All new: The Precise Simplicity 14500 from Super-T Manufacturing Inc!

[andrebandre]

Is that a Micro B?

I have a Mini B due to arrive today. Looks great on Simplicity!

Yes.
As soon as pocket allows it, a Mini is also mandatory.

 

[andrebandre]

Yea just paste the link to your image into the body of your message here and put [img ] before the link and [/img ] after (without the extra spaces I put in there

If this trick works, i'll owe you my sanity.

 

[prof beard]

I'd like a pure wicked (not a Genny) dripping atomiser which is the same diameter as the Simplicity - preferably one without a side air hole. I'm using an eBaron Dripper Spiral at the moment which is perfect in all these requirements expect for being only 14mm diameter... Suggestions?

 

[Nach]

Cyclone maybe or its clone?

 

[Tanrichguy]

Cyclone is 14mm as well. The optional AFC for it adds a little bit. It's tough to find an atty that is the exact diameter of the simplicity. There is also the gap issue if it bothers you...

 

[Nach]

Not really tough... I'll post mine again!

Temon by MMVapors

 

[Tanrichguy]

Not really tough... I'll post mine again!

Temon by MMVapors

Ah yes. Forgot about the Temon. I'm good with performance over sleekness. (In no way suggesting the Temon is not a performer)

 

[Killjoy1]

Cyclone maybe or its clone?

But Cyclone has a side air hole. Perhaps the A7? I don't have one anymore to measure, but it took air in through the connector and I think it was somewhere in the 14-16mm width range (it just barely fit in the cup on a Reo Woodvil if that's any help)

 

[Nach]

How about a Reomizer? LOL

 

[villarino1k]

Is it possible to get the simplicity to a mirror finish without ruining the metal? Sorry for the dumb question

 

[txredxj]

I polished mine by hand. I only have 30 min in it but another hour should have it flawless. I used mag/aluminum wheel polish. It gets the uneven finish leveled out.

 

[vaptamist]

Please post pics when you're done

 

[txredxj]

It's really hard to pick up on camera how shiny it is due to the grooves. I have a 18650 on the way so I might be able to do a comparison between the two . Page 81 I have pics of how it is now and it looks like every other pic lol.

 

[skizif]

Any plans for an 18350 version???Sure would love one!!!

 

[vaptamist]

Grail 306 works and looks quite nicely.

 

[Jacoji]

I have a Diver Grail coming soon. Yay!

 

[txredxj]

comparison of polished 14500 and 18650

 

[Robinowitz]

I've been thinking about getting into rba's but wanted to practice on a cheap one first. Am expecting a Vulcnan Mini DID clone in the mail. I've done some research on them but wanted to get any feedback regarding using it with my Simplicity 13500. Any suggestions for number of wraps, etc. (I do have a Provari so that I can check ohms). Thank you!

 

[genghishahn]

I've been thinking about getting into RBA's but wanted to practice on a cheap one first. Am expecting a Vulcnan Mini DID clone in the mail. I've done some research on them but wanted to get any feedback regarding using it with my Simplicity 13500. Any suggestions for number of wraps, etc. (I do have a Provari so that I can check ohms). Thank you!

It's kinda going to depend on the size of your wick and wire when it comes to the number of wraps, but I aim for a 1.1 to 1.2 ohm coil. I find it to be a nice vape and it plays nice the amp limit on the AW IMR 14500s.

I don't have any experience with the DIDs, but a 3/4 wrap over a solid wick on my AGA using 30ga kanthal gets me 1.3 ohms.

Sent from my DROID RAZR using Tapatalk 4

 

[Robinowitz]

Thank you genghishahn! The DID clone comes with mesh. Curiously, does the AGA come in 16 mm diameter to fit the 13500. We are almost neighbors. I live in the Russian River Area!