AFS Prime
- Thread starter harpo
- Start date
- th_trl_thread_readers 0
- Status
I use a Super T tip. There is no hole. I see a burn mark where the laser tried to make a hole but no hole.
I take a metal dental pick and make sure they are open. O also those super T tips were not really a good choice for my AFS use. They have too large of an opening and create a low juice flow problem. Not sure how to explain this but I have tried them and had to go back to the regular mouthpiece from a RN cart with the center part taken out. The smaller diameter hole in the end of the mouthpiece helps you get more juice into the atty.
I already did. Look guys the hole is not there. I can see the bottom one no problem but the top on only has a burn mark.
I just used it the way it was sent (atty was already in and facing what I assumed was downward). I'll have to check it when I take it apart to mark the hole permanently. Looking at it from the outside, it looks like the bottom cap (my bottom right now) is just a tiny bit thicker.
Debbie
Debbie concerning the line up:
If you have the AFS set up with the attie inside, unscrew it from the GG and then look at the bottom hole were it is located (the lasered hole is in line with this one), now just use a marker to put a dot on the AFS were the hole is. Don't make it permanent because if you are going to change atties, the hole might be on a different location when you screw it on the GG again.
Last edited:
We have heard that many times before. The hole is SOOOO small and hard to see without light shining directly though it.
Harpo,
I believe you when you say that there is no hole, if you have looked closely and it is not there. I can see the hole with my eyes and they are not perfect, it is very tiny but I can see it. On the new i atties, the whole is even smaller, but with no burning marks around it and I can see that one also. My advise: send them back to Rob!
I believe you when you say that there is no hole, if you have looked closely and it is not there. I can see the hole with my eyes and they are not perfect, it is very tiny but I can see it. On the new i atties, the whole is even smaller, but with no burning marks around it and I can see that one also. My advise: send them back to Rob!
here's a pic. Look at the the mark on the right it's just a burn mark, no indentation at all.
Attachments
Last edited:
Sorry but my eyes are not that good... hahah.... I have a little key chain light LED that will fit into the end of the atty. That is how I check them. I have seen them get a small particle in the hole from the cart also.
Yes Harpo, the picture is unclear. There is the burned mark, so a hole was made 4sure IMHO, but try it like Vapn said.
To all GG users:
I always try to make improvements, thats my job. If I stop this then we will not have always better products. I want to remind to all of you that I made a new AFS that is not complex at all, it doesnt leak, it has no learning curve, no laser holes and still automatic without having to push buttons to bring liquid inside atty. Also its more beautiful.
To all GG users:
I always try to make improvements, thats my job. If I stop this then we will not have always better products. I want to remind to all of you that I made a new AFS that is not complex at all, it doesnt leak, it has no learning curve, no laser holes and still automatic without having to push buttons to bring liquid inside atty. Also its more beautiful.
Yes Imeo that is great, but there are people out there who have the current AFS and the TW atties....we will help them as much as we can
Hole is there friend, try to open it by blowing air or suck it. Laser cant go wrong.
Yes Imeo that is great, but there are people out there who have the current AFS and the TW atties....we will help them as much as we can
Yes of course, thanks for the help and I am trying to do the same here. I just say what will come next so they have to know that they will not have any problem from now on.
I am trying to make better products. I try to satisfy the most dificult customers , so I try to make improvements
Small pieces of metal are inside the laser hole so it seems closed. It has to be opened by blowing or sucking air, thats all.
I poked a needle into the burn spot on my 4 extra attys, just in case. I couldn't get the needle in, barely if at all, and wondered if I needed smaller needles.
And then I used a large flashlight and locked myself in the bathroom (hubby thinks I'm crazy). I shined the light on the side of my 4 spare attys and saw a little itty, bitty speck of light shine thru, so they must be open.
I'll check the one in the AFS when I take it apart again.
Debbie
And then I used a large flashlight and locked myself in the bathroom (hubby thinks I'm crazy
). I shined the light on the side of my 4 spare attys and saw a little itty, bitty speck of light shine thru, so they must be open.I'll check the one in the AFS when I take it apart again.
Debbie
ok, let's get this solved:
Harpo: do you have a pin small enough to put through the hole and that it will come out in the other end?
Harpo: do you have a pin small enough to put through the hole and that it will come out in the other end?
I dont think that there is so small pin but we dont need it emonty. We need just a pin and the hole will open. I blow the atomizers in a blow machine so holes cant stay closed because air has big strength.
Harpo, if you find a blow machine in a gas station or in a store then blow the hole for 1-2 secs and you will see the hole immediately
- Status
