These tests below only note my personal opinion for the ESTIMATED ratings for the batteries I tested at the time I tested them. Any battery that is not a genuine Samsung, Sony, Murata, LG, Panasonic, Molicel, or Sanyo can change at any time! This can be one of the hazards of using “rewrapped” or batteries from other manufacturers so carefully research any battery you are considering using before purchasing.

Misusing or mishandling lithium-ion batteries can pose a SERIOUS RISK of property damage, personal injury, or even death. Never use them outside of a fully protected battery pack and you use them at your own risk. Never exceed the battery’s true continuous discharge rating (CDR), never let it get colder than 0°C or hotter than 60°C, and keep the plastic wrap and top insulating ring in perfect condition. Never use a battery that is physically damaged in any way.

Testing batteries at their limits is dangerous and should never be attempted by anyone who has not thoroughly studied the dangers involved, understands the risks, has the proper equipment, and takes all appropriate safety precautions.

If the battery has only one current rating number, or if it only says "max", then I have to assume the battery is rated at that current level for any type of discharge, including continuous.




Test Results
It’s been four years so it’s time for a retest. This Keeppower is a decent performer and no longer uses the very inconsistent Yong De Li New Energy co. (YDL) cell, which was sometimes better performing but only if you got a “good” one. This cell used by Keeppower and some others is better but 18350’s are still more inconsistent than larger cells.

This Keeppower’s capacity rating is exaggerated. The two cells I tested delivered 1126mAh and 1132mAh. This is below this cell’s 1200mAh rating and since I cannot have the two lowest capacity cells in the batch I am rating them 1100mAh.

The 10A rating pushes them hard so I recommend, like with all cells, operating it at lower than its rating. For best performance (not lots of voltage sag) and long cell life I recommend staying under 5A-7A (15W-21W). Charge at 0.5A or lower!

The 15A “Max Pulse” rating will result in HUGE voltage sag and very short run times. If you are pulsing at current levels this high do not allow the cell to get hotter than 60°C to help lower the risk and extend cell life.

This cell has an extra line of sealant or epoxy at the top, where the rolled over edge of the metal can meets the top plastic sealing ring. I have never seen this on any other cell and I do not know why it is there. Rust prevention (when used in a humid environment) at the edge of the metal can perhaps? I scraped out this sealant/epoxy and did a few cycles of high-current pulse discharging without problems. I do not think the sealant/epoxy line is there to help keep the cell from leaking.


Continuous Current Discharge Graphs



Ratings and Performance Specs Graphic



18650 Ratings and E-Scores Table:


20700/21700 Ratings and E-Scores Table:

I want to work for the community full time! If you feel what I do is worth a couple dollars a month and you would like early access to battery availability, battery testing and news, and a say in what I test, then please consider becoming a patron and supporting my testing efforts: Patreon.

To see how other cells have tested check out this link: Links To All 21700, 26650, 18350, 18500 Battery Tests

I will add stuff as I find it.

SKRR sub ohm tank by Vaporesso, nib. Have to ask for $7 to cover s/h. PP F&F only with no mention of vape etc. I have several, this one is gold:



I think the Berserkers are v1, both are regular size. I built a coil on one of them and that is as far as I got. I hate building so never used these. SS and a gold one. $13 each w/shipping to US only. PP with no mention of vape etc.




NIB red Vaporesso NRG tank w/2 cores, $10 w/shipping to US


NIB Wismec Luxotic BF squonker, opened for pics only. $15 w/shipping to US, PP F&F only with no mention of ecig, vape etc.

Hey guys me again,
Ive just got myself a steamcrave meson rta and thrown in a vv single ss316 alien coil .3ohm im liking the vape at about 40w and have started to try out tc mode and not sure what i should be setting the wattage and temp too ive tried going to 50 60w with the wattage and 200c but it doesnt get a chance to get that hot. So i gone down to 40w and 125 degrees Celsius and it seems to be a nice vape but how exactly does it work should i be going way higher with the wattage and low with the degrees or just go up on both and be light with the fire button and just have it not burn my juice and coil. As described its a thelema solo the quest version not the dna. Thank in advance.

Hello and welcome back for another review. This time I will be covering the Thunderhead Creations Mech Boro Mod that was sent to me by Sourcemore in order to provide you with a fair and honest review. In case you don’t know what a boro mod is, a boro tank I believe was originally used in Billet Box type mods where the tank sits inside the mod which is then called an All in One mod or AIO. These tanks can be used on many Boro devices and can be either rebuildable or use factory coils like PNP or Nautilus coils. I’m sure there are more but those are the two that I am most familiar with. The Tauren Mech Mod can be purchased two different ways. It can be purchased as an unregulated mechanical mod only or can be purchased with the X Chip which makes it a semi regulated mod. I would not recommend purchasing the unregulated version unless you are very familiar with ohm’s law and using the proper coil resistances for the batteries that you are using.

The Tauren Mech Mod is compatible with 18650, 20700, and 21700 batteries depending on the configuration you choose to use. The last two are only compatible when not using the X Chip. The connections inside are 24k plated to ensure a good connection and can be used with most boro tanks as far as I am aware. I have a few different ones and will test the unit with these. There is also a 510 build deck adapter that I will talk about more later. In the past I have been very pleased with all of the THC tanks that I have tested so have been looking forward to testing out this new mod.



WHAT’S IN THE BOX?

1* Tauren Boro Mod
1* 21700 Battery Cap
1* 18650 Battery Cap
1* 510 Adaptor
1* Coil Leg Trimmer
1* 510 Build Deck Insert
1* Multifunctional Wrench
1* Thanks Card
1* Warranty Card
1* User Manual
Spare Screwdriver & Screws & O-rings

SPECIFICATIONS:

FEATURES:

1. Compatible with 21700/18650/20700 battery

2. Multifunctional wrench and build deck included

3. Compatible with Tauren Boro Tank

4. Full mech mod only

5. Compact mini size & elegant

6. 0.1s fast boost, 0.1ohm support

7. 10s auto cutoff, 510 build deck

8. Full 24K plated inside, strong connection

9. Multiple modes: 18650 mech mode, 20700/21700 mech mode

10. Safety protections: Short Circuit/Over Discharge/Battery Reverse/Over Temperature Protection (WHEN USING X CHIP)

INITIAL THOUGHTS:

The version that I received for this review is the blue Mech version that does not include the X Chip which adds some safety features to the mod but only fits in the mod with the 18650 battery and taller battery cap. I won’t be covering the X Chip since I didn’t receive it for testing.

The packaging for the Tauren is really pretty nice in my opinion. The front of the box has the Tauren symbol and name near the top in a metallic looking color and below it lets you know that it was designed and manufactured by Thunderhead Creations. There is a clear viewing window that allows you to see one side of the mod before opening the box. I’m sure it was done on purpose like this so that the badge on the side of the mod was visible.

The back side of the box has the same Tauren logo and name as well as the THC logo near the top in gold. It gives a rather lackluster description of the contents of the package and the THC website near the bottom.

The box is opened by pulling on the cloth tab that is protruding from the bottom long side of the box. Once opened, you get a better look at the contents of the box which includes the mod itself, coil cutting guide, long battery cap for use with 21700 batteries, build deck adapter, and 510 adapter for dry burning coils. There is a spare cut out in the foam for the X Chip but as I mentioned, I received the mech only version without the chip. The user manual is located underneath the foam insert along with the Tauren wrench which can be used to help in removing the battery cap as well as the boro nut that secures the tank in place. I was a little surprised that there is no tank included in the kit so if you are wanting the Tauren boro tank then it will have to be purchased separately.

This is a mechanical mod so there is no display to discuss. It’s definitely a good idea to know ohm’s law and your battery capacity when using a mechanical mod. I personally do not normally use mechanical mods. If you aren’t familiar with ohm’s law then free calculators can be found easily online. It will tell you how many watts and amps a particular coil resistance will draw from the battery so you do need to know the rated ampacity of the battery you are using. This battery information can be found from the place that you purchased it or better yet take a look at Mooch’s battery reviews. His reviews can be found here Home - Mooch Batteries Reviews Blog.

The front of the mod has the door that covers the boro tank that you choose to use with the mod but has a large opening. Near the top is what I am guessing is a serial number and below the opening are five round airflow holes. Near the bottom is the fire button. This button has kind of a spongey feel to it. I personally am not crazy about the placement of the button here. I am normally a person that likes to use my thumb to fire a mod but with this one the only comfortable way I could find to fire it is with my hand wrapped around the battery tube and fire it with my middle finger. The mod has four magnets and the door has four magnets as well on the back side to hold the door on very securely. They are so strong that sometimes it’s a little bit of a struggle to remove the door. In the last picture below you can see the gold plated contact that meets up with the bottom contact of the boro tank. The center screw has a slot cut in it so it can be removed for cleaning and is adjustable to better fit some tanks. The drip tip that is included is replaceable. At first I thought it was an integrated tip but pretty quickly discovered that it was not after trying to tighten the boro nut by turning the tip. I quickly replaced the included tip with one of my favorite integrated tips. These eliminate the need to use the Tauren wrench to tighten the nut.

The mod comes with the short battery cap pre-installed on the mod which is only able to be used with an 18650 battery and does not allow room for the X Chip. In the kit however is a longer battery cap that allows the user to use an 18650 with the chip or a 20700/21700 without the chip. The battery is loaded with the negative post pointing up towards the threaded cap. The polarity is not marked inside the mod which would have been a nice touch. However, the inside of each battery cap has a – symbol engraved into the contact. I experienced some difficulty trying to thread on the shorter battery cap. It was a little tough to get the threading started because the mod body gets in the way. I ended up running the mod most of the time with the taller batter cap and a 21700 battery. The longer cap gives you more room to get a grip on it to get it started. Also the short cap is a little difficult to unthread because of a lack of area to grip which is where the included wrench can come in handy to help you get the cap started to unthread. The wrench can also be used to tighten the boro nut with whichever boro tank you decide to use with the mod.

One side of the mod has a gold badge shaped like the Tauren symbol. I personally think that the badge would have looked better in stainless steel to match the stainless battery tube. There is an opening on either side so the boro tank is exposed and can be seen. Both sides of the mod have three slanted oval holes that allow plenty of airflow for the tank.

The base of the mod has the THC logo and Thunderhead Creations name printed on it. The base is held in place with two torx head screws which I’m assuming can be removed for cleaning the mod. Also on the bottom are seven holes in a circular pattern which serve as a safety feature in case of battery venting. This is definitely a good idea in a mechanical mod.

Included in the kit is the Tauren build deck and a 510 adapter. The build deck is inserted in the mod in place of a boro tank and the 510 adapter screws in from the top in place of the boro nut in order to provide the user with the ability to dry burn coils. Of course the boro tank you are using would have to have a 510 threaded connector on it to use it like this. From what I understand, the Tauren boro tank does have such a connection. I guess you could also use this to fire a tank but that is not the intention. I personally have a little bit of an issue dry burning a coil on a mechanical mod. A lot of boro bridges don’t have a lot of room to build in and one could easily have a shorted coil which would not be a good situation when trying to dry burn the coil on a mechanical mod. I did try dry burning a coil with my first build in the Ether boro tank that I used and it burned the coil to the point where every puff tasted burnt and I had to install a new coil.

FINAL THOUGHTS:

I was a little late to the game when it comes to THC devices. I have tested a few of their tanks and have been impressed with the build quality and performance. I’ve never been much of a mechanical mod user even in the earlier days of vaping when there wasn’t much available on the market.

I tried two different tanks in the Tauren which were the Ether boro tank and another tank that uses nautilus coils. Both worked fine in the mod without issue. I used a MTL Clapton ni80 wire to wind a .7 ohm coil in the Ether boro tank. Initially with a fully charged 18650 battery it seemed to hit well but after a short while I was finding myself wishing it was a regulated mod where I could turn the wattage up. After that I used a 21700 battery with the same tank and could immediately tell that it seemed like the mod hit harder with the larger battery.

The Tauren mod does work as promised and looks good doing it. Remember that these are my personal opinions and that I am not a seasoned mechanical mod user. I will say that the Tauren is smaller and lighter than what I expected from a mod like this. To me it doesn’t seem to fire quite as fast as another mechanical mod that I used before. For me the fire button placement is a little awkward and feel like since it is a mechanical mod with this type/position of fire button that there should be some way to lock the fire button. My other complaint is that it doesn’t come with a tank. I wish they would have included the Tauren boro tank and adjusted the price accordingly. It is good that there are a couple different battery configurations. I didn’t get the X Chip with the kit I received for review but wish that the chip could also be used with the 21700 battery for maximum battery life.

I hope that I have done a well enough explanation of this mod for you. Some might love the Tauren Mech Mod but for me personally it’s probably going to be a no go. It just doesn’t fit my vaping style well. I’d like to thank Sourcemore and Kavis for sending the Thunderhead Creations Tauren Mech Boro kit for this review. Thanks also to the readers for making it to the end of yet another review. Below is a link to the website if you would like to purchase one yourself. There isn’t a coupon code on this one.

ThunderHead Creations Tauren Mech Boro Mod (sourcemore.com)

Kayfun clones (white, black, gold) NIB from Ehpro. $13 each or $30for all 3. Includes s/h to US. Payment via PP, F&F with no mention of ecig, vape etc. Extras included as pictured.






NIB Wismec Luxotic BF squonker, opened for pics only. $15 w/shipping to US, PP F&F only with no mention of ecig, vape etc.


Lucid Kit, nib, opened for pics only. About the size/style of the Pico. $17 including S/H to US, PP F&F with no mention of ecigs, vape etc.


NIB red Vaporesso NRG tank w/2 cores, $10 w/shipping to US

I used to be into vaping making my own liquids, attys etc..
Then got tired of it and stopped vaping for years.

Got back to it with a Vuse and a Leap, realized too expensive but liked the no muss, no fuss
aspect of it. How low have the mighty fallen. Ha Ha.
Researched a whole bunch and ended up with the Joyetech WideWick mostly because I was intrigued
by the Pod Wicking system.

I'd like to emphasize that the Wide Wick System is a big win. No leaks, no dry hits Sputtering etc.. just a consistent vape.
Really does what it's supposed to do very well.

Others on this thread have put extensive reviews but this thread is limited to my impressions about a simple
device for those who like the disposable pods.

Pros

A. Atty is in the Pod. Vape it for a few weeks than an Easy Pod Change
B. No Buttons - Just fill and Vape Away
C. USB C Charging on bottom. No leaks when charged on the side and just about everyone should
have a USB C Cord.
D Top fill with pressure seal. Just stick the tip in and fill. Easy Peasy (That's what she said)
E Only one type of Pod is available 1.2 ohm. And this vapes around 12 Watts. No need for Pod Decisions. It's up to you
to tailor the strength of the Liquid to provide the right Vape.
E Vape quality. With a 50mg Salt Juice 50/50 PG VG the vape is like the Juul Vuse or Leap except depending on the liquid you use
tastier.
F Airflow control Two holes on each side cover one with your hand or scotch tape and the draw is more restrictive.
G. Very sleek design looks like a giant Bic Mini lighter. Unobtrusive. Very Light weight
H. the Pattern on the outside is very understated.
I. Economical the Device is easily found online undes $10.00 (I paid $8.95). ThePods with built in Atty are only around $2.50 - $3.00 a piece(I Paid $2.50) and are supposed to last 2-3 weeks

Negatives
1. No extra features a battery indicator would have been nice
2. If you are into sub Ohm vaping or low nic juices this is not for you . Vapes too cool.
3. Airflow Control - Would have been nice to have a Air flow control
4. A little longer than I'd like can't completely cover unit with my hands when stealth vaping.

Final Impression
This is all about not having to make decisions. Just fill and Vape.
It's a 5 star vaping device for the crowd that likes low watt high nic juices and above all simplicity.

Some people just want to easily fill a pod and start vaping with the only decision being what liquid to put in.

They also want a more low key looking device that won't attract scowls or attention.

Comments or questions are welcome

Hello and welcome back for today's review of the UWELL Crown B Pod System, this pod system is in my opinion a perfect starter kit while still having great features for a seasoned vaper looking for a simple easy to use device. Being a pod system you won't get a full days worth of vaping like a full sized device can give but it does alright for what it's designed for. Having a internal 1150mAh battery and the ability to use it as a DTL, RDL, or MTL device adds to it's features of 3 power levels, 2 supplied drip tips of different bore sizes, fully adjustable airflow and the ability to vape while charging. After some manufacturer information I'll give you my findings on this pod system.





COLOR CHOICES - ( IRON GREY ONLY )





IN THE BOX


* Crown B Pod Kit Device

* 1pc Crown B Empty Cartridge

* 1pc Uwell PA Coil 0.3ohm (DTL) (Pre-Installed)

* 1pc Uwell PA Coil 0.8ohm (RDL & MTL)

* User Manual

* Type-C Charging Cable

* 1pc 510 Drip Tip (Pre-Installed)

* 1pc 510 Drip Tip for MTL or RDL (Spare)




SPECIFICATIONS

• Dimensions: 92 x 42 x 18mm
• Material: PCTG / Zinc Alloy
• Weight: 82g
• Display: 3 colour light
• Battery: 1150mAh (internal)
• Pod capacity: 2ml / 3.5ml
• Output: 13-35W – 3 power levels
• Type C USB charging – 2A charge rate
• Coil: Uwell PA mesh coil 0.3ohm (25-35W) / Uwell mesh coil 0.8ohm (15-18W)
• Resistance range: Not specified
• Airflow: Adjustable slider
• Filling: Side fill
• Activation: Auto draw or fire/activation button

AVAILABLE COILS





FULLY ADJUSTABLE AIRFLOW CONTROL ( SLIDER )






MAGNETIC 3.5 ML POD CONNECTION





MANUAL BUTTON FIRE OR AUTO DRAW

A very thorough and flawless transaction! Would definitely do business with again in the future.

I think the Berserkers are v1, both are regular size. I built a coil on one of them and that is as far as I got. I hate building so never used these. SS and a gold one. $13 each w/shipping to US only. PP with no mention of vape etc.





IRoar, TC 18650 kit w/tank, NIB. This is the same as the original Coolfire. $15 w/shipping




Dovpo , for use with mechanical mods $7 w/shipping



1 box pf 5 baby beast T8 coils, compatible with Melo 3 if anyone uses these anymore. $4 with shipping.



Wismec Predator dual 18650, 228w. White, barely used. Even though I have the box, it will ship without it due to shipping costs. $13 w/shipping to US



SOLD----Geekvape Blade, Swift. 235w, dual 18650 batts Used only for testing, nib $35 w/shipping to US


.2ohm Drip Box Coils, 3 boxes if anyone uses these before I dump them. U pay shipping, probably $4


Geek Vape Lucid Kit, nib, opened for pics only. $18 including S/H to US, PP F&F with no mention of ecigs, vape etc.

Sale time: Sept. 1st - Sept. 4th

10% OFF SITEWIDE Coupon: LAB10
Bronze Level Exclusive 5% OFF Coupon: LAB5 (Must log in)

Enter here<<<Sourcemore.com - E-cigarette, Electronic Cigarette Online

Hi guys, this fall's most important vape mod kits have arrived, It is Rincoe Jellybox XR Vape, with 228W output, super powerful steam function, and excellent appearance design is deeply loved by the market.



Jellybox XR Vape is mainly composed of a Box Mod and an MTL Tank. Next, we will introduce it in detail from these two parts.

Rincoe Jellybox XR Box Mod

The exterior continues the transparent PC cover and zinc alloy frame that are the hallmark of the Rincoe Jellybox series, and the 3D printed pattern is vivid and realistic, reflecting the design aesthetic.

The dual 18650 battery unit (not included), rated at 228W, can be bundled with Rincoe Jellytank or other 26mm diameter atomizers.

Equipped with a 0.96 "TFT screen, it can meet different needs through a main button, two adjustment switches, control wattage mode, or temperature control mode.

Rincoe Jellytank Atomizer

The Rincoe Jellytank is a transparent e-cigarette can that can hold 4.8 ml of juice. It is made of durable stainless steel and PCTG, which ensures a long service life and beautiful appearance.

The 510 threaded connection makes it easy to assemble, and you can choose from a variety of colors to customize your atomization experience. Rincoe Jellytank is suitable for MTL(mouth-to-lung) atomization and has a convenient top-fill system.

All in all, if you are a player who likes to customize the Steam experience, Rincoe Jellybox XR will be more suitable for you, of course, the simple and clear operation is also friendly to novices, I think it is a breakthrough in the steam world, like the challenge you should not miss!


More vape kits you Like:

little vape
fruit e juice

Introducing the game-changing hyde n-bar 4500. It's where innovative design meets an unforgettable vaping experience.

Step up your vaping game with elf bar airo max 5000. This is not just another vape; it's a statement of sophistication.

Wenax S3(Stylus 3) Kit is powered by a built-in 1100mAh battery with 18W max to priovide marvelous 2-day-use battery life and consistent taste. It supports 3-level output adjustments: (Red: Low, Blue: Med, Green: High) and precise airflow adjustment to bring you various taste. Designed with boost mode, you can press the button to activate the max output for the max clouds. It also features device lock button and supports auto draw or button-triggered to bring you easy and convenient use. By adopting intelligent 360° ring indicators, it can show the battery status clearly. The latest VPU tech inside can provide mellower taste, longer usage lifespan and safer vape. It is compatible with GeekVape S 0.8Ω/1.2Ω Cartridge(Coil is not replaceable) that can work with ergonomic & filter drip tip to bring you different vaping experience.

Sourcemore × GeekVape Wenax S3 Kit Giveaway, 2 winners, ends on Sept. 7th, 2023

Enter here

Innokin Klypse Kit allows you to navigate the MTL experience, the 2ml pod cartridge has an integrated 0.8ohm coil and features a side filling design. It has no adjustable airflow and captures a semi-restrictive MTL vape via its two fixed pinholes. Designing a 700mAh built-in battery, it has one hour of fully charged and gains a max 16W output. It optimizes a concealed LED light to check the battery level.



Features:
1. MTL Experience
2. 2ml Pod Cartridge
3. Integrated 0.8ohm Coil
4. Side Filling Design
5. No Adjustable Airflow
6. 700mAh Built-in Battery
7. Max 16W Output
8. Concealed LED Light
...

Click here for more:

Innokin Klypse Kit: Innokin Klypse Pod System Kit

Dive into the world of flavor and quality with the hyde retro rave 5000. It's more than just a vape; it's a lifestyle.

Great transaction and good communication.

Ultra fast shipping, good packaging, everything as described. Perfect across the board!

To @Tonee N for getting those revenant squonkers out to me so quickly and in such beautiful condition. Can’t say enough great things about doing ‘business’ with this person and recommend buying again from them! Sorry it took so long getting this out here but as most know I’ve had some health issues and appreciate your patience with me.

Sara

SOLD----First up is a Stentorian Ram BF squonk mod, nib. Comes with 3 bottles. $15 w/shipping to US.

Stentorian RAM BF MOD An elegant Squonker device with a bottom feeding design. Powered by a single 18650 cell, plus a 7ml huge Squonk bottle, the RAM BF MOD offers a full day vaping without frequent refilling. It has a fire button with a safety lock to prevent accidental firing too.



Smoant Charon, black mini, nib kit with sub ohm tank, $15 w/shipping to US


8 Geek Vape 6.5 ml squonk bottles, nib Prefer to sell as a lot for $20 with shipping to US. Might split if desired.


Asmodus Colossal, nib, grey $17 including shipping to US


asMODus Colossal 80W Touch Screen Box Mod Features:

• GX-80-HUT V2 Touch Screen Chipset
• Single 18650 High Amp Batteries - Not Included
• Wattage Output Range: 5-80W
• Max Voltage Output: 7.5V
• Temperature Range: 212-572F
• Atomizer Min Resistance: 0.1ohm
• Versatile Temperature Control Module
• Supports Ni200 Nickel, Titanium, and SS 304/316/317 Heating Elements
• Temperature Coefficient of Resistance (TCR) Functionality
• Temperature Factor of Resistivity (TFR) Functionality
• Two Power Modes - POWER & CURVE

NIB, green Zbiip. $13 including shipping to US.

SPECIFICATION​

Blue is sold......These are basically nib squonk mods, I might have tried them for a few minutes, if that. Pretty blue stabwood, what more can I say. Comes with 2 bottles.




Green Stabwood


Purple


I bought this one used and it has no bottle.


Not sure what happened to my pricing but anyway, $18 for the green or purple and if you want all 3, $35 w/shipping to US. PP with no mention of vape, ecig etc.

So, unfortunately my fiance waited until after I bought and used all of this stuff before telling me he doesn't really want me vaping again. I was only doing it for flavor and fun, so it's no big deal for me to quit it again, but I can't return this stuff that I spent a bunch of money on now.

The Legend and the Z-Max are like new. The Legend has 400 hits through it as 150 of the 650 were factory test hits. The Z Max has maybe 150 hits through it, I wasn't a fan. It still has the replacement glass, the extra coil it comes with, plus an extra coil. Both have their original boxes and covers, I just forgot the Legend cover at home.

The Valyrian 2 is clearly two Valyrian 2 combined, but it works flawlessly and comes with 3 new coils. The Falcon 2 is in very good shape and comes with a new coil.

The two bottles of juice are Blue Agave Nectar and White Zombie which is a strawberry ish flavor. The White Zombie is around 95% full and the Blue Agave is about 90%.

The batteries in it now work okay but they're getting super old so probably better to just get new ones, but I can give them too if you want.

I'd like to get $80 shipped in the US for everything but I'm open to offers since I don't have Facebook and can't sell them on Marketplace.