another thread to keep track of!
Last edited:
I used a pen like madeyetony but all I have is some with plastic tips they still work but I only got 2 done before I destroying my pens tip, then I used the needle that came with my turkey flavor injector I cut the tip off and use it as a punch the needle unscrews from the injector works good..
You guys should just drill a bunch of 16th of an inch diameter holes in the plug to make it like a shower head. I'm sure all the plug is doing is acting like a slow leaking fauset.
Your making a hole in a plug that supposivly the atty bridge is touching and sucking juice threw.. when all its doing is either blocking the hole and theres a slight crack peeking threw for the jucie to drip.. too much of an opening exposed and its flooding the atty as its coming threw too fast.
You'd be better off trying to figure out how to get the bridge all the way into the plug so its making contact with the juice.. have it somewhat sealed around the bridge but still juice is gota get through somehow to the wick and down to the coil.
I'd try it but.. logic is telling me its a slow leak and dont waste your time.
The possitive from this mod is we now have a different material to use as a plug that can handle the high heat.. i've played with the cap with high voltage and it seems to handle the heat.
Actually i rolled up the sides of the cap into a spiral and shoved it into the cart with it resting on the inner lips and it worked as a plug with the opening in the middle of the spiral for the bridge to hold and the juice to flow. Worked ok.. though refilling was impossable without removing it.
Your making a hole in a plug that supposivly the atty bridge is touching and sucking juice threw.. when all its doing is either blocking the hole and theres a slight crack peeking threw for the jucie to drip.. too much of an opening exposed and its flooding the atty as its coming threw too fast.
You'd be better off trying to figure out how to get the bridge all the way into the plug so its making contact with the juice.. have it somewhat sealed around the bridge but still juice is gota get through somehow to the wick and down to the coil.
I'd try it but.. logic is telling me its a slow leak and dont waste your time.
The possitive from this mod is we now have a different material to use as a plug that can handle the high heat.. i've played with the cap with high voltage and it seems to handle the heat.
Actually i rolled up the sides of the cap into a spiral and shoved it into the cart with it resting on the inner lips and it worked as a plug with the opening in the middle of the spiral for the bridge to hold and the juice to flow. Worked ok.. though refilling was impossable without removing it.
Eclypse- Why do you seem to hate on everything I do here? you never seem to have anything positive to say unless its somthing you made.. I dont get it with you.. Did I do somthing to piss you off? are you that much of a attention .....?
No i just know enough to just look at a cart mod to understand how it would work.
Sorry.. as i always tell my wife. Ingorance is bliss and i wish i was. The more you learn about something the more you see how imperfect it is.
Hey, i wish there was one end all mod for the e-cig.. but i dont think there is atm and dont think there will be if the cart dont change. The only way its gona be perfect is if they put the cart below the atty and reverse the air flow. I guess ya gota build it yourslef.
Sorry.. as i always tell my wife. Ingorance is bliss and i wish i was. The more you learn about something the more you see how imperfect it is.
Hey, i wish there was one end all mod for the e-cig.. but i dont think there is atm and dont think there will be if the cart dont change. The only way its gona be perfect is if they put the cart below the atty and reverse the air flow. I guess ya gota build it yourslef.
- Status
Similar threads
