• Locked
Bench Test Results: Epoch Protected 8A 3500mAh 18650…USB chargeable Sanyo NCR18650GA

These tests below only note my personal ESTIMATED ratings for the batteries I tested at the time I tested them. Any battery that is not a genuine Samsung, Sony, Murata, LG, Panasonic, Molicel, or Sanyo can change at any time! This is one of the hazards of using “rewrapped” or batteries from other manufacturers so carefully research any battery you are considering using before purchasing.

Misusing or mishandling lithium-ion batteries can pose a SERIOUS RISK of property damage, personal injury, or even death. They are not supposed to be used outside of a fully protected battery pack and you use them at your own risk. Never exceed the battery’s true continuous current rating and keep the plastic wrap and top insulating ring in perfect condition.

Testing batteries at their limits is dangerous and should never be attempted by anyone who has not thoroughly studied the dangers involved, understands the risks, has the proper equipment, and takes all appropriate safety precautions.

If the battery has only one current rating number, or if it only says "max", then I have to assume the battery is rated at that current level for any type of discharge, including continuous.

F0FBDE65-3D12-41DE-89FD-187AD793BD5A.jpeg 2B371AB8-973C-47F7-994A-0781B3579CB4.jpeg 1ADD8E80-02E0-41BB-A574-221DFBC9DC5E.jpeg 3AE9ECBE-1484-4962-B779-ED7F76308879.jpeg F74FC980-2526-4B1A-BE5B-3D937AABC1F9.jpeg


Test Results
This is a protected version of the great performing Sanyo NCR18650GA that also has a Micro-USB charging port. Its 8A rating seems reasonable as the 10A rating of the NCR18650GA can cause accelerated aging of the cell (according to the Sanyo datasheet).

The protection circuit is rated at 2.5V and cuts off the cell at about 2.4V during a 5A discharge, with the voltage bouncing back up to over 2.7V once the protection circuit was reset. The reset is done by starting to charge the cell and has to be done using the USB port. This is because many round cell chargers will not start charging this cell after its protection is activated since its voltage is close to zero volts. Once the protection circuit is reset via USB though you can use a standard round cell charger if you want.

The overcurrent protection spec for this cell is 12A. The protection did not activate at 10A and did activate at 15A, with a maximum cell temperature of 51°C when the protection was activated. The 12A cutoff could vary a bit from cell to cell but the rating seems reasonable.

The two cells I tested delivered 3427mAh and 3471mAh when charged using my standard method. They delivered 3415mAh and 3445mAh when using the USB port for charging. This is not great consistency but is acceptable and the usual slight loss of capacity caused by the protection circuit did not force this cell below Sanyo’s 3350mAh minimum capacity rating for the NCR18650GA. Neither cell met Epoch’s 3500mAh rating though.

The USB port charged this cell at 0.5A-0.65A, depending on the temperature and how far along the charge was. The top contact of the protection circuit reached 70°C maximum, hot but not unacceptable. The cell did not get hot.

The protection circuit is inside a metal cap that is press fit over the cell and is very secure. The bottom of this cell is covered by a piece of metal spot-welded to it. I do not know why but perhaps to help prevent the bottom from possibly denting?

The protection circuit and bottom plate makes this cell about 70.2mm long and the double wrapping makes it about 18.4mm round (diameter). Probably too long for any vaping device and confirm that your flashlight can fit this cell.

Two cells were donated for testing by 18650BatteryStore (18650 Battery Store - Lithium Ion Batteries, Chargers and Accessories). Thank you!


Continuous Current Discharge Graphs
114BC6ED-80C3-4866-80FD-EF70183AD750.jpeg 354C741C-5149-4661-A107-BAF7F1CACBDE.jpeg 37F2D8FA-0000-4543-BF0D-4CE5534ED9CD.jpeg


Ratings and Performance Specs Graphic
03E8B808-9BA0-40FE-B652-3A6F3C24602F.jpeg

I want to work for the community full time! If you feel what I do is worth a couple dollars a month and you would like early access to battery availability, battery and charger testing and news, and a say in what I test, then please consider becoming a patron and supporting my testing efforts: Battery Mooch is creating battery and device tests | Patreon.

To see how other cells have tested check out this link: List of Battery Tests | E-Cigarette Forum

  • Locked
WHAT`S THE DIFFERENCES BETWEEN OXVA ARBITER SOLO RTA AND ARBITER RTA?

OXVA ARBITER SOLO RTA is the upgraded version of OXVA Arbiter RTA. Arbiter Solo RTA inherits the top to bottom airflow. What's more, OXVA Arbiter Solo RTA is the first dual airflow system RTA with airflow coming from top to bottom and side. Arbiter Solo RTA is easier to switch between MTL and RDL. Just turn the top ring to switch between MTL and RDL. Turn left to close the side airflow and you would get a perfect MTL; Turn right and you would get a RDL RTA.

From the below chart, you can check the similarities and differences between OXVA Arbiter Solo RTA and OXVA Arbiter RTA clearly.





Similarities:
1. Top filling design
2. Top to bottom airflow
3. Leak-proof
4. 510 drip tip
5. Easy to build single coil



The improvements:
1. Arbiter Solo comes with 25mm diameter to compatible with most atomizers.
2. Arbiter Solo features dual airflow system.
3. Arbiter Solo can switch between MTL and RDL quickly.
4. Arbiter Solo adopts tiny inner chamber for awesome flavor.
5. Arbiter Solo is almost completely leak-proof due to the top AFC.



Don't hesitate to take it home from Everzon, you will love it.
-----------------------------------------
Free Shipping vape devices
New Arrivals
Clearance
Daily Deals
Box Mods
IN STOCK VAPE DEVICES
$0.01-$19.99 Cheap Deals
Coupon Codes

  • Locked
COMPARISON BETWEEN VOOPOO VINCI 2 and VINCI X 2

Everzon launched both VOOPOO VINCI X 2 and VINCI 2. The only difference is the battery. VOOPOO VINCI 2 Kit has a 1500mah built-in battery with max 50W output. VOOPOO VINCI X 2 Kit is powered by single 18650 battery with adjustable wattage of 5-80W.




VOOPOO VINCI X 2 / VINCI 2 features Brand-new Gene.AI 2.0 chip with Smart/ RBA modes and 1.08 inch TFT color screen with dual UI theme interface. Smart mode automatically identifies the inserted colis and matches it with the best power, which is especially suitable for beginners. The RBA mode with no power limit can be enjoyed by professional players. Both of them adopts infinite adjustable airflow system to support the regulation of any size of airway and is compatible with all PnP coils.

Voopoo Vinci Series gives you the best vape where you can utilize your best moments at making the biggest clouds. Voopoo won't let down their consumers. So, what are you waiting for? You can easily try VINCI X 2 / VINCI 2 from Everzon.


-----------------------------------------
Free Shipping vape devices
New Arrivals
Clearance
Daily Deals
Box Mods
IN STOCK VAPE DEVICES
$0.01-$19.99 Cheap Deals
Coupon Codes

  • Locked
Nic salts and DL hits?

I’m curious as to why you shouldn’t do DL when using nic salts. I’ve got an Aegis Hero with a 0.6 coil at 15 watts. Even with the airflow closed off, it’s still to loose for a MTL. I keep reading and hearing I shouldn’t use nic salts for DL. The worst thing I’ve experienced so far is a mild headache. The nic salt is a 30mg.
Thanks in advance. ECF is my only true support group and I’m having a really hard time not smoking the stinkiest. Been back to vaping for about a month, and keep telling myself it’s all about baby steps. Not how many I smoke but how many I don’t smoke. I’ve got to quit for health reasons.

  • Locked
First Look-Suorin Trident Pod Mod Kit

Hey guys. Today let's check out the Suorin Trident Kit. If you want a pod mod with a fast firing speed, then don't miss out on this.

Suorin Trident has a record firing speed of 0.006s, which is ideal for users who are looking for some strong power output with a short ignition delay. With a cylindrical zinc alloy shell, the back is decorated with a huge carbon fiber lining, the profile of the fuselage is inspired by the SLS racing version, and its hand feels perfect when gripping the device. Excellent atomization power and uncompromising lightweight structure bring you a high-quality experience of vaping. Trident is powered by a single replaceable 18650 battery (not included). To replace the battery, just unscrew the battery cover on the bottom of the device. Equipped with a Type-C port to help optimize charging efficiency and service life. Drive vaping passion with efficiency. Suorin Trident uses an intelligent ORI chip internally, which adds a new look to voltage regulation-automatically achieves a perfect balance between wattage and mesh coil, and you can also adjust it from 5W to 85W according to your own preferences. With the function of voltage management, power distribution, temperature management, and atomization monitoring, the ORI chip can accurately control and manage the entire process of atomization. ORI chip can also be compatible with different atomization coils such as single mesh and triple mesh coil, ensuring you the best performance of atomization. In addition, it is also equipped with an innovative boost converter: constant voltage output for steady performance even as your battery level goes down.
suorin_trident_pod_mod_kit_85w.jpg

At the top of Suorin Trident is a pod cartridge that holds up to 4.4mL of e-liquid and is easily refilled through a bottom fill port. 4.4ml capacity can bring you a long-term atomization effect and reduce the filling time. Through the visible oil level window, you can clearly see the e-juice level. The new 0.4ohm TRI single mesh coil (interchangeable) and 0.2ohm TRI triple mesh coil are used in the pod. Single-hole mesh coil is designed for pure flavor and more subtle clouds, while three-hole mesh coil has larger clouds and provides a strong flavor. All do-it-yourself coil build users can use an additional TRI-RBA coil (not included). With the dual airflow adjustment dial, Trident can precisely adjust the airflow to maximize the overall atomization efficiency. And the individual airflow setting is carried out directly on the bottom side airflow control ring of the coil.

Check for more details here: Suorin Trident Pod Mod Kit 85W

You may also like:
obelisk 120 fc price
smok novo 4 review

  • Locked
DDVAPOR DDZE Disposable Vape Kit - great way to stay off cigarettes

The DDZE disposable device has a capacity of 11 ml and can provide you with 3000 suctions in one device. You can find this feature in some sub-ohm and advanced modules, but want to find it in a disposable pod? This is innovative. It takes most of the features you appreciate in large vape devices and is recreated in a lightweight, easy-to-use disposable device that you can discard after use.
ddvapor_ddze_disposable_vape_kit_flavors.jpg

Features
• Unique box mod style design
• Best premium flavors
• Colorful glow at the bottom
• 3000 puffs per device
• 11ml of e-Liquid per device
• 5% Nicotine strength

No recharge or mess up your device due to overflowing eJuice. No professional knowledge is required, just open when exhausted, pull and discard. DDZE Disposable's pre-packed vape e-liquid is formulated with 5% nicotine. Each pull will produce a smooth and strong blow. The device has a built-in 1.7ohm cotton coil. It can heat eJuice at the right temperature and enhance the flavor.

The disposable pods produce enough steam, which is necessary for a good vape experience. If you are a transitional e-cigarette, this is a good way to quit smoking permanently. The bottom of the DDZE disposable device also uses an LED light design, which can emit colored light.

Other kits you may prefer:
suorin air mod kit price
lost vape thelema dna250c kit price

  • Locked
What's the best coil to get for mouth to lung vaping, Voopoo drag x.

At Element Vape, there are about 10 kinds of coils listed that fit the Voopoo drag x. I'm not sure which one to get but I like mouth to lung vaping so if someone could assist me, I'd appreciate it.

Also, if I am using the device for mouth to lung vaping, am I supposed to keep the air hole open, closed or halfway? Thank you in advance.

  • Locked
What to expect with salts?

I’m a long time vaper. I have been vaping 83/27 PG/VG juice with 12-16 mg nic. I use an avacado tank with dual Clapton coils at .3 ohms and around 50-60 watts. With this config I can get my most desirable lung hit but only with certain juices and I tend to chain vape. Whenever the shop is out of my regular juice I’m always Leary picking something new because a lot of times even at the same nic level I don’t get the satisfying lung hit I crave and end up with a sore throat from hitting it so often. Soo... I moved to Hawaii and my system is all screwed up. The juices here are all 50/50 so super watery, the juice is also double the price, I burn through it twice as fast, the lung hit is barely there, and it pops and crackles really loud which drives my wife nuts and has cuased many arguments about my “stupid crack pipe”. So in an effort to make my wife happier, spend less money, and maybe vape less I decided to venture into the salts realm.

I started with a geek bar to test the waters and lung hit was phenomenal! But at $20 a pop and only lasting a day that just wasn’t going to work. So after much research I just picked up a SMOK NORD 2 and some 48mg juice. I set it for 50 watts and took my first drag. Good god almighty! One hit and I caught a buzz. I have NEVER caught a buzz from a vape before. After some messing around I dialed it down to 25 watts and so far seems like the sweet spot and I don’t have the urge to chain vape... so success? I don’t know yet? It’s for sure a lot quieter and 1/4 the size of my tank MOD. Does going from chain vaping 16mg to 48 salt nic seem excessive or about right? I may try the 24mg juice when this one is out but any other suggestions? I’m a little worried I’m going to give myself nic poisoning after that first drag lol

  • Locked
Coming Soon! Eleaf iStick Pico Plus 75W Kit

This new kit features 75 watts of power, stable performance, a smart chipset, a USB-C charging port, single 18650 battery support, effortless battery access, sub-ohm coils with AST steel heating elements for fast heating & flavor, and a 4ml juice capacity.

The Eleaf iStick Pico Plus Kit produces incredible vapor and flavor in two different ways. On the mod level, the smart chipset is built with a coil protection system that prevents dry hits so you may get the best possible flavor production. But, that is not all. The tank also uses innovative AST-Steel heating elements that are said to heat fast, boost flavor, and enhance lifespan. This means that overall you may rely on this new setup to produce reliable, flavorful puffs. iStick Pico Plus Kit comes with two coils, both of which are sub-ohm, so they are best used with standard e-liquids. In the box, you will find both an EC-A 0.3ohm and 0.5ohm head.



The Pico Plus works with a single 18650 battery conveniently accessed via a top screw cap that is adjacent to the atomizer. Additionally, recharging this battery via the brand new USB-C charging port is so fast because of the lightning-fast 2 amp capability.
...

Click here for more:

Eleaf iStick Pico Plus Kit: Eleaf IStick Pico Plus 75W Kit With Melo 4S Tank Atomizer 2ml

Eleaf iStick Pico Plus Mod: Eleaf IStick Pico Plus 75W Box Mod

Eleaf Melo 4S Tank: Eleaf Melo 4S Tank Atomizer 4ml

  • Locked
FastTech 9th Anniversary 15% off Site-Wide Coupon Sale-Ended

Hi Friends,

What an exceiting News! FastTech 9th Anniversary is coming! To celebrate the 9th anniversary of FastTech, we'll prepare a discount of 15% Site-wide and there are more surprises waiting for you! Are you ready?

----------------- Anniversary Site-Wide Coupon ----------------------

Offer: Site-wide 15% off
Valid Date: Jun 2, 2021 (UTC-6)
Coupon Code: FASTTECH2021

-----------------
FastTech 9th Anniversary Giveaway ----------------------

Offer: Mega Prize for 13 Winners
Valid Date: Jun 7, 2021 (UTC-6)
Purchase more than $40 to enter!


Click here to know more information of the anniversary promotion: FastTech 9th Anniversary 15% off Site-Wide

20210517-e0b230eab1a1447a8bf5d4fba8816a14.jpg


20210601-aeadbb62b2f549e1992b29df994be60c.jpg
  • Like
Reactions: pt91

  • Locked
In Stock! Geekvape Z Max Tank Atomizer 4ml

Geekvape Z Max Tank continues Z traditions, incorporating high-dynamic Top-to-side Airflow System with industry-leading Z-level leakproof design. Z Max Tank maintains 810 drip tip and 4ml bubble glass tube(2ml spare tube included) with top filling design. With the flavor turbo Geekvape M Series Coil, this Z engine can create massive clouds boundlessly, making cloud-chasing max and relax.



Features:
-Adjustable top airflow system, leakproof
-Top-to-bottom airflow
-Geekvape M series coils
-810 drip tip
...

Click here for more:

Geekvape Z Max Tank: Geekvape Z Max Tank Atomizer 4ml

  • Locked
New Arrival! FreeMax Onnix 20W Kit All Colors!

FreeMax Onnix 20W Kit is a compact pod system with 3-level adjustable power output and dual adjustable airflow system. The kit features 1100mAh internal battery for a whole-day vaping. Freemax Onnix 20W Pod Kit is charged with 1.5A Type-C fast charging port within 60 minutes. Button Activated and Draw Activated modes are both available for Onnix 20W kit. The pod has 3.5ml e-juice capacity with side refill design. Onnix 20W Kit comes with two OX series coils for both RDL & MTL vaping needs. OX Mesh Coil 0.5ohm is recommended with slider airflow control wide open to your preferences for Restricted-Direct-to-Lung (RDL), OX DVC Coil 1.0ohm is recommended with slider airflow control closed to your preferences for Mouth-To-Lung (MTL).


FreeMax-Onnix-Kit-15.jpg

FreeMax-Onnix-Kit-26.jpg


Features:
1. 20W compact pod system, 3-level adjustable power output
2. Dual adjustable airflow system for both MTL and RDL
3. 1100mAh internal battery, FM COILTECH4.0
4. Button Activated and Draw Activated modes
5. 3.5ml e-liquid capacity, refill at ease
6. 1.5A Type-C fast charging within 60 minutes
7. Compatible with OX Mesh 0.5ohm Coil/OX DVC 1.0ohm Coil
8. Simplistic modern style for maximum aesthetics and ergonomics design
...

Click here for more:

FreeMax Onnix Kit: FreeMax Onnix 20W Pod System Kit 1100mAh 3.5ml

  • Locked
Marvos T 80W VS Twister 80W VS Twister 30W

Freemax Marvos T 80W Pod Mod Kit consists of a Marvos DTL Pod and Marvos T Battery, which is inspired from Freemax's world-known Fireluke product line. Marvos T 80W is also a pen-style vape kit just like Freemax Twister 80W and Twister 30W Kit. The sub ohm tanks originally paired with Freemax Twister 80W and Twister 30W belong to fireluke series, so which one will you choose from these three vape starter kits?

Here are Freemax Vape Pen Kits:
Freemax Marvos T 80W Kit = Marvos DTL Pod + Marvos T Battery Mod
Freemax Twister 80W Kit = Fireluke 2 Tank + Twister 80W VW Mod
Freemax Twister 30W Kit = Fireluke 22 Tank + Twister 30W VW Mod

For more about Freemax vape kits, please click here>> Kits | Freemax - Taste the Clouds, Feel the Flavors!

36NDxpp.jpg
  • Like
Reactions: Javichu

  • Locked
[END] Card-style Pod -- Suorin Air Pro

185178665_895250594355593_8193903916243868570_n.jpg


Suorin Air Pro keeps the Suorin signature slimline look, the main body becomes smooth and rounded, while still housing an impressive 930mAh battery. It also comes with refillable pods that offer excellent vape experiences.

Easy to join in:
Describe suorin air pro in two words, and leave your comment.

Note:
* 2 winners will be announced on May, 24th
*Must be legal to vape



-------------------------------------------------------------

Thank you guys for joining Suorin giveaway! :toast:
Congrats to @alice-kanton and @rosesense
Please DM me with your shipping information within 48 hours.

  • Locked
New Arrival:Suorin Air Mod 40W Pod Kit 1500mAh

Today,I will introduce you the Suorin Air Mod 40W Pod Kit Uk.The Suorin Air Pod Mod Vape kit is built on a variety of improvements to the super popular Suorin Air design, while maintaining the classic card style design for which it is famous.Let's check it out.
suorin_air_mod_40w_pod_kit_colors.jpg

The Suorin Air is a thin card-style portable pod system kit uk best for vapers on the go. Constructed with recycled parts the Suorin Air Pod Mod ingeniously framed in solid Zinc Alloy on the one side, translucent and lightweight PCTG cover on the other side. The Suorin Air Pod Mod features an expanded 1500mAh built-in battery that can now fire all the way up to 40 watts.

The Suorin Air Pod Mod now features a new Z-Shape blowhole and upgraded atomization technology. The Suorin Air Pod Mod utilizes expanded 3ml capacity refillable empty pod cartridges that may be filled with your favorite e-Liquid including nicotine salt based e-Liquid flavors. The Suorin Pod Mod also features a 0.96-inch display to customize power and output modes. The Suorin Air Pod Mod may be charged using the bottom USB Type-C charging port for even faster charging compared to the original Suorin Air.

Please click UK Vape Shop Online, Best E-Cigs & E-Liquids Store to leran more details.

SPECIFICATION
Material:Zinc-Alloy+PCTG
Size:42.6mm x 14.1mm x 99.6mm
Battery:1500mAh
Output Power:5-40W
Charging:Type-C
Screen:0.96" TFT Screen
Capacity:3ml / 2ml(TPD/UK)
Filling: Side Filling
Resistance:0.6Ω/0.8Ω
Colors:Clear Silver, Clear Blue, Clear Green, Clear Red, Gunmetal, Black, Sunglow Red, Rainbow

Quick Link: Suorin Air Mod 40W Pod Kit 1500mAh

  • Locked
SXK ST Steam Tuners EDGE Clone RTA Rebuildable Tank Vape Atomizer 2ml 22mm

Welcome to the topic of New Product Introduction at 3fvape.com

Today I gonna introduce SXK ST Steam Tuners EDGE RTA Clone(Replica), the first SteamTuners rebuildable tank vape atomizer in 22mm diameter, compatible with 8 different air pins from 0.8mm ~ 3.0mm for MTL / DL vaping (Only 1.2mm and 3.0mm included).
SXK ST Steam Tuners EDGE Clone RTA Rebuildable Tank Atomizer holds 2.0ml capacity with top filling system in 22mm diameter. constructed from 316 stainless steel, SXK EDGE RTA Clone features simplest single coil build deck, easy for wicking and wiring.
SXK EDGE has a unique ULTEM Inner Sleeve that doubles as a heat reduction element and a wicking assist marker. SXK EDGE RTA Clone is compatible with 8 center airpins: 0.8mm / 1.0mm / 1.2mm / 1.5mm / 1.8mm / 2.0mm / 2.5mm / 3.0mm (Comes with 1.2mm and 3.0mm, others are not included).

510 threading connection
Single coil configuration
316 stainless steel construction, PC Tank
Peak Insulators
Compatible with 8 center airpins: 0.8mm / 1.0mm / 1.2mm / 1.5mm / 1.8mm / 2.0mm / 2.5mm / 3.0mm (Comes with 1.2mm and 3.0mm, others are not included), for MTL / DL
Diameter: 22mm
Capacity: 2.0ml
Filling method: Top filling system

More details about SXK ST Steam Tuners EDGE Clone RTA Rebuildable Tank Vape Atomizer, Please Check >> https://www.3fvape.com/49671-sxk-st-steam-tuners-edge-style-rta-rebuildable-tank-vape-atomizer.html

  • Locked
Auguse Era Pro RTA Rebuildable Tank Vape Atomizer 4.0ml 22mm


Today I gonna talk about Auguse Era Pro RTA, a 4.0ml single coil RTA in 22mm diameter by Auguse, featuring 4 different size air pin: 0.8mm / 1.0mm (Pre-installed) / 1.2mm / Blind.
Auguse Era Pro RTA Rebuildable Tank Atomizer holds 4.0ml capacity with top filling system in 22mm diameter. With bottom airflow and side airflow system and dual posts design, Auguse Era Pro RTA comes with 3pcs x 1.0mm airflow pin for the bottom airflow. In addition, Auguse Era Pro RTA adopts AFC ring with 7 level airflows: 1.6mm x 3.6mm, 1.8mm, 1.6mm, 1.4mm, 1.2mm, 1.0mm, 0.8mm, meeting your personal vaping demands. Auguse Era Pro RTA comes with 1 x 0.86ohm Coil, 1 x 0.68ohm Coil, a good vaping partner for most of your favorite mods with 510 threading connection.

510 threading connection
Single coil configuration
Dual posts design
Bottom airflow and side airflow system
4 customizable airflow sizes for the side airflow: 0.8mm, 1.0mm (pre-installed), 1.2mm, Blind
AFC ring with 7 level airflows: 1.6mm x 3.6mm, 1.8mm, 1.6mm, 1.4mm, 1.2mm, 1.0mm, 0.8mm
Size: 22mm x 64.5mm (with drip tip)
Capacity: 4.0ml
Filling method: Top filling system

More Details about Auguse Era Pro RTA Rebuildable Tank Vape Atomizer, Please Check >> https://www.3fvape.com/49669-auguse-era-pro-rta-rebuildable-tank-vape-atomizer.html

  • Locked
[ElegoMall Giveaway] OBS ENGINE 100W Box Kit - 2 Winners 5/24

Looking for some powerful box kit with better strong flavor and huge vapor? Here comes OBS ENGINE 100W kit to meet your vaping needs.

The Engine 100W is the first vaping device that can be replaceable battery sleeve, there are 6 different colors of battery sleeve for you to choose.

Powered by a single 18650/20700/21700 external battery to reach a maximum output of 100W. Featuring a 2A Type-C fast charging, which allows longer endurance as well as easier recharging.

OBS-ENGINE-100W-Box-Kit_01_2OsLG.jpeg


Learn More:
OBS ENGINE 100W

Want to get it now? Join us!

To enter:
1. What's your favorite vape device recentely?
2. Share your real thoughts or first impression of this NEW OBS Engine 100.
3. Tag your (3 or more) friends come to join too.

Notes:
1. You must over 21 years old.
2. 2 Lucky winners will be announced on 25th, May.
3. After receiving the prize, pls make the review on ECF. Thanks.
4. Number your entry, for instance: #Post 1

Please don’t hesitate to join us. Good luck! Looking forword to see our lucky winner. :)Stay tuned for ElgoMall for more latest vape kits and great deals.

  • Locked
Vape device number 21 not working.

One of you guys suggested the Voopoo drag x when I discussed my 20th vape device no longer charging through the USB mini. It was a Geekvape which they claim are indestructible. Of course they don't mention how the USB port is a cheap piece of garbage that will eventually fail even when treated delicately. I received the Voopoo drag x in the mail a couple days ago. I didn't realize it doesn't come with a battery so I picked up an IR18650-25R 20A 3.7V battery at a local vape shop. It was working beautifully for about a half hour and then it would just turn off. Even if I pushed the buttons or clicked five times, it wouldn't power up unless I took out the battery, put it back in and then clicked five times. Then I would get a few puffs and it would turn off again. Then today, I started receiving a message that said "atomizer short". I kept getting this message over and over even if I took out the coil and put it back in. Occasionally, it would start working again, but between the device powering off and the atomizer short problem, it's more or less unusable. It was only about $60 in total so no biggie. So now I'm shopping around for my 22nd vape device. Does anyone have any suggestions?

  • Locked
Vaporesso Luxe 2 - Trouble Connecting Parts

I can't screw this part in. It falls every time, I don't know if I am missing anything, maybe it's not even supposed to screw in. But still, everywhere I checked, it seems those parts are well connected where as in my case it drops off.

Attachments

  • WhatsApp Image 2021-05-17 at 21.12.30.jpeg
    WhatsApp Image 2021-05-17 at 21.12.30.jpeg
    88.2 KB · Views: 25

Filter